• There are no items in your cart

I.S. EN ISO 15138:2007

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by

PETROLEUM AND NATURAL GAS INDUSTRIES - OFFSHORE PRODUCTION INSTALLATIONS - HEATING, VENTILATION AND AIR-CONDITIONING

Available format(s)

Hardcopy , PDF

Superseded date

23-07-2013

Language(s)

English

Published date

01-01-2007

For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.

Only cited Standards give presumption of conformance to New Approach Directives/Regulations.


Dates of withdrawal of national standards are available from NSAI.

Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Abbreviated terms
5 Design
  5.1 Introduction
  5.2 Development of design basis
  5.3 System design - General
  5.4 Area-specific system design
  5.5 Equipment and bulk selection
  5.6 Installation and commissioning
Annex A (normative) - Equipment and bulk selection
Annex B (normative) - Installation and commissioning
Annex C (informative) - Operation and maintenance
Annex D (informative) - Datasheets
Annex E (normative) - Standard data for flanges
Bibliography

Defines requirements and provides guidance for design, testing, installation and commissioning of heating, ventilation, air-conditioning and pressurization systems and equipment on all offshore production installations for the petroleum and natural gas industries that are: - new or existing; - normally occupied by personnel or not normally occupied by personnel; - fixed or floating but registered as an offshore production installation.

DocumentType
Standard
Pages
122
PublisherName
National Standards Authority of Ireland
Status
Superseded
SupersededBy
Supersedes

ISO 12499:1999 Industrial fans Mechanical safety of fans Guarding
IEC 60079-10:2002 Electrical apparatus for explosive gas atmospheres - Part 10: Classification of hazardous areas
EN 1886:2007 Ventilation for buildings - Air handling units - Mechanical performance
EN 1507:2006 Ventilation for buildings - Sheet metal air ducts with rectangular section - Requirements for strength and leakage
EN 13053:2006+A1:2011 Ventilation for buildings - Air handling units - Rating and performance for units, components and sections
ISO 3744:2010 Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Engineering methods for an essentially free field over a reflecting plane
EN 1505:1997 Ventilation for buildings - Sheet metal air ducts and fittings with rectangular cross section - Dimensions
NS 5575 : 1ED 1987 VENTILATION DUCTS - IDENTIFICATION COLOURS
NFPA 96 : 2017 VENTILATION CONTROL AND FIRE PROTECTION OF COMMERCIAL COOKING OPERATIONS
EN 378-4:2016 Refrigerating systems and heat pumps - Safety and environmental requirements - Part 4: Operation, maintenance, repair and recovery
ISO 14694:2003 Industrial fans — Specifications for balance quality and vibration levels
EN 378-1:2016 Refrigerating systems and heat pumps - Safety and environmental requirements - Part 1: Basic requirements, definitions, classification and selection criteria
EN 378-3:2016 Refrigerating systems and heat pumps - Safety and environmental requirements - Part 3: Installation site and personal protection
ISO 7547:2002 Ships and marine technology Air-conditioning and ventilation of accommodation spaces Design conditions and basis of calculations
ISO 16812:2007 Petroleum, petrochemical and natural gas industries Shell-and-tube heat exchangers
ISO 5149:1993 Mechanical refrigerating systems used for cooling and heating Safety requirements
ISO 9309:1989 Refrigerant compressors Presentation of performance data
ISO 8861:1998 Shipbuilding — Engine-room ventilation in diesel-engined ships — Design requirements and basis of calculations
ISO 1940-1:2003 Mechanical vibration Balance quality requirements for rotors in a constant (rigid) state Part 1: Specification and verification of balance tolerances
ISO 917:1989 Testing of refrigerant compressors
AMCA 500 : 1994 TEST METHODS FOR LOUVERS, DAMPERS AND SHUTTERS
EN 779:2012 Particulate air filters for general ventilation - Determination of the filtration performance
ASHRAE HDBK FUNDAMENTALS : 2013 ASHRAE HANDBOOK - FUNDAMENTALS
EN 1506:2007 Ventilation for buildings - Sheet metal air ducts and fittings with circular cross-section - Dimensions
AMCA 210 : 2016 LABORATORY METHODS OF TESTING FANS FOR CERTIFIED AERODYNAMIC PERFORMANCE RATING
ISO 5801:2017 Fans — Performance testing using standardized airways
EN 12237:2003 Ventilation for buildings - Ductwork - Strength and leakage of circular sheet metal ducts
EI Model code of safe practice Part 15:2015 MODEL CODE OF SAFE PRACTICE - PART 15: AREA CLASSIFICATION FOR INSTALLATIONS HANDLING FLAMMABLE FLUIDS
API 505 : 1997 RECOMMENDED PRACTICE FOR CLASSIFICATION OF LOCATIONS FOR ELECTRICAL INSTALLATIONS AT PETROLEUM FACILITIES CLASSIFIED AS CLASS I, ZONE 0, ZONE 1, AND ZONE 2
ISO 12241:2008 Thermal insulation for building equipment and industrial installations Calculation rules
EN 50272-2:2001 Safety requirements for secondary batteries and battery installations - Part 2: Stationary batteries
IEC 60079-0:2011 Explosive atmospheres - Part 0: Equipment - General requirements
ISO 7730:2005 Ergonomics of the thermal environment — Analytical determination and interpretation of thermal comfort using calculation of the PMV and PPD indices and local thermal comfort criteria
EN 1751:2014 Ventilation for buildings - Air terminal devices - Aerodynamic testing of damper and valves
ISO 7235:2003 Acoustics — Laboratory measurement procedures for ducted silencers and air-terminal units — Insertion loss, flow noise and total pressure loss
API 4589 : 1993 Fugitive Hydrocarbon Emissions from Oil and Gas Production Operations
ISO 13702:2015 Petroleum and natural gas industries — Control and mitigation of fires and explosions on offshore production installations — Requirements and guidelines
EN 378-2:2016 Refrigerating systems and heat pumps - Safety and environmental requirements - Part 2: Design, construction, testing, marking and documentation
EN 12451:2012 Copper and copper alloys - Seamless, round tubes for heat exchangers

View more information
€149.00
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.