• Shopping Cart
    There are no items in your cart

EN ISO 10360-5:2010

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by

Geometrical product specifications (GPS) - Acceptance and reverification tests for coordinate measuring machines (CMM) - Part 5: CMMs using single and multiple stylus contacting probing systems (ISO 10360-5:2010)

Superseded date

23-04-2020

Superseded by

EN ISO 10360-5:2020

Published date

15-09-2010

Sorry this product is not available in your region.

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols
5 Requirements for metrological characteristics
6 Acceptance tests and reverification tests
7 Compliance with specification
8 Applications
9 Indication in product documentation and data sheets
Annex A (informative) Symbols and subscripts
Annex B (informative) Checking the probing system prior
        to the ISO 10360-2 test
Annex C (informative) Interpretation of multi-stylus
        test results
Annex D (normative) Maximum permissible error/limit
        figures
Annex E (informative) Relation to the GPS matrix model
Bibliography

ISO 10360-5:2010 specifies acceptance and periodic reverification tests of CMM performance with contacting probing systems and is only applicable to CMMs using any type of contacting probing system, a discrete point probing mode, and spherical or hemispherical stylus tip(s).It complements ISO 10360-7, which is the module for CMMs with video probing systems, and ISO 10360-2, which is universal, i.e. not probe-type specific.ISO 10360-5:2010 applies to CMMs supplied with any of the following: single-stylus probing system; multi-stylus probing systems with fixed multiple styli attached to a single probe (e.g. “star” stylus); multiple probing systems such as those with a stylus for each of their probes; systems with articulating probing; stylus and probe changing systems; manual (non-driven) CMMs.ISO 10360-5:2010 is not applicable to non-contacting probing systems, which require different testing procedures.

Committee
CEN/TC 290
DocumentType
Standard
PublisherName
Comite Europeen de Normalisation
Status
Superseded
SupersededBy

VDI/VDE 2617 Blatt 10:2011-01 Accuracy of coordinate measuring machines - Characteristics and their checking - Acceptance and reverification tests of lasertrackers
VDI/VDE 2617 Blatt 2.1:2014-03 Accuracy of coordinate measuring machines - Parameters and their reverification - Code of practice for the application of DIN EN ISO 10360-2 for length measurement
VDI/VDE 2617 Blatt 13; VDI/VDE 2630 Blatt 1.3:2011-12 VDI/VDE 2617 Blatt 13: Accuracy of coordinate measuring machines - Characteristics and their testing - Guideline for the application of DIN EN ISO 10360 for coordinate measuring machines with CT-sensors - VDI/VDE 2630 Blatt 1.3: Computed tomography in dimensional measurement - Guideline for the application of DIN EN ISO 10360 for coordinate measuring machines with CT-sensors
VDI/VDE 2617 Blatt 11:2011-03 Accuracy of coordinate measuring machines - Characteristics and their checking - Determination of the uncertainty of measurement for coordinate measuring machines using uncertainty budgets

ISO 10360-4:2000 Geometrical Product Specifications (GPS) Acceptance and reverification tests for coordinate measuring machines (CMM) Part 4: CMMs used in scanning measuring mode
ISO/TR 14638:1995 Geometrical product specification (GPS) Masterplan
ISO 10360-1:2000 Geometrical Product Specifications (GPS) — Acceptance and reverification tests for coordinate measuring machines (CMM) — Part 1: Vocabulary
ISO 14253-1:2017 Geometrical product specifications (GPS) — Inspection by measurement of workpieces and measuring equipment — Part 1: Decision rules for verifying conformity or nonconformity with specifications
ISO/IEC Guide 99:2007 International vocabulary of metrology Basic and general concepts and associated terms (VIM)
ISO 10360-3:2000 Geometrical Product Specifications (GPS) Acceptance and reverification tests for coordinate measuring machines (CMM) Part 3: CMMs with the axis of a rotary table as the fourth axis
ISO 10360-2:2009 Geometrical product specifications (GPS) Acceptance and reverification tests for coordinate measuring machines (CMM) Part 2: CMMs used for measuring linear dimensions
ISO/TS 23165:2006 Geometrical product specifications (GPS) — Guidelines for the evaluation of coordinate measuring machine (CMM) test uncertainty

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.