![header thumbnail](/images/img-default-logo.png)
EN 792-13:2000+A1:2008
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
![header thumbnail](/images/img-default-logo.png)
Hand-held non-electric power tools - Safety requirements - Part 13: Fastener driving tools
24-03-2022
24-09-2008
Foreword
Introduction
1 Scope
2 Normative references
3 Definitions
4 List of hazards
5 Safety requirements and/or measures
6 Verification
7 User Information, operating instructions
Annex A (normative) - Assessment procedure to prove the
necessity of a safe yoke
Annex AA (informative) - Computational Examples for
Determination of Safety Yoke Conditions
Annex B (informative) - Noise reduction
Annex C (informative) - Information on ergonomic design of
the handle
Annex D (informative) - Sample operating instructions for
fastener driving tools operated by compressed air
Annex ZA (informative) - Relationship between this European
Standard and the Essential Requirements of EU
Directive 98/37/EC
Annex ZB (informative) - Relationship between this European
Standard and the Essential Requirements of EU Directive
2006/42/EC
Bibliography
This standard is applicable to fastener driving tools which are handled by one person and in which energy in a linear movement is applied to a loaded fastener for the purpose of driving this into a workpiece of a determined material. During the driving operation, the fastener leaves the tool partially or entirely, with sufficient velocity to overcome the resistance of penetration, and forms a mechanical connection or attachment of different workpieces. The energy required for driving a fastener is provided by compressed air or combustible gases.NOTE 1Fastener driving tools are also referred to for example as Nailers, Staplers, Tackers, Pinners.NOTE 2The workpiece material can, for example, consist of wood, wooden materials, plastic material, fibre materials - loose or condensed, cement- and lime materials, metal.This standard contains requirements for the design, marking and information for use of fastener driving tools, corresponding to the specific hazards listed in clause 4. The standard sets out the means of verification for these requirements. Where, for clarity, an example of a safety measure is given in the text, this shall not be considered as the only possible solution. Any other solution leading to the same risk reduction is permissible if an equivalent level of safety is achieved.This standard is applicable to fastener driving tools which have been produced after the date of publication of the standard.This standard is not applicable to stapling pliers and vibration hammers.NOTE 3"Stapling pliers" are handheld power operated tools equipped with a fixed or moving anvil bar in front of the muzzle, which are used predominantly for joining paper, leather, textiles and similar materials.This standard is not applicable to fastener driving tools in which the energy for driving fasteners is drawn from cartridges or from any type of electric supply.
Committee |
CEN/TC 255
|
DevelopmentNote |
2000 Edition Re-Issued in September 2008 & incorporates AMD 1 2008. (10/2008)
|
DocumentType |
Standard
|
PublisherName |
Comite Europeen de Normalisation
|
Status |
Superseded
|
SupersededBy |
Standards | Relationship |
SN EN 792-13 : 2000 + A1 2008 | Identical |
NEN EN 792-13 : 2000 + A1 2008 | Identical |
DIN EN 792-13:2009-01 | Identical |
I.S. EN 792-13:2000 | Identical |
NF EN 792-13 : 2000 + A1 2008 | Identical |
BS EN 792-13 : 2000 | Identical |
NS EN 792-13 : 2000 + A1 2008 | Identical |
PN EN 792-13 : 2004 + A1 2008 | Identical |
NBN EN 792-13 : 2000 + A1 2009 | Identical |
UNI EN 792-13 : 2009 | Identical |
UNE-EN 792-13:2001 | Identical |
I.S. EN 792-13:2000+A1:2008 | Identical |
UNE-EN 792-13:2001+A1:2008 | Identical |
BS EN 15895 : 2011 | CARTRIDGE OPERATED HAND-HELD TOOLS - SAFETY REQUIREMENTS - FIXING AND HARD MARKING TOOLS |
BS EN 12549 : 1999 | ACOUSTICS - NOISE TEST CODE FOR FASTENER DRIVING TOOLS - ENGINEERING METHOD |
EN 12549:1999+A1:2008 | Acoustics - Noise test code for fastener driving tools - Engineering method |
I.S. TS 8662-11:2004 | HAND-HELD PORTABLE POWER TOOLS - MEASUREMENT OF VIBRATIONS AT THE HANDLE - PART 11: FASTENER DRIVING TOOLS |
I.S. EN 12549:1999 | ACOUSTICS - NOISE TEST CODE FOR FASTENER DRIVING TOOLS - ENGINEERING METHOD |
UNI EN 15895 : 2011 | CARTRIDGE OPERATED HAND-HELD TOOLS - SAFETY REQUIREMENTS - FIXING AND HARD MARKING TOOLS |
EN 15895:2011+A1:2018 | Cartridge operated hand-held tools - Safety requirements - Fixing and hard marking tools |
DIN EN 12549:2008-12 | ACOUSTICS - NOISE TEST CODE FOR FASTENER DRIVING TOOLS - ENGINEERING METHOD |
UNI EN 12549 : 2009 | ACOUSTICS - NOISE TEST CODE FOR FASTENER DRIVING TOOLS - ENGINEERING METHOD |
ISO 8662-11:1999 | Hand-held portable power tools Measurement of vibrations at the handle Part 11: Fastener driving tools |
CEN ISO/TS 8662-11:2004/AC:2004 | HAND-HELD PORTABLE POWER TOOLS - MEASUREMENT OF VIBRATIONS AT THE HANDLE - PART 11: FASTENER DRIVING TOOLS |
I.S. EN 15895:2011 | CARTRIDGE OPERATED HAND-HELD TOOLS - SAFETY REQUIREMENTS - FIXING AND HARD MARKING TOOLS |
DIN EN 15895:2011-08 | CARTRIDGE OPERATED HAND-HELD TOOLS - SAFETY REQUIREMENTS - FIXING AND HARD MARKING TOOLS |
EN 12096:1997 | Mechanical vibration - Declaration and verification of vibration emission values |
ISO 4871:1996 | Acoustics — Declaration and verification of noise emission values of machinery and equipment |
ISO/TR 11688-1:1995 | Acoustics Recommended practice for the design of low-noise machinery and equipment Part 1: Planning |
EN 349:1993+A1:2008 | Safety of machinery - Minimum gaps to avoid crushing of parts of the human body |
EN 50144-1 : 98 COR 2005 | SAFETY OF HAND-HELD ELECTRIC MOTOR OPERATED TOOLS - PART 1: GENERAL REQUIREMENTS |
EN 614-1:2006+A1:2009 | Safety of machinery - Ergonomic design principles - Part 1: Terminology and general principles |
EN 292-1 : 1991 | SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - BASIC TERMINOLOGY, METHODOLOGY |
EN 563:1994/A1:1999/AC:2000 | SAFETY OF MACHINERY - TEMPERATURES OF TOUCHABLE SURFACES - ERGONOMICS DATA TO ESTABLISH TEMPERATURE LIMIT VALUES FOR HOT SURFACES |
EN 12549:1999+A1:2008 | Acoustics - Noise test code for fastener driving tools - Engineering method |
VBG 44 : 1997 | PORTABLE DRIVE-IN DEVICES |
ISO 8662-11:1999 | Hand-held portable power tools Measurement of vibrations at the handle Part 11: Fastener driving tools |
ISO 11690-1:1996 | Acoustics Recommended practice for the design of low-noise workplaces containing machinery Part 1: Noise control strategies |
EN 547-3:1996+A1:2008 | Safety of machinery - Human body measurements - Part 3: Anthropometric data |
EN 292-2 : 91 AMD 1 95 | SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - TECHNICAL PRINCIPLES AND SPECIFICATION |
EN ISO 4871:2009 | Acoustics - Declaration and verification of noise emission values of machinery and equipment (ISO 4871:1996) |
1998/37/EC : 1998 | DIRECTIVE 98/37/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 22 JUNE 1998 ON THE APPROXIMATION OF THE LAWS OF THE MEMBER STATES RELATING TO MACHINERY |
EN ISO 11688-1:2009 | Acoustics - Recommended practice for the design of low-noise machinery and equipment - Part 1: Planning (ISO/TR 11688-1:1995) |
EN ISO 11690-1 : 1996 | ACOUSTICS - RECOMMENDED PRACTICE FOR THE DESIGN OF LOW-NOISE WORKPLACES CONTAINING MACHINERY - NOISE CONTROL STRATEGIES |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.