I.S. EN 13244-1:2002
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
PLASTICS PIPING SYSTEMS FOR BURIED AND ABOVE-GROUND PRESSURE SYSTEMS FOR WATER FOR GENERAL PURPOSES DRAINAGE AND SEWERAGE - POLYETHYLENE (PE) - GENERAL
Hardcopy , PDF
14-09-2011
English
01-01-2002
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Foreword
Introduction
1 Scope
2 Normative references
3 Definitions, symbols and abbreviations
3.1 Terms and definitions
3.1.1 Geometrical definitions
3.1.2 Definitions related to service conditions
3.1.3 Definitions related to material
characteristics
3.2 Symbols
3.3 Abbreviations
4 Material
4.1 Compound
4.2 Colour
4.2.1 General
4.2.2 Black compound
4.3 Use of reprocessable and recyclable material
4.4 Physical characteristics of the compound
4.5 Fusion compatibility
4.6 Classification and designation
Annex A (informative) Pressure reduction coefficients
Bibliography
Provides the general aspects of polyethylene (PE) piping systems intended for buried and above-ground pressure systems for water for general purposes, drainage and sewerage.
| DocumentType |
Standard
|
| Pages |
18
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| NF EN 13244-1 : 2003 | Identical |
| SN EN 13244-1 : 2003 | Identical |
| BS EN 13244-1:2002 | Identical |
| NEN EN 13244-1 : 2003 | Identical |
| NS EN 13244-1 : 1ED 2002 | Identical |
| UNI EN 13244-1 : 2004 | Identical |
| EN 13244-1:2002 | Identical |
| NBN EN 13244-1 : 2003 | Identical |
| DIN EN 13244-1:2003-04 | Identical |
| EN ISO 12162:2009 | Thermoplastics materials for pipes and fittings for pressure applications - Classification, designation and design coefficient (ISO 12162:2009) |
| ISO 13953:2001 | Polyethylene (PE) pipes and fittings — Determination of the tensile strength and failure mode of test pieces from a butt-fused joint |
| EN 12118:1997 | Plastics piping systems - Determination of moisture content in thermoplastics by coulometry |
| EN 728:1997 | Plastics piping and ducting systems - Polyolefin pipes and fittings - Determination of oxidation induction time |
| ISO 6964:1986 | Polyolefin pipes and fittings Determination of carbon black content by calcination and pyrolysis Test method and basic specification |
| ISO 13477:2008 | Thermoplastics pipes for the conveyance of fluids — Determination of resistance to rapid crack propagation (RCP) — Small-scale steady-state test (S4 test) |
| ISO 3:1973 | Preferred numbers Series of preferred numbers |
| ISO 18553:2002 | Method for the assessment of the degree of pigment or carbon black dispersion in polyolefin pipes, fittings and compounds |
| EN ISO 13478:2007 | Thermoplastics pipes for the conveyance of fluids - Determination of resistance to rapid crack propagation (RCP) - Full-scale test (FST) (ISO 13478:2007) |
| EN ISO 13479:2009 | Polyolefin pipes for the conveyance of fluids - Determination of resistance to crack propagation - Test method for slow crack growth on notched pipes (ISO 13479:2009) |
| ISO 11414:2009 | Plastics pipes and fittings Preparation of polyethylene (PE) pipe/pipe or pipe/fitting test piece assemblies by butt fusion |
| ISO 1183:1987 | Plastics Methods for determining the density and relative density of non-cellular plastics |
| ISO 11922-1:1997 | Thermoplastics pipes for the conveyance of fluids — Dimensions and tolerances — Part 1: Metric series |
| ISO 472:2013 | Plastics — Vocabulary |
| EN 1056 : 1996 | METHODS OF TESTING PLASTICS - THERMOPLASTICS PIPES, FITTINGS AND VALVES - PLASTICS PIPING AND DUCTING SYSTEMS - PLASTICS PIPES AND FITTINGS - METHOD FOR EXPOSURE TO DIRECT (NATURAL) WEATHERING |
| ISO 4065:1996 | Thermoplastics pipes Universal wall thickness table |
| ISO 497:1973 | Guide to the choice of series of preferred numbers and of series containing more rounded values of preferred numbers |
| ISO 13761:2017 | Plastics pipes and fittings — Pressure reduction factors for polyethylene pipeline systems for use at temperatures above 20 degrees C |
| EN ISO 1133:2005 | Plastics - Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics (ISO 1133:2005) |
| ISO 760:1978 | Determination of water Karl Fischer method (General method) |
| EN 12107 : 1997 | PLASTICS PIPING SYSTEM - INJECTION MOULDED THERMOPLASTICS FITTINGS, VALVES AND ANCILLARY EQUIPMENT - DETERMINATION OF THE LONG-TERM HYDROSTATIC STRENGTH OF THERMOPLASTICS MATERIALS FOR INJECTION MOULDING OF PIPING COMPONENTS |
| ISO 1043-1:2011 | Plastics — Symbols and abbreviated terms — Part 1: Basic polymers and their special characteristics |
| ISO/TR 9080:1992 | Thermoplastics pipes for the transport of fluids — Methods of extrapolation of hydrostatic stress rupture data to determine the long-term hydrostatic strength of thermoplastics pipe materials |
| EN 12099:1997 | Plastics piping systems - Polyethylene piping materials and components - Determination of volatile content |
| EN 13244-2:2002 | Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage - Polyethylene (PE) - Part 2: Pipes |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.