EN ISO 5458:1998
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Geometrical product specifications (GPS) - Geometrical tolerancing - Positional tolerancing (ISO 5458:1998)
04-04-2019
15-12-1998
Foreword
Introduction
1 Scope
2 Normative reference
3 Definitions
4 Establishment of positional tolerances
5 Tolerance combinations
Annex A (informative) - Definitions
Annex B (informative) - Former practice
Annex C (informative) - Relation to the
GPS matrix model
Annex D (informative) - Bibliography
This International Standard describes the principle of positional tolerancing f for the location of regular and irregular features. However for clarity, only regular-shaped features such as holes, bolts, studs or pins, parallel-sided slots, keys and keyways have been shown. Positional tolerancing may also be applied to the location of a point, a straight line, or a plane surface. However, profile tolerancing must be used when lines are not intended to be straight or surfaces are not intended to lie in a plane, see ISO 1660.
| Committee |
CEN/TC 290
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| SN EN ISO 5458 : 1999 | Identical |
| I.S. EN ISO 5458:2018 | Identical |
| NS EN ISO 5458 : 1ED 1999 | Identical |
| NBN EN ISO 5458 : 1999 | Similar to |
| ISO 5458:1998 | Identical |
| BS EN ISO 5458:2018 | Identical |
| PN EN ISO 5458:2018 | Identical |
| NEN EN ISO 5458 : 1999 | Identical |
| PN EN ISO 5458 : 2000 | Identical |
| NF EN ISO 5458 : 1999 | Identical |
| I.S. EN ISO 5458:1999 | Identical |
| NBN EN ISO 5458 : 1999 | Identical |
| DIN EN ISO 5458:2016-08 (Draft) | Identical |
| UNE-EN ISO 5458:1999 | Identical |
| BS EN ISO 5458:1999 | Identical |
| ONORM EN ISO 5458 : 1999 | Identical |
| UNI EN ISO 5458:2018 | Identical |
| UNI EN ISO 5458 : 2001 | Identical |
| DIN EN ISO 5458:2018-11 | Identical |
| ÖNORM EN ISO 5458: 2019 04 01 | Identical |
| NS-EN ISO 5458:2018 | Identical |
| ISO 5458:2018 | Identical |
| DIN CEN ISO/TS 8062-2;DIN SPEC 91184:2014-03 | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - DIMENSIONAL AND GEOMETRICAL TOLERANCES FOR MOULDED PARTS - PART 2: RULES (ISO/TS 8062-2:2013) |
| ISO/TR 14638:1995 | Geometrical product specification (GPS) Masterplan |
| ISO 5459:2011 | Geometrical product specifications (GPS) — Geometrical tolerancing — Datums and datum systems |
| ISO 2692:2014 | Geometrical product specifications (GPS) Geometrical tolerancing Maximum material requirement (MMR), least material requirement (LMR) and reciprocity requirement (RPR) |
| ISO 1101:2017 | Geometrical product specifications (GPS) — Geometrical tolerancing — Tolerances of form, orientation, location and run-out |
| ISO 3098-1:2015 | Technical product documentation Lettering Part 1: General requirements |
| ISO 14660-1:1999 | Geometrical Product Specifications (GPS) Geometrical features Part 1: General terms and definitions |
| ISO 1660:2017 | Geometrical product specifications (GPS) — Geometrical tolerancing — Profile tolerancing |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.