I.S. EN 12977-1:2012
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
THERMAL SOLAR SYSTEMS AND COMPONENTS - CUSTOM BUILT SYSTEMS - PART 1: GENERAL REQUIREMENTS FOR SOLAR WATER HEATERS AND COMBISYSTEMS
Hardcopy , PDF
29-04-2018
English
01-01-2012
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
National Foreword
European foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviations
5 System classification
6 Requirements
Annex A (informative) - Implementation for Ecodesign and
Energy labelling
Annex ZA (informative) - Relationship between this
European Standard and the energy labeling
requirements of Commission Delegated Regulation
(EC) No 811/aimed to be covered
Annex ZB (informative) - Relationship between this European
Standard and the energy labelling requirements of
Commission Delegated Regulation (EC) No 812/
aimed to be covered
Annex ZC (informative) - Relationship between this European
Standard and the ecodesign requirements of
Commission Regulation (EC) No 814/2013 aimed
to be covered
Bibliography
Describes requirements on durability, reliability and safety of small and large custom built solar heating and cooling systems with liquid heat transfer medium in the collector loop for residential buildings and similar applications.
| DevelopmentNote |
Supersedes SR CEN/TS 12977-1. (04/2012)
|
| DocumentType |
Standard
|
| Pages |
23
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| EN 12977-1:2018 | Identical |
| EN 16297-1:2012 | Pumps - Rotodynamic pumps - Glandless circulators - Part 1: General requirements and procedures for testing and calculation of energy efficiency index (EEI) |
| ISO 9459-1:1993 | Solar heating — Domestic water heating systems — Part 1: Performance rating procedure using indoor test methods |
| ISO 9488:1999 | Solar energy Vocabulary |
| EN 1490:2000 | Building valves - Combined temperature and pressure relief valves - Tests and requirements |
| ISO/TR 10217:1989 | Solar energy Water heating systems Guide to material selection with regard to internal corrosion |
| EN 307:1998 | Heat exchangers - Guidelines to prepare installation, operating and maintenance instructions required to maintain the performance of each type of heat exchangers |
| IEC 60335-2-21:2012 | Household and similar electrical appliances - Safety - Part 2-21: Particular requirements for storage water heaters |
| EN 12975-1:2006+A1:2010 | Thermal solar systems and components - Solar collectors - Part 1: General requirements |
| EN 1717:2000 | Protection against pollution of potable water in water installations and general requirements of devices to prevent pollution by backflow |
| EN 15316-4-3:2017 | Energy performance of buildings - Method for calculation of system energy requirements and system efficiencies - Part 4-3: Heat generation systems, thermal solar and photovoltaic systems, Module M3-8-3, M8-8-3, M11-8-3 |
| ISO 9806:2017 | Solar energy — Solar thermal collectors — Test methods |
| EN 62305-4:2011/AC:2016-11 | Protection against lightning - Part 4: Electrical and electronic systems within structures |
| IEC 62305-1:2010 | Protection against lightning - Part 1: General principles |
| EN 60335-2-21:2003/corrigendum Oct. 2010 | HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 2-21: PARTICULAR REQUIREMENTS FOR STORAGE WATER HEATERS |
| EN ISO 9488:1999 | Solar energy - Vocabulary (ISO 9488:1999) |
| EN 12976-2:2017 | Thermal solar systems and components - Factory made systems - Part 2: Test methods |
| EN 809 : 1998 COR 2010 | PUMPS AND PUMP UNITS FOR LIQUIDS - COMMON SAFETY REQUIREMENTS |
| EN 12897:2016 | Water supply - Specification for indirectly heated unvented (closed) storage water heaters |
| EN 806-2:2005 | Specification for installations inside buildings conveying water for human consumption - Part 2: Design |
| EN 1489:2000 | Building valves - Pressure safety valves - Tests and requirements |
| EN 12828:2012+A1:2014 | Heating systems in buildings - Design for water-based heating systems |
| EN 60335-1:2012/A13:2017 | HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 1: GENERAL REQUIREMENTS (IEC 60335-1:2010, MODIFIED) |
| EN 253:2009+A2:2015 | District heating pipes - Preinsulated bonded pipe systems for directly buried hot water networks - Pipe assembly of steel service pipe, polyurethane thermal insulation and outer casing of polyethylene |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.