Skip to content
Please enter a keyword to search

  • EN 61347-2-10:2001/corrigendum:2010

    Current The latest, up-to-date edition.

    LAMP CONTROLGEAR - PART 2-10: PARTICULAR REQUIREMENTS FOR ELECTRONIC INVERTORS AND CONVERTORS FOR HIGH-FREQUENCY OPERATION OF COLD TUBULAR DISCHARGE LAMPS (NEON TUBES) (IEC 61347-2-10:2000/A1:2008)

    Available format(s): 

    Language(s): 

    Published date:  03-12-2010

    Publisher:  European Committee for Standards - Electrical

    Pure ENs are not available for sale, please purchase a suitable national adoption

    Sorry this product is not available in your region.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    FOREWORD
    INTRODUCTION
    1 Scope
    2 Normative references
    3 Definitions
    4 General requirements
    5 General notes on tests
    6 Classification
    7 Marking
    8 Terminals
    9 Provisions for earthing
    10 Protection against accidental contact with live parts
    11 Moisture resistance and insulation
    12 Electric strength
    13 Thermal endurance test for windings
    14 Normal conditions
    15 Abnormal conditions
    16 Fault conditions
    17 Construction
    18 Creepage distances and clearances
    19 Protective circuits
    20 Screws, current-carrying parts and connections
    21 Resistance to heat, fire and tracking
    22 Resistance to corrosion
    23 No-load rated output voltage and rated output current
    Annex A (normative) - Test to establish whether
            a conductive part is a live part which may cause
            an electric shock
    Annex B (normative) - Particular requirements for
            thermally protected lamp controlgear
    Annex C (normative) - Particular requirements for
            electronic lamp controlgear with means of protection
            against overheating
    Annex D (normative) - Requirements for carrying
            out the heating tests of thermally protected
            lamp controlgear
    Annex E (normative) - Use of constant S other than
            4500 in t[w] tests
    Annex F (normative) - Draught-proof enclosure
    Annex G (normative) - Explanation of the derivation
            of the values of pulse voltages
    Annex H (normative) - Tests
    Annex I (normative) - Measurement of currents and
            voltages in the output circuits of electronic invertors
            or convertors for neon tubes
    Annex ZA (normative) - Normative references to
             international publications with their corresponding
             European publications

    Abstract - (Show below) - (Hide below)

    This part of EN 61347 specifies general and safety requirements for lamp controlgear for use on d.c. supplies up to 250 V and/or a.c. supplies up to 1 000 V at 50 Hz or 60 Hz.

    General Product Information - (Show below) - (Hide below)

    Committee TC 34
    Development Note To be read in conjunction with EN 61347-1. (05/2010)
    Document Type Standard
    Publisher European Committee for Standards - Electrical
    Status Current

    Standards Referenced By This Book - (Show below) - (Hide below)

    I.S. EN 50107-1:2002:INC:AMD1:2004 SIGNS AND LUMINOUS-DISCHARGE-TUBE INSTALLATIONS OPERATING FROM A NO-LOAD RATED OUTPUT VOLTAGE EXCEEDING 1 KV BUT NOT EXCEEDING 10 KV - PART 1: GENERAL REQUIREMENTS
    BS EN 50107-1:2002 Signs and luminous-discharge-tube installations operating from a no-load rated output voltage exceeding 1 kV but not exceeding 10 kV General requirements
    16/30342256 DC : 0 BS EN 50107-3 - PRODUCT STANDARD COVERING LUMINOUS SIGNS WITH DISCHARGE LAMPS AND/OR LED (LIGHT EMITTING DIODES) AND/OR EL (ELECTROLUMINESCENT) LIGHTSOURCES WITH A NOMINAL VOLTAGE NOT EXCEEDING 1000 V, WITH THE EXCLUSION OF GENERAL LIGHTING, TRAFFIC- OR EMERGENCY RELATED PURPOSE
    PREN 50107-3 : DRAFT 2016 PRODUCT STANDARD COVERING LUMINOUS SIGNS WITH DISCHARGE LAMPS AND/OR LED (LIGHT EMITTING DIODES) AND/OR EL (ELECTROLUMINESCENT) LIGHTSOURCES WITH A NOMINAL VOLTAGE NOT EXCEEDING 1000 V, WITH THE EXCLUSION OF GENERAL LIGHTING, TRAFFIC- OR EMERGENCY RELATED PURPOSE
    CEI EN 60598-2-14 : 2010 LUMINAIRES - PART 2-14: PARTICULAR REQUIREMENTS - LUMINAIRES FOR COLD CATHODE TUBULAR - DISCHARGE LAMPS (NEON TUBES) AND SIMILAR EQUIPMENT
    01/206090 DC : DRAFT OCT 2001 EN 50107-2 - SIGNS AND LUMINOUS-DISCHARGE-TUBE INSTALLATIONS OPERATING FROM A NO-LOAD RATED OUTPUT VOLTAGE EXCEEDING 1 KV BUT NOT EXCEEDING 10 KV - PART 2: REQUIREMENTS FOR EARTH-LEAKAGE AND OPEN-CIRCUIT PROTECTIVE DEVICES
    BS EN 60598-2-14:2009 Luminaires Particular requirements. Luminaires for cold cathode tubular discharge lamps (neon tubes) and similar equipment
    I.S. EN 50107-1:2002 SIGNS AND LUMINOUS-DISCHARGE-TUBE INSTALLATIONS OPERATING FROM A NO-LOAD RATED OUTPUT VOLTAGE EXCEEDING 1 KV BUT NOT EXCEEDING 10 KV - PART 1: GENERAL REQUIREMENTS
    EN 60598-2-14:2009 Luminaires - Part 2-14: Particular requirements - Luminaires for cold cathode tubular discharge lamps (neon tubes) and similar equipment
    EN 50107-1 : 2002 AMD 1 2004 SIGNS AND LUMINOUS-DISCHARGE-TUBE INSTALLATIONS OPERATING FROM A NO-LOAD RATED OUTPUT VOLTAGE EXCEEDING 1 KV BUT NOT EXCEEDING 10 KV - PART 1: GENERAL REQUIREMENTS

    Standards Referencing This Book - (Show below) - (Hide below)

    IEC 61347-1:2015 RLV Lamp controlgear - Part 1: General and safety requirements
    EN 61347-1:2015 Lamp controlgear - Part 1: General and safety requirements
    ISO 3864:1984 Safety colours and safety signs
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective