• EN 61347-2-4:2001/corrigendum:2010

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

    LAMP CONTROLGEAR - PART 2-4: PARTICULAR REQUIREMENTS FOR D.C. SUPPLIED ELECTRONIC BALLASTS FOR GENERAL LIGHTING

    Available format(s): 

    Superseded date:  01-07-2011

    Language(s): 

    Published date:  12-01-2013

    Publisher:  European Committee for Standards - Electrical

    Pure ENs are not available for sale, please purchase a suitable national adoption

    Sorry this product is not available in your region.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    FOREWORD
    INTRODUCTION
    1 Scope
    2 Normative references
    3 Definitions
    4 General requirements
    5 General notes on tests
    6 Classification
    7 Marking
       7.1 Mandatory markings
       7.2 Information to be provided, if applicable
    8 Protection against accidental contact with live
       parts
    9 Terminals
    10 Provisions for earthing
    11 Moisture resistance and insulation
    12 Electric strength
    13 Thermal endurance test for windings
    14 Pulse voltages
    15 Abnormal conditions
       15.1 Removal of lamp(s)
       15.2 Lamp fails to start (cathodes intact
            electrically)
       15.3 Polarity reversal
    16 Fault conditions
    17 Construction
    18 Creepage distances and clearances
    19 Screws, current-carrying parts and connections
    20 Resistance to heat, fire and tracking
    21 Resistance to corrosion
    Annex A (normative) Test to establish whether a
             conductive part is a live part, which may
             cause an electric shock
    Annex B (normative) Particular requirements for
             thermally protected lamp controlgear
    Annex C (normative) Particular requirements for
             electronic lamp controlgear with means of
             protection against overheating
    Annex D (normative) Requirements for carrying out the
             heating tests of thermally protected lamp
             controlgear
    Annex E (normative) Use of constant S other than 4500
             in t[w] tests
    Annex F (normative) Draught-proof enclosure
    Annex G (normative) Explanation of the derivation of
             the values of pulse voltages
    Annex H (normative) Tests
    Annex ZA (normative) Normative references to
             international publications with their
             corresponding European publications
    Table 1 - Pulse voltages

    Abstract - (Show below) - (Hide below)

    Specifies particular safety requirements for d.c. supplied electronic ballasts intended for operation from transient and surge-free power sources, operated directly from batteries without charging equipment as used in leisure equipment.

    General Product Information - (Show below) - (Hide below)

    Committee TC 34
    Development Note To be used in conjunction with EN 61347-1 (10/2003) Together with EN 61347-1 and parts 2-1, 2-2, 2-3, 2-5, 2-6, 2-7, 2-8 and 2-9 of EN 61347 supersedes EN 60920, EN 60922, EN 60924, EN 60926, EN 60928 and EN 61046. (07/2005)
    Document Type Standard
    Publisher European Committee for Standards - Electrical
    Status Superseded
    Superseded By
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    I.S. EN 60079-15:2010 EXPLOSIVE ATMOSPHERES - PART 15: EQUIPMENT PROTECTION BY TYPE OF PROTECTION 'N'
    CEI EN 60079-15 : 2012 EXPLOSIVE ATMOSPHERES - PART 15: EQUIPMENT PROTECTION BY TYPE OF PROTECTION 'N'
    EN 60079-15:2010 EXPLOSIVE ATMOSPHERES - PART 15: EQUIPMENT PROTECTION BY TYPE OF PROTECTION "N"
    BS EN 60079-15:2010 EXPLOSIVE ATMOSPHERES - PART 15: EQUIPMENT PROTECTION BY TYPE OF PROTECTION 'N'
    UNE-EN 60079-15:2013 Explosive atmospheres - Part 15: Equipment protection by type of protection "n"

    Standards Referencing This Book - (Show below) - (Hide below)

    IEC 60112:2003+AMD1:2009 CSV Method for the determination of the proof and the comparative tracking indices of solid insulating materials
    IEC 61347-1:2015 RLV Lamp controlgear - Part 1: General and safety requirements
    IEC 60925:1989+AMD1:1996+AMD2:2001 CSV DC supplied electronic ballasts for tubular fluorescent lamps - Performance requirements
    IEC 60317-0-1:2013 Specifications for particular types of winding wires - Part 0-1: General requirements - Enamelled round copper wire
    EN 61347-1:2015 LAMP CONTROLGEAR - PART 1: GENERAL AND SAFETY REQUIREMENTS (IEC 61347-1:2015)
    IEC 60529:1989+AMD1:1999+AMD2:2013 CSV Degrees of protection provided by enclosures (IP Code)
    IEC 60691:2015 Thermal-links - Requirements and application guide
    IEC 60598-1:2014+AMD1:2017 CSV Luminaires - Part 1: General requirements and tests
    EN 60925:1991/A2:2001 SPECIFICATION FOR PERFORMANCE REQUIREMENTS FOR D.C. SUPPLIED ELECTRONIC BALLASTS FOR TUBULAR FLUORESCENT LAMPS
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective