I.S. EN 13244-4:2002
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
PLASTICS PIPING SYSTEMS FOR BURIED AND ABOVE-GROUND PRESSURE SYSTEMS FOR WATER FOR GENERAL PURPOSES DRAINAGE AND SEWERAGE - POLYETHYLENE (PE) - VALVES
Hardcopy , PDF
10-02-2012
English
01-01-2002
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Foreword
Introduction
1 Scope
2 Normative references
3 Definitions, symbols and abbreviations
4 Material
4.1 Compound for PE valve bodies
4.2 Material for non-polyethylene parts
5 General characteristics
5.1 Appearance of the valve
5.2 Design
5.3 Colour
6 Geometrical characteristics
6.1 General
6.2 Measurement of dimensions
6.3 Wall thickness at any point of the PE valve body
6.4 Dimensions of spigot ends for valves
6.5 Dimensions of valves with electrofusion sockets
6.6 Dimensions of the operating cap
7 Mechanical characteristics for assembled valves
7.1 General
7.2 Conditioning
7.3 Requirements
7.4 Retest in case of failure of hydrostatic strength
at 80 degree C
8 Physical characteristics
8.1 Conditioning
8.2 Requirements
9 Performance requirements
10 Marking
10.1 General
10.2 Marking on valves
10.3 Marking on a label
11 Packaging
Bibliography
Provides the characteristics of valves or valve bodies made from polyethylene (PE) intended for buried and above-ground pressure systems for water for general purposes, drainage and sewerage.
| DocumentType |
Standard
|
| Pages |
19
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| UNE-EN 13244-4:2003 | Identical |
| SN EN 13244-4 : 2003 | Identical |
| BS EN 13244-4:2002 | Identical |
| NEN EN 13244-4 : 2003 | Identical |
| NS EN 13244-4 : 1ED 2003 | Identical |
| NBN EN 13244-4 : 2003 | Identical |
| UNI EN 13244-4 : 2004 | Identical |
| EN 13244-4:2002 | Identical |
| NF EN 13244-4 : 2003 | Identical |
| DIN EN 13244-4:2003-04 | Identical |
| EN 13244-1:2002 | Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage - Polyethylene (PE) - Part 1: General |
| EN 1705:1996 | Plastics piping systems - Thermoplastics valves - Test method for the integrity of a valve after an external blow |
| EN 728:1997 | Plastics piping and ducting systems - Polyolefin pipes and fittings - Determination of oxidation induction time |
| EN 28233:1990 | Thermoplastics valves - Torque - Test method (ISO 8233:1988) |
| EN 12100:1997 | Plastics piping systems - Polyethylene (PE) valves - Test method for resistance to bending between supports |
| EN 1074-1:2000 | Valves for water supply - Fitness for purpose requirements and appropriate verification tests - Part 1: General requirements |
| EN 1680:1997 | Plastics piping systems - Valves for polyethylene (PE) piping systems - Test method for leaktightness under and after bending applied to the operating mechanisms |
| ISO 10933:1997 | Polyethylene (PE) valves for gas distribution systems |
| EN 13244-3:2002 | Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage - Polyethylene (PE) - Part 3: Fittings |
| PREN ISO 3126 : DRAFT 1999 | PLASTICS PIPING SYSTEMS - PLASTICS PIPING COMPONENTS - MEASUREMENT AND DETERMINATION OF DIMENSIONS |
| EN 917:1997 | Plastics piping systems - Thermoplastics valves - Test methods for resistance to internal pressure and leaktightness |
| EN ISO 1133:2005 | Plastics - Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics (ISO 1133:2005) |
| EN 13244-5:2002 | Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage - Polyethylene (PE) - Part 5: Fitness for purpose of the system |
| EN 13244-2:2002 | Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage - Polyethylene (PE) - Part 2: Pipes |
| ISO 5208:2015 | Industrial valves Pressure testing of metallic valves |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.