I.S. EN 12012-4:2006
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
PLASTICS AND RUBBER MACHINES - SIZE REDUCTION MACHINES - PART 4: SAFETY REQUIREMENTS FOR AGGLOMERATORS
Hardcopy , PDF
English
01-01-2006
05-07-2019
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 List of significant hazards
4.1 Mechanical hazard
4.2 Thermal hazards
4.3 Noise hazards
4.4 Hazards generated by dust, fumes and gases
4.5 Hazards due to electrical energy
4.6 Hazards due to unexpected start-up
4.7 Falls from height
5 Safety requirements and/or protective measures
5.1 General
5.2 Mechanical hazard
5.2.1 Access through openings in the agglomerator chamber
5.2.2 Feed material that is not pre-cut
5.2.3 Ejection of parts or materials from the agglomerator
chamber
5.2.4 Strength
5.3 Thermal hazards
5.4 Noise hazards
5.4.1 Noise reduction at source by design
5.4.2 Noise reduction by protective measures
5.4.3 Information connected with noise hazards
5.5 Hazards generated by dust, fumes and gases
5.6 Hazards due to electrical energy
5.6.1 Electrical equipment
5.6.2 Accumulation of electrostatic charges
5.7 Unexpected start-up
5.8 Falls from height
6 Verification of conformity with the safety requirements
and/or protective measures
7 Information for use
7.1 Instruction manual
7.2 Marking
Annex A (normative) Noise test code
A.1 Scope
A.2 Determination of sound power levels
A.2.1 Basic standards
A.2.2 Measurement uncertainty
A.3 Determination of emission sound pressure level at the
workstation(s)
A.3.1 Basic standards
A.3.2 Measurement uncertainty
A.4 Installation and mounting conditions for the noise
measurement
A.5 Operating conditions
A.6 Information to be recorded and reported
A.6.1 General
A.6.2 General agglomerator data
A.6.3 Agglomerator chamber data
A.6.4 Standards
A.6.5 Noise data
A.6.6 Specified test parameters
A.6.7 Installation and operating conditions
A.7 Declaration and verification of noise emission values
Annex ZA (informative) Relationship between this European
Standard and the Essential Requirements of EU
Directive 98/37/EC
Annex ZB (informative) Relationship between this European
Standard and the Essential Requirements of EU
Directive 2006/42/EC
Bibliography
Specifies the essential safety requirements applicable to the design and construction of agglomerators used to densify plastic scrap, reducing its size and/or volume.
| DevelopmentNote |
2006 Edition Re-Issued in October 2008 & incorporates AMD 1 2008. (10/2008)
|
| DocumentType |
Standard
|
| Pages |
24
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| EN 12012-4:2006+A1:2008 | Identical |
| DIN EN 12012-4:2010-01 | Identical |
| NBN EN 12012-4 : 2006 + A1 2008 | Identical |
| NEN EN 12012-4 : 2006 + A1 2008 | Identical |
| NS EN 12012-4 : 2006 + A1 2008 | Identical |
| BS EN 12012-4 : 2006 | Identical |
| NF EN 12012-4 : 2007 + A1 2008 | Identical |
| EN 12012-4:2006 | Equivalent |
| UNE-EN 12012-4:2007 | Identical |
A newer version of this standard is available.
View Current Edition
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : Users cannot be edited or removed once added to your Multi user PDF.