• I.S. EN 61347-2-4:2001

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

    LAMP CONTROLGEAR - PART 2-4: PARTICULAR REQUIREMENTS FOR D.C. SUPPLIED ELECTRONIC BALLASTS FOR GENERAL LIGHTING (IEC 61347-2-4:2000 (EQV))

    Available format(s):  Hardcopy, PDF

    Superseded date:  15-11-2011

    Language(s):  English

    Published date:  01-01-2001

    Publisher:  National Standards Authority of Ireland

    For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
    Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

    Dates of withdrawal of national standards are available from NSAI.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    FOREWORD
    INTRODUCTION
    1 Scope
    2 Normative references
    3 Definitions
    4 General requirements
    5 General notes on tests
    6 Classification
    7 Marking
    8 Protection against accidental contact with live
       parts
    9 Terminals
    10 Provisions for earthing
    11 Moisture resistance and insulation
    12 Electric strength
    13 Thermal endurance test for windings
    14 Pulse voltages
    15 Abnormal conditions
    16 Fault conditions
    17 Construction
    18 Creepage distances and clearances
    19 Screws, current-carrying parts and connections
    20 Resistance to heat, fire and tracking
    21 Resistance to corrosion
    Annex A (normative) - Test to establish whether a
            conductive part is a live part, which may
            cause an electric shock
    Annex B (normative) - Particular requirements for
            thermally protected lamp controlgear
    Annex C (normative) - Particular requirements for
            electronic lamp controlgear with means of
            protection against overheating
    Annex D (normative) - Requirements for carrying out the
            heating tests of thermally protected lamp
            controlgear
    Annex E (normative) - Use of constant S other than 4500
            in t[w] tests
    Annex F (normative) - Draught-proof enclosure
    Annex G (normative) - Explanation of the derivation of
            the values of pulse voltages
    Annex H (normative) - Tests
    Annex ZA (normative) - Normative references to
             international publications with their
             corresponding European publications
    Table 1 - Pulse voltages

    Abstract - (Show below) - (Hide below)

    Gives particular safety requirements for d.c supplied electronic ballasts intended for operation from transient and surge-free power sources, operated directly from batteries without charging equipment as used in leisure equipment, for example, caravans, etc.

    General Product Information - (Show below) - (Hide below)

    Development Note Together with I.S. EN 61347-1 and parts 2-1, 2-2, 2-3, 2-5, 2-6, 2-7, 2-8 and 2-9 of I.S. EN 61347 supersedes I.S. EN 60920, I.S. EN 60922, I.S. EN 60924, I.S. EN 60926, I.S. EN 60928 and I.S. EN 61046. (07/2005)
    Document Type Standard
    Publisher National Standards Authority of Ireland
    Status Superseded
    Superseded By
    Supersedes

    Standards Referencing This Book - (Show below) - (Hide below)

    IEC 61347-1:2015 RLV Lamp controlgear - Part 1: General and safety requirements
    IEC 60925:1989+AMD1:1996+AMD2:2001 CSV DC supplied electronic ballasts for tubular fluorescent lamps - Performance requirements
    EN 61347-1:2015 Lamp controlgear - Part 1: General and safety requirements
    EN 60925:1991/A2:2001 SPECIFICATION FOR PERFORMANCE REQUIREMENTS FOR D.C. SUPPLIED ELECTRONIC BALLASTS FOR TUBULAR FLUORESCENT LAMPS
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective