EN ISO 17409:2017
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Electrically propelled road vehicles - Connection to an external electric power supply - Safety requirements (ISO 17409:2015, Corrected version 2015-12-15)
21-03-2020
11-01-2017
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Environmental conditions
5 Requirements for protection of persons
against electric shock
6 Protection against thermal incident
7 Specific requirements for the vehicle inlet,
plug, and cable
8 Additional requirements for a.c. electric
power supply
9 Additional requirements for d.c. electric
power supply
10 Operational requirements
11 Owner's manual and marking
12 Test procedure
Bibliography
ISO 17409:2015 specifies electric safety requirements for conductive connections of electrically propelled road vehicles to an external electric power supply using a plug or vehicle inlet.It applies to electrically propelled road vehicles with voltage class B electric circuits. In general, it may apply to motorcycles and mopeds if no dedicated standards for these vehicles exist.It applies only to vehicle power supply circuits. It applies also to dedicated power supply control functions used for the connection of the vehicle to an external electric power supply.It does not provide requirements regarding the connection to a non-isolated d.c. charging station.It does not provide comprehensive safety information for manufacturing, maintenance, and repair personnel.The requirements when the vehicle is not connected to the external electric power supply are specified in ISO 6469‑3.NOTE 1 This International Standard does not contain requirements for vehicle power supply circuits using protection by class II or double/reinforced insulation but it is not the intention to exclude such vehicle applications.NOTE 2 Requirements for EV supply equipment are specified in IEC 61851.
| Committee |
CEN/TC 301
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| UNE-EN ISO 17409:2017 | Identical |
| ONORM EN ISO 17409 : 2017 | Identical |
| DIN EN ISO 17409:2016-09 (Draft) | Identical |
| DIN EN ISO 17409:2017-07 | Identical |
| ISO 17409:2015 | Identical |
| NF EN ISO 17409 : 2017 | Identical |
| NEN EN ISO 17409 : 2017 | Identical |
| NS EN ISO 17409 : 2017 | Identical |
| I.S. EN ISO 17409:2017 | Identical |
| PN-EN ISO 17409:2017-03 | Identical |
| UNI EN ISO 17409 : 2017 | Identical |
| SS-EN ISO 17409:2017 | Identical |
| SN EN ISO 17409 : 2017 | Identical |
| BS EN ISO 17409:2017 | Identical |
| IEC 60950-1:2005+AMD1:2009+AMD2:2013 CSV | Information technology equipment - Safety - Part 1: General requirements |
| IEC 60364-5-54:2011 | Low-voltage electrical installations - Part 5-54: Selection and erection of electrical equipment - Earthing arrangements and protective conductors |
| IEC 60038:2009 | IEC standard voltages |
| ISO 6469-2:2009 | Electrically propelled road vehicles Safety specifications Part 2: Vehicle operational safety means and protection against failures |
| IEC 60364-4-43:2008 | Low-voltage electrical installations - Part 4-43: Protection for safety - Protection against overcurrent |
| ISO 16750-4:2010 | Road vehicles — Environmental conditions and testing for electrical and electronic equipment — Part 4: Climatic loads |
| IEC 62196-2:2016 | Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 2: Dimensional compatibility and interchangeability requirements for a.c. pin and contact-tube accessories |
| IEC TS 62763:2013 | Pilot function through a control pilot circuit using PWM (pulse width modulation) and a control pilot wire |
| IEC 62196-3:2014 | Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 3: Dimensional compatibility and interchangeability requirements for d.c. and a.c./d.c. pin and contact-tube vehicle couplers |
| IEC 60884-1:2002+AMD1:2006+AMD2:2013 CSV | Plugs and socket-outlets for household and similar purposes - Part1: General requirements |
| ISO 6469-1:2009 | Electrically propelled road vehicles Safety specifications Part 1: On-board rechargeable energy storage system (RESS) |
| ISO 20653:2013 | Road vehicles — Degrees of protection (IP code) — Protection of electrical equipment against foreign objects, water and access |
| IEC 61557-2:2007 | Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. - Equipment for testing, measuring or monitoring of protective measures - Part 2: Insulation resistance |
| IEC 60364-6:2016 | Low voltage electrical installations - Part 6: Verification |
| ISO 6469-3:2011 | Electrically propelled road vehicles Safety specifications Part 3: Protection of persons against electric shock |
| IEC 60309-1:1999+AMD1:2005+AMD2:2012 CSV | Plugs, socket-outlets and couplers for industrial purposes - Part 1: General requirements |
| IEC 61851-1:2017 | Electric vehicle conductive charging system - Part 1: General requirements |
| IEC 60309-2:1999+AMD1:2005+AMD2:2012 CSV | Plugs, socket-outlets and couplers for industrial purposes - Part 2: Dimensional interchangeability requirements for pin and contact-tube accessories |
| IEC 60990:2016 | Methods of measurement of touch current and protective conductor current |
| IEC 60364-5-52:2009 | Low-voltage electrical installations - Part 5-52: Selection and erection of electrical equipment - Wiring systems |
| IEC 62196-1:2014 | Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 1: General requirements |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.