I.S. EN 1057:2006
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
COPPER AND COPPER ALLOYS - SEAMLESS, ROUND COPPER TUBES FOR WATER AND GAS IN SANITARY AND HEATING APPLICATIONS
Hardcopy , PDF
21-07-2006
17-01-2020
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Designations
5 Ordering information
6 Material characteristic
7 Requirements
8 Evaluation of conformity
9 Sampling
10 Test methods
11 Inspection documentation
12 Marking and form of delivery
Annex A (normative) Standardized dimensions for reconsideration
at a future revision
Annex B (normative) Carbon film test
Annex C (normative) Freedom from defects tests
Annex ZA (informative) Clauses of this European Standard
addressing the provisions of the EU
Construction Products Directive (CPD)
89/106/EEC
Annex ZB (informative) Relationship between this European Standard
and the Essential Requirements of the
EU Pressure Equipment Directive (PED)
97/23/EC
Bibliography
Describes the requirements, sampling, test methods and conditions of delivery for seamless round copper tubes.
| DevelopmentNote |
Supersedes I.S. 238. (10/2006) 2006 Edition Re-issued in March 2010 & incorporates AMD 1 2010. (03/2010)
|
| DocumentType |
Standard
|
| Pages |
39
|
| ProductNote |
This standard is Identical to EN 1057: 2006.
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| BS EN 1057 : 2006 | Identical |
| EN 1057:2006+A1:2010 | Identical |
| NS EN 1057 : 2006 + A1 2010 | Identical |
| NF EN 1057 : 2006 + A1 2010 | Identical |
| NEN EN 1057 : 2006 + A1 2010 | Identical |
| NBN EN 1057 : 2006 + A1 2010 | Identical |
| DIN EN 1057:2006-08 | Equivalent |
| EN 1057:2006 | Equivalent |
| UNE-EN 1057:2007 | Identical |
| DIN EN 1057:2010-06 | Identical |
| I.S. 820:2010 | NON-DOMESTIC GAS INSTALLATIONS |
| I.S. 813:2014+A1:2017 | DOMESTIC GAS INSTALLATIONS (EDITION 3) AND AMENDMENT 1:2017 |
| I.S. 813:2014 | DOMESTIC GAS INSTALLATIONS (EDITION 3) AND AMENDMENT 1:2017 |
| I.S. 265:2000 | INSTALLATION OF GAS SERVICE PIPES - PARTS 1 AND 2 (FOURTH EDITION) (INCLUDING AMENDMENT NO. 1) |
| ISO 6507-1:2005 | Metallic materials — Vickers hardness test — Part 1: Test method |
| EN 10002-1 : 2001 | METALLIC MATERIALS - TENSILE TESTING - PART 1: METHOD OF TEST AT AMBIENT TEMPERATURE |
| EN ISO 8494:2013 | Metallic materials - Tube - Flanging test (ISO 8494:2013) |
| EN ISO 8493:2004 | Metallic materials - Tube - Drift-expanding test (ISO 8493:1998) |
| EN 1412:2016 | Copper and copper alloys - European numbering system |
| ISO 1190-1:1982 | Copper and copper alloys — Code of designation — Part 1: Designation of materials |
| ISO 8491:1998 | Metallic materials — Tube (in full section) — Bend test |
| ISO 1553:1976 | Unalloyed copper containing not less than 99,90 % of copper — Determination of copper content — Electrolytic method |
| ISO 8493:1998 | Metallic materials — Tube — Drift-expanding test |
| EN 723:2009 | Copper and copper alloys - Combustion method for determination of the carbon content on the inner surface of copper tubes or fittings |
| ISO 6708:1995 | Pipework components — Definition and selection of DN (nominal size) |
| EN 1971:1998 | Copper and copper alloys - Eddy current test for tubes |
| EN 1173:2008 | Copper and copper alloys - Material condition designation |
| EN ISO 6708:1995 | Pipework components - Definition and selection of DN (nominal size) (ISO 6708:1995) |
| EN ISO 9001:2015 | Quality management systems - Requirements (ISO 9001:2015) |
| ISO 857-1:1998 | Welding and allied processes — Vocabulary — Part 1: Metal welding processes |
| ISO 4741:1984 | Copper and copper alloys — Determination of phosphorus content — Molybdovanadate spectrometric method |
| EN 10204:2004 | Metallic products - Types of inspection documents |
| ISO 9001:2015 | Quality management systems — Requirements |
| EN ISO 8491:2004 | Metallic materials - Tube (in full section) - Bend test (ISO 8491:1998) |
| ISO 8494:2013 | Metallic materials — Tube — Flanging test |
| ISO 857-2:2005 | Welding and allied processes — Vocabulary — Part 2: Soldering and brazing processes and related terms |
Access your standards online with a subscription
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Important note : Users cannot be edited or removed once added to your Multi user PDF.