EN ISO 11296-3:2011
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 3: Lining with close-fit pipes (ISO 11296-3:2009+Cor 1:2011)
11-05-2011
21-03-2019
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviated terms
5 Pipes at the "M" stage
6 Fittings
7 Ancillary components
8 Fitness for purpose of the installed lining system at
the "I" stage
9 Installation practice
Annex A (normative) - Factory folded heat reverted
polyethylene (PE) pipe - Determination of
memory ability
Annex B (normative) - Folded polyethylene (PE) pipe -
Determination of resistance to circumferential
tensile stress at constant temperature
Bibliography
ISO 11296-3:2009, in conjunction with ISO 11296-1, specifies requirements and test methods for close-fit lining systems intended to be used for the renovation of non-pressure drainage and sewerage networks.It applies to pipes and fittings made of polyethylene (PE) or unplasticized poly(vinyl chloride) (PVC‑U). It is applicable to the plastic lining system only.
| Committee |
CEN/TC 155
|
| DevelopmentNote |
Supersedes EN 13566-3. (05/2011)
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| NEN EN ISO 11296-3 : 2011 | Identical |
| PN EN ISO 11296-3 : 2013 | Identical |
| ÖNORM EN ISO 11296-3: 2019-3 | Identical |
| DIN EN ISO 11296-3:2011-07 | Identical |
| BS EN ISO 11296-3:2011 | Identical |
| DIN EN ISO 11296-3:2019-05 | Identical |
| BS EN ISO 11296-3:2018 | Identical |
| ISO 11296-3:2009 | Identical |
| NS EN ISO 11296-3 : 2011 | Identical |
| ONORM EN ISO 11296-3 : 2011 | Identical |
| I.S. EN ISO 11296-3:2011 | Identical |
| I.S. EN ISO 11296-3:2018 | Identical |
| NF EN ISO 11296-3 : 2011 | Identical |
| NBN EN ISO 11296-3 : 2011 | Identical |
| NEN-EN-ISO 11296-3:2018 en | Identical |
| ISO 11296-3:2018 | Identical |
| UNE-EN ISO 11296-3:2011 | Identical |
| PREN 15885 : DRAFT 2015 | CLASSIFICATION AND CHARACTERISTICS OF TECHNIQUES FOR RENOVATION, REPAIR AND REPLACEMENT OF DRAINS AND SEWERS |
| 16/30332542 DC : 0 | BS EN 15885 - CLASSIFICATION AND CHARACTERISTICS OF TECHNIQUES FOR RENOVATION, REPAIR AND REPLACEMENT OF DRAINS AND SEWERS |
| ISO 13953:2001 | Polyethylene (PE) pipes and fittings — Determination of the tensile strength and failure mode of test pieces from a butt-fused joint |
| ISO 8772:2006 | Plastics piping systems for non-pressure underground drainage and sewerage — Polyethylene (PE) |
| ISO 2507-1:1995 | Thermoplastics pipes and fittings — Vicat softening temperature — Part 1: General test method |
| ISO 11295:2017 | Classification and information on design and applications of plastics piping systems used for renovation and replacement |
| ISO 12176-1:2017 | Plastics pipes and fittings — Equipment for fusion jointing polyethylene systems — Part 1: Butt fusion |
| ISO 527-2:2012 | Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics |
| ISO 11296-1:2009 | Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks — Part 1: General |
| ISO 6259-1:2015 | Thermoplastics pipes — Determination of tensile properties — Part 1: General test method |
| ISO 3126:2005 | Plastics piping systems — Plastics components — Determination of dimensions |
| ISO 18373-1:2007 | Rigid PVC pipes — Differential scanning calorimetry (DSC) method — Part 1: Measurement of the processing temperature |
| ISO 4435:2003 | Plastics piping systems for non-pressure underground drainage and sewerage — Unplasticized poly(vinyl chloride) (PVC-U) |
| ISO 9967:2016 | Thermoplastics pipes — Determination of creep ratio |
| ISO 899-1:2017 | Plastics — Determination of creep behaviour — Part 1: Tensile creep |
| ISO 21138-1:2007 | Plastics piping systems for non-pressure underground drainage and sewerage — Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) — Part 1: Material specifications and performance criteria for pipes, fittings and system |
| ISO 9969:2016 | Thermoplastics pipes — Determination of ring stiffness |
| ISO 9852:2007 | Unplasticized poly(vinyl chloride) (PVC-U) pipes — Dichloromethane resistance at specified temperature (DCMT) — Test method |
Access your standards online with a subscription
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.