• There are no items in your cart

EN ISO 15138:2007

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by

Petroleum and natural gas industries - Offshore production installations - Heating, ventilation and air-conditioning (ISO 15138:2007)

Superseded date

09-07-2019

Published date

15-12-2007

Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Abbreviated terms
5 Design
  5.1 Introduction
  5.2 Development of design basis
  5.3 System design - General
  5.4 Area-specific system design
  5.5 Equipment and bulk selection
  5.6 Installation and commissioning
Annex A (normative) - Equipment and bulk selection
Annex B (normative) - Installation and commissioning
Annex C (informative) - Operation and maintenance
Annex D (informative) - Datasheets
Annex E (normative) - Standard data for flanges
Bibliography

ISO 15138:2007 specifies requirements and provides guidance for design, testing, installation and commissioning of heating, ventilation, air-conditioning and pressurization systems and equipment on all offshore production installations for the petroleum and natural gas industries that are new or existing, normally occupied by personnel, or not normally occupied by personnel; or fixed or floating but registered as an offshore production installation.

For installations that can be subject to "Class" or "IMO/MODU Codes & Resolutions", the user is referred to HVAC requirements under these rules and resolutions. When these requirements are less stringent than those being considered for a fixed installation, then it is necessary that ISO 15138:2007, i.e. requirements for fixed installations, be utilized.

Committee
CEN/TC 12
DocumentType
Standard
PublisherName
Comite Europeen de Normalisation
Status
Superseded
SupersededBy

ISO 12499:1999 Industrial fans Mechanical safety of fans Guarding
IEC 60079-10:2002 Electrical apparatus for explosive gas atmospheres - Part 10: Classification of hazardous areas
EN 1886:2007 Ventilation for buildings - Air handling units - Mechanical performance
EN 1507:2006 Ventilation for buildings - Sheet metal air ducts with rectangular section - Requirements for strength and leakage
EN 13053:2006+A1:2011 Ventilation for buildings - Air handling units - Rating and performance for units, components and sections
ISO 3744:2010 Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Engineering methods for an essentially free field over a reflecting plane
EN 1505:1997 Ventilation for buildings - Sheet metal air ducts and fittings with rectangular cross section - Dimensions
NS 5575 : 1ED 1987 VENTILATION DUCTS - IDENTIFICATION COLOURS
NFPA 96 : 2017 VENTILATION CONTROL AND FIRE PROTECTION OF COMMERCIAL COOKING OPERATIONS
EN 378-4:2016 Refrigerating systems and heat pumps - Safety and environmental requirements - Part 4: Operation, maintenance, repair and recovery
ISO 14694:2003 Industrial fans — Specifications for balance quality and vibration levels
EN 378-1:2016 Refrigerating systems and heat pumps - Safety and environmental requirements - Part 1: Basic requirements, definitions, classification and selection criteria
EN 378-3:2016 Refrigerating systems and heat pumps - Safety and environmental requirements - Part 3: Installation site and personal protection
ISO 7547:2002 Ships and marine technology Air-conditioning and ventilation of accommodation spaces Design conditions and basis of calculations
ISO 16812:2007 Petroleum, petrochemical and natural gas industries Shell-and-tube heat exchangers
ISO 5149:1993 Mechanical refrigerating systems used for cooling and heating Safety requirements
ISO 9309:1989 Refrigerant compressors Presentation of performance data
ISO 8861:1998 Shipbuilding — Engine-room ventilation in diesel-engined ships — Design requirements and basis of calculations
ISO 1940-1:2003 Mechanical vibration Balance quality requirements for rotors in a constant (rigid) state Part 1: Specification and verification of balance tolerances
ISO 917:1989 Testing of refrigerant compressors
AMCA 500 : 1994 TEST METHODS FOR LOUVERS, DAMPERS AND SHUTTERS
EN 779:2012 Particulate air filters for general ventilation - Determination of the filtration performance
ASHRAE HDBK FUNDAMENTALS : 2013 ASHRAE HANDBOOK - FUNDAMENTALS
EN 1506:2007 Ventilation for buildings - Sheet metal air ducts and fittings with circular cross-section - Dimensions
AMCA 210 : 2016 LABORATORY METHODS OF TESTING FANS FOR CERTIFIED AERODYNAMIC PERFORMANCE RATING
ISO 5801:2017 Fans — Performance testing using standardized airways
EN 12237:2003 Ventilation for buildings - Ductwork - Strength and leakage of circular sheet metal ducts
EI Model code of safe practice Part 15:2015 MODEL CODE OF SAFE PRACTICE - PART 15: AREA CLASSIFICATION FOR INSTALLATIONS HANDLING FLAMMABLE FLUIDS
API 505 : 1997 RECOMMENDED PRACTICE FOR CLASSIFICATION OF LOCATIONS FOR ELECTRICAL INSTALLATIONS AT PETROLEUM FACILITIES CLASSIFIED AS CLASS I, ZONE 0, ZONE 1, AND ZONE 2
ISO 12241:2008 Thermal insulation for building equipment and industrial installations Calculation rules
EN 50272-2:2001 Safety requirements for secondary batteries and battery installations - Part 2: Stationary batteries
IEC 60079-0:2011 Explosive atmospheres - Part 0: Equipment - General requirements
ISO 7730:2005 Ergonomics of the thermal environment — Analytical determination and interpretation of thermal comfort using calculation of the PMV and PPD indices and local thermal comfort criteria
EN 1751:2014 Ventilation for buildings - Air terminal devices - Aerodynamic testing of damper and valves
ISO 7235:2003 Acoustics — Laboratory measurement procedures for ducted silencers and air-terminal units — Insertion loss, flow noise and total pressure loss
API 4589 : 1993 Fugitive Hydrocarbon Emissions from Oil and Gas Production Operations
ISO 13702:2015 Petroleum and natural gas industries — Control and mitigation of fires and explosions on offshore production installations — Requirements and guidelines
EN 378-2:2016 Refrigerating systems and heat pumps - Safety and environmental requirements - Part 2: Design, construction, testing, marking and documentation
EN 12451:2012 Copper and copper alloys - Seamless, round tubes for heat exchangers

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.