Skip to content
Please enter a keyword to search

  • EN ISO 15876-5:2017

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    Plastics piping systems for hot and cold water installations - Polybutene (PB) - Part 5: Fitness for purpose of the system (ISO 15876-5:2017)

    Available format(s): 

    Superseded date:  08-01-2021

    Language(s): 

    Published date:  08-02-2017

    Publisher:  Comite Europeen de Normalisation

    Pure ENs are not available for sale, please purchase a suitable national adoption

    Sorry this product is not available in your region.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    European foreword
    Foreword
    Introduction
    1 Scope
    2 Normative references
    3 Terms and definitions, symbols and abbreviated terms
    4 Fitness for purpose of the joints and the piping system
    Bibliography

    Abstract - (Show below) - (Hide below)

    ISO 15876-5:2017 specifies the characteristics of the fitness for purpose of polybutene-1 (PB-1) piping systems, intended to be used for hot and cold water installations within buildings for the conveyance of water, whether or not intended for human consumption, (domestic systems) and for heating systems, under design pressures and temperatures according to the class of application (see ISO 15876‑1).The designation polybutene is used together with the abbreviation PB throughout this document.ISO 15876-5:2017 covers a range of service conditions (application classes) and design pressure classes. For values of TD, Tmax and Tmal in excess of those in ISO 15876‑1:2016, Table 1, this document does not apply.NOTE It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.It also specifies the test parameters for the test methods referred to in this document.In conjunction with the other parts of ISO 15876, it is applicable to PB pipes, fittings, their joints and to joints with components of other plastics and non-plastics materials intended to be used for hot and cold water installations.

    General Product Information - (Show below) - (Hide below)

    Committee CEN/TC 155
    Document Type Standard
    Publisher Comite Europeen de Normalisation
    Status Superseded
    Superseded By

    Standards Referenced By This Book - (Show below) - (Hide below)

    DIN EN 1254-6:2012-12 Copper and copper alloys - Plumbing fittings - Part 6: Fittings with push-fit ends
    07/30160794 DC : 0 BS EN 15632-2 - DISTRICT HEATING PIPES - PRE-INSULATED FLEXIBLE PIPE SYSTEMS - PART 2: BONDED PLASTIC SERVICE PIPES - REQUIREMENTS AND TEST METHODS
    PREN 1254-6 : DRAFT 2011 COPPER AND COPPER ALLOYS - PLUMBING FITTINGS - PART 6: FITTING WITH PUSH-FIT ENDS
    I.S. EN 15632-3:2010 DISTRICT HEATING PIPES - PRE-INSULATED FLEXIBLE PIPE SYSTEMS - PART 3: NON BONDED SYSTEM WITH PLASTIC SERVICE PIPES; REQUIREMENTS AND TEST METHODS
    DIN EN 15632-2:2015-03 District heating pipes - Pre-insulated flexible pipe systems - Part 2: Bonded plastic service pipes - Requirements and test methods (includes Amendment A1:2014)
    07/30160797 DC : 0 BS EN 15632-3 - DISTRICT HEATING PIPES - PRE-INSULATED FLEXIBLE PIPE SYSTEMS - PART 3: NON BONDED PLASTIC SERVICE PIPES - REQUIREMENTS AND TEST METHODS
    11/30197617 DC : 0 BS ISO 11855-5 - BUILDING ENVIRONMENT DESIGN - STANDARDS FOR THE DESIGN, CONSTRUCTION AND OPERATION OF RADIANT HEATING AND COOLING SYSTEMS - PART 5: INSTALLATION
    BS EN 15632-3 : 2010 DISTRICT HEATING PIPES - PRE-INSULATED FLEXIBLE PIPE SYSTEMS - PART 3: NON BONDED SYSTEM WITH PLASTIC SERVICE PIPES; REQUIREMENTS AND TEST METHODS
    NF EN 1264-4 : 2010 WATER BASED SURFACE EMBEDDED HEATING AND COOLING SYSTEMS - PART 4: INSTALLATION
    DIN EN 14868:2005-11 PROTECTION OF METALLIC MATERIALS AGAINST CORROSION - GUIDANCE ON THE ASSESSMENT OF CORROSION LIKELIHOOD IN CLOSED WATER CIRCULATION SYSTEMS
    DIN EN 14868 E : 2005 PROTECTION OF METALLIC MATERIALS AGAINST CORROSION - GUIDANCE ON THE ASSESSMENT OF CORROSION LIKELIHOOD IN CLOSED WATER CIRCULATION SYSTEMS
    DIN EN ISO 15876-2:2004-03 PLASTICS PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS - POLYBUTYLENE (PB) - PART 2: PIPES
    I.S. EN 1264-4:2009 WATER BASED SURFACE EMBEDDED HEATING AND COOLING SYSTEMS - PART 4: INSTALLATION
    I.S. EN ISO/TS 15876-7:2004 PLASTICS PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS - POLYBUTYLENE (PB) - PART 7: GUIDANCE FOR THE ASSESSMENT OF CONFORMITY
    11/30213587 DC : 0 BS EN 1254-6 - COPPER AND COPPER ALLOYS - PLUMBING FITTINGS - PART 6: FITTINGS WITH PUSH-FIT ENDS
    07/19990369 DC : 0 BS EN 806-4 - SPECIFICATIONS FOR INSTALLATIONS INSIDE BUILDINGS CONVEYING WATER FOR HUMAN CONSUMPTION - PART 4 - INSTALLATION
    BS EN 15632-2 : 2010 DISTRICT HEATING PIPES - PRE-INSULATED FLEXIBLE PIPE SYSTEMS - PART 2: BONDED PLASTIC SERVICE PIPES - REQUIREMENTS AND TEST METHODS
    EN ISO/TS 15876-7 : 2003 PLASTICS PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS - POLYBUTYLENE (PB) - PART 7: GUIDANCE FOR THE ASSESSMENT OF CONFORMITY
    EN 1264-4:2009 Water based surface embedded heating and cooling systems - Part 4: Installation
    I.S. EN 15632-2:2010 DISTRICT HEATING PIPES - PRE-INSULATED FLEXIBLE PIPE SYSTEMS - PART 2: BONDED PLASTIC SERVICE PIPES - REQUIREMENTS AND TEST METHODS
    ISO/TS 15876-7:2003 Plastics piping systems for hot and cold water installations Polybutylene (PB) Part 7: Guidance for the assessment of conformity
    DIN EN 1264-4:2009-11 Water based surface embedded heating and cooling systems - Part 4: Installation
    BS EN 1264-4:2009 Water based surface embedded heating and cooling systems Installation
    UNI EN 15015 : 2008 PLASTICS PIPING SYSTEMS - SYSTEMS FOR HOT AND COLD WATER NOT INTENDED FOR HUMAN CONSUMPTION - PERFORMANCE CHARACTERISTICS FOR PIPES, FITTINGS AND THEIR JOINTS
    UNI EN 1254-6 : 2012 COPPER AND COPPER ALLOYS - PLUMBING FITTINGS - PART 6: FITTINGS WITH PUSH-FIT ENDS
    UNI EN 1264-4 : 2009 WATER BASED SURFACE EMBEDDED HEATING AND COOLING SYSTEMS - PART 4: INSTALLATION
    I.S. EN 1254-6:2012 COPPER AND COPPER ALLOYS - PLUMBING FITTINGS - PART 6: FITTINGS WITH PUSH-FIT ENDS
    BS EN 14868:2005 Protection of metallic materials against corrosion. Guidance on the assessment of corrosion likelihood in closed water circulation systems
    BS EN 806-2:2005 Specifications for installations inside buildings conveying water for human consumption Design
    EN 14868 : 2005 PROTECTION OF METALLIC MATERIALS AGAINST CORROSION - GUIDANCE ON THE ASSESSMENT OF CORROSION LIKELIHOOD IN CLOSED WATER CIRCULATION SYSTEMS
    EN 806-2:2005 Specification for installations inside buildings conveying water for human consumption - Part 2: Design
    EN 15632-2:2010+A1:2014 (edition 2) District heating pipes - Pre-insulated flexible pipe systems - Part 2: Bonded plastic service pipes - Requirements and test methods
    EN 15632-3:2010+A1:2014 (edition 2) District heating pipes - Pre-insulated flexible pipe systems - Part 3: Non bonded system with plastic service pipes; requirements and test methods
    BS EN 1254-6:2012 Copper and copper alloys. Plumbing fittings Fittings with push-fit ends
    DIN EN 15632-3:2015-03 District heating pipes - Pre-insulated flexible pipe systems - Part 3: Non bonded system with plastic service pipes - Requirements and test methods (includes Amendment A1:2014)
    EN 1254-6:2012 Copper and copper alloys - Plumbing fittings - Part 6: Fittings with push-fit ends
    UNE-EN 1254-6:2013 Copper and copper alloys - Plumbing fittings - Part 6: Fittings with push-fit ends
    07/30168416 DC : 0 BS EN 1264-4 - WATER BASED SURFACE EMBEDDED HEATING AND COOLING SYSTEMS - PART 4: INSTALLATION
    UNI EN 806-2 : 2008 SPECIFICATION FOR INSTALLATIONS INSIDE BUILDINGS CONVEYING WATER FOR HUMAN CONSUMPTION - PART 2: DESIGN
    DD CEN ISO/TS 15876-7:2003 Plastics piping systems for hot and cold water installations. Polybutylene (PB) Guidance for the assessment of conformity
    DIN EN 806-2:2005-06 Specification for installations inside buildings conveying water for human consumption - Part 2: Design
    UNE-EN 1264-4:2010 Water based surface embedded heating and cooling systems - Part 4: Installation

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO 19892:2011 Plastics piping systems Thermoplastics pipes and fittings for hot and cold water Test method for the resistance of joints to pressure cycling
    ISO 1167-2:2006 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 2: Preparation of pipe test pieces
    ISO 13056:2011 Plastics piping systems Pressure systems for hot and cold water Test method for leaktightness under vacuum
    ISO 1167-4:2007 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 4: Preparation of assemblies
    ISO 3501:2015 Plastics piping systems Mechanical joints between fittings and pressure pipes Test method for resistance to pull-out under constant longitudinal force
    ISO 19893:2011 Plastics piping systems Thermoplastics pipes and fittings for hot and cold water Test method for the resistance of mounted assemblies to temperature cycling
    ISO/TS 15876-7:2003 Plastics piping systems for hot and cold water installations Polybutylene (PB) Part 7: Guidance for the assessment of conformity
    ISO 15876-1:2017 Plastics piping systems for hot and cold water installations — Polybutene (PB) — Part 1: General
    ISO 15876-3:2017 Plastics piping systems for hot and cold water installations — Polybutene (PB) — Part 3: Fittings
    ISO 1167-3:2007 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 3: Preparation of components
    CEN/TR 12108:2012 Plastics piping systems - Guidance for the installation inside buildings of pressure piping systems for hot and cold water intended for human consumption
    ISO 15876-2:2017 Plastics piping systems for hot and cold water installations — Polybutene (PB) — Part 2: Pipes
    ISO 3503:2015 Plastics piping systems Mechanical joints between fittings and pressure pipes Test method for leaktightness under internal pressure of assemblies subjected to bending
    ISO 1167-1:2006 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 1: General method
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective