EN 605 : 1992
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
PAINTS AND VARNISHES - STANDARD PANELS FOR TESTING
01-08-1997
12-01-2013
Cooperating organizations
National foreword
Foreword
Endorsement notice
Specification
0. Introduction
1. Scope and field of application
2. References
3. Steel panels
4. Tinplate panels
5. Aluminium panels
6. Glass panels
7. Asbestos-cement panels
8. Hardboard
9. Paper-faced plasterboard
Annexes
A. (informative) Mild steel for panels
B. (informative) General guidance on preparation of
steel panels by blast-cleaning
C. (normative) Determination of alkalinity of asbestos-
cement panels
Figure
Minimum value of Erichsen cup for cold-reduced mild steel
National annexes
NA (informative) Committees responsible
Specifies several types of standard panels and describes procedures for their preparation prior to painting. These standard panels are to be used in general methods of test for varnishes, paints and related products. Specifies the following types of standard panels: tinplate panels (prepared by abrasion and solvent cleaning); steel panels (prepared by solvent cleaning, abrasion, blast cleaning); glass panels (prepared by solvent and detergent cleaning); aluminium panels (prepared by solvent cleaning, acid chromating and abrasion); hardboard panels; asbestos cement panels; and paper faced plasterboard panels.
| Committee |
CEN/TC 139
|
| DevelopmentNote |
Replaces NFT 30-101, 30-102,30-103 and 30-104
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| NBN EN 605 : 1992 | Identical |
| NF EN 605 : 1992 | Identical |
| NEN EN 605 : 1993 | Identical |
| I.S. EN 605:1993 | Identical |
| UNI EN 605 : 1993 | Identical |
| UNE-EN 605:1994 | Identical |
| BS EN 605:1992 | Identical |
| DIN EN 605:1992-07 | Identical |
| DEFSTAN 80-158/1(1993) : INTERIM | PAINT, SYSTEM FOR AIRCRAFT - RAIN EROSION RESISTING POLYURETHANE - TWO-PACK - TYPES: HIGH GLOSS, SEMI MATT, MATT |
| I.S. EN ISO 1517:1995 | PAINTS AND VARNISHES - SURFACE-DRYING TEST - BALLOTINI METHOD |
| I.S. EN ISO 3678:1995 | PAINTS AND VARNISHES - PRINT-FREE TEST |
| 12/30254917 DC : DRAFT JAN 2012 | BS EN 877 - CAST IRON PIPES AND FITTINGS, THEIR JOINTS AND ACCESSORIES FOR THE EVACUATION OF WATER FROM BUILDINGS - REQUIREMENTS, TEST METHODS AND QUALITY ASSURANCE |
| DEFSTAN 80-176/1(1993) : INTERIM | VARNISH, COPAL, TYPE QX |
| DEFSTAN 80-171/1(1993) : INTERIM | INK, LIQUID, MARKING, QUICK DRYING |
| DEFSTAN 80-164/1(1993) : INTERIM | PAINT SYSTEM, FLUORESCENT - PAINT, FLUORESCENT, SINGLE-PACK - VARNISH, CLEAR, PROTECTIVE, TWO-PACK |
| BS EN 877 : 1999 | CAST IRON PIPES AND FITTINGS, THEIR JOINTS AND ACCESSORIES FOR THE EVACUATION OF WATER FROM BUILDINGS - REQUIREMENTS, TEST METHODS AND QUALITY ASSURANCE |
| I.S. EN 877:2000 | CAST IRON PIPES AND FITTINGS, THEIR JOINTS AND ACCESSORIES FOR THE EVACUATION OF WATER FROM BUILDINGS - REQUIREMENTS, TEST METHODS AND QUALITY ASSURANCE |
| UNI EN 877 : 2007 | CAST IRON PIPES AND FITTINGS, THEIR JOINTS AND ACCESSORIES FOR THE EVACUATION OF WATER FROM BUILDINGS - REQUIREMENTS, TEST METHODS AND QUALITY ASSURANCE |
| EN 61086-2:2004 | Coatings for loaded printed wire boards (conformal coatings) - Part 2: Methods of test |
| DIN EN 877:2010-01 | Cast iron pipes and fittings, their joints and accessories for the evacuation of water from buildings - Requirements, test methods and quality assurance (includes Amendment A1:2006 and Corrigendum AC:2008) |
| I.S. EN ISO 4623:1995 | PAINTS AND VARNISHES - FILIFORM CORROSION TEST ON STEEL |
| I.S. EN 61086-2:2004 | COATINGS FOR LOADED PRINTED WIRE BOARDS (CONFORMAL COATINGS) - PART 2: METHODS OF TEST |
| DEFSTAN 80-163/1(1993) : INTERIM | PAINT SYSTEM DEFENCE EQUIPMENT HEAVY DUTY (TWO PACK) - PAINT, PRIMING, DEFENCE EQUIPMENT HEAVY DUTY, EPOXIDE - PAINT UNDERCOAT, DEFENCE EQUIPMENT EPOXIDE PITCH - PAINT, FINISHING SPRAYING ELECTROSTATIC DIPPING |
| BS EN 61086-2:2004 | Coatings for loaded printed wire boards (conformal coatings) Methods of test |
| DEFSTAN 80-165/1(1993) : INTERIM | PAINT SYSTEM FOR SHIP'S WEATHERWORK, HIGH DURABILITY, LIGHT WEATHERWORK GREY - TYPE: BRUSHING |
| CEI EN 61086-2 : 2005 | COATINGS FOR LOADED PRINTED WIRE BOARDS (CONFORMAL COATINGS) - PART 2: METHODS OF TEST |
| ISO 1517:1973 | Paints and varnishes Surface-drying test Ballotini method |
| DEFSTAN 80-179/1(1993) : INTERIM | PAINT, EPOXY, SOLVENT FREE, TWO-PACK |
| DEFSTAN 80-178/1(1993) : INTERIM | PAINT, FINISHING MICACEOUS IRON OXIDE |
| ISO 3678:1976 | Paints and varnishes — Print-free test |
| ONORM EN 877 : 2008 | CAST IRON PIPES AND FITTINGS, THEIR JOINTS AND ACCESSORIES FOR THE EVACUATION OF WATER FROM BUILDINGS - REQUIREMENTS, TEST METHODS AND QUALITY ASSURANCE |
| EN ISO 4623 : 1995 | PAINTS AND VARNISHES - FILIFORM CORROSION TEST ON STEEL |
| EN ISO 3678:1995 | Paints and varnishes - Print-free test (ISO 3678:1976) |
| DEFSTAN 80-166/1(1993) : 1993 | PAINT SYSTEM DEFENCE EQUIPMENT - IRR MATT, (TWO-PACK) - PAINT, PRIMING, EPOXIDE, TYPE 1, FERROUS - PAINT; PRIMING, EPOXIDE, TYPE 2, NON-FERROUS - PAINT, UNDERCOAT, EPOXIDE - PAINT, FINISHING, IRR MATT, POLYURETHANE |
| DEFSTAN 80-174/1(1993) : INTERIM | PAINT SYSTEM, AMMUNITION, MATT, STOVING; PRIMING, AMMUNITION, EXTERIOR, STOVING; FINISHING, AMMUNITION, EXTERIOR MATT, STOVING, TYPE: SPRAYING |
| DEFSTAN 80-16/2(1993) : 1993 AMD 2 1995 | PAINT REMOVER, DICHLOROMETHANE, WATER RINSABLE, BRUSHING SPRAYING - TYPE 1 HIGH VISCOSITY (BRUSHING - TYPE 2 LOW VISCOSITY (SPRAYING) |
| DEFSTAN 80-175/1(1993) : INTERIM | VARNISH, AMMUNITION, STOVING, TYPE QX: CLASS A: EPOXY ESTER, CLASS B: SILICONE ALKYD, CLASS C: TUNG OIL PHENOLIC, TYPES: BRUSHING, SPRAYING AND DIPPING |
| ISO 1111-1:1983 | Single cold-reduced tinplate and single cold-reduced blackplate — Part 1: Electrolytic and hot-dipped tinplate sheet and blackplate sheet |
| ISO 2695:1976 | Fibre building boards Hard and medium boards for general purposes Quality specifications Appearance, shape and dimensional tolerances |
| ISO 3574:2012 | Cold-reduced carbon steel sheet of commercial and drawing qualities |
| ISO 6361-1:2011 | Wrought aluminium and aluminium alloys — Sheets, strips and plates — Part 1: Technical conditions for inspection and delivery |
| ISO 7337:1984 | Asbestos reinforced cement products — Guidelines for on-site work practices |
| ISO 396-2:1980 | Products in fibre reinforced cement Part 2: Silica-asbestos-cement flat sheets |
| ISO 6361-2:2014 | Wrought aluminium and aluminium alloys — Sheets, strips and plates — Part 2: Mechanical properties |
| ISO 468:1982 | Surface roughness — Parameters, their values and general rules for specifying requirements |
| ISO 396-1:1980 | Products in fibre reinforced cement Part 1: Asbestos-cement flat sheets |
| ISO 818:1975 | Fibre building boards — Definition — Classification |
| ISO 2696:1976 | Fibre building boards Hard and medium boards for general purposes Quality specifications Water absorption and swelling in thickness |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.