I.S. EN 1349:2009
Current
The latest, up-to-date edition.
INDUSTRIAL PROCESS CONTROL VALVES
Hardcopy , PDF
English
01-01-2009
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviations
5 Requirements
6 Test procedure
7 Dead band test
8 Inspection
9 Designation
10 Marking and preparation for transportation
Annex ZA (informative) - Relationship between
this European Standard
and the Essential
Requirements of EU
Directive 97/23/EC
Bibliography
Describes the design and performance requirements including material, pressure/temperature ratings, dimensions, testing and marking.
| DocumentType |
Standard
|
| Pages |
19
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Current
|
| Supersedes |
| Standards | Relationship |
| UNI EN 1349 : 2010 | Identical |
| UNE-EN 1349:2010 | Identical |
| BS EN 1349:2009 | Identical |
| SN EN 1349 : 2010 | Identical |
| EN 1349:2009 | Identical |
| NBN EN 1349 : 2010 | Identical |
| NS EN 1349 : 2009 | Identical |
| NEN EN 1349 : 2009 | Identical |
| NF EN 1349 : 2009 | Identical |
| EN 12982:2009 | Industrial valves - End-to-end and centre-to-end dimensions for butt welding end valves |
| EN 60534-1:2005 | Industrial-process control valves - Part 1: Control valve terminology and general considerations |
| EN 1759-1:2004 | Flanges and their joint - Circular flanges for pipes, valves, fittings and accessories, Class designated - Part 1: Steel flanges, NPS 1/2 to 24 |
| EN 60534-9 : 2007 | INDUSTRIAL-PROCESS CONTROL VALVES - PART 9: TEST PROCEDURE FOR RESPONSE MEASUREMENTS FROM STEP INPUTS |
| EN 60534-2-4 : 2009 | INDUSTRIAL-PROCESS CONTROL VALVES - PART 2-4: FLOW CAPACITY - INHERENT FLOW CHARACTERISTICS AND RANGEABILITY |
| EN 558:2017 | Industrial valves - Face-to-face and centre-to-face dimensions of metal valves for use in flanged pipe systems - PN and Class designated valves |
| EN 12516-1:2014 | Industrial valves - Shell design strength - Part 1: Tabulation method for steel valve shells |
| EN 12516-4:2014 | Industrial valves - Shell design strength - Part 4: Calculation method for valve shells manufactured in metallic materials other than steel |
| EN 60534-2-5:2003 | Industrial-process control valves - Part 2-5: Flow capacity - Sizing equations for fluid flow through multistage control valves with interstage recovery |
| EN 736-2:2016 | Valves - Terminology - Part 2: Definition of components of valves |
| EN ISO 228-1:2003 | Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions, tolerances and designation (ISO 228-1:2000) |
| EN 12266-1:2012 | Industrial valves - Testing of metallic valves - Part 1: Pressure tests, test procedures and acceptance criteria - Mandatory requirements |
| IEC 60534-2-5:2003 | Industrial-process control valves - Part 2-5: Flow capacity - Sizing equations for fluid flow through multistage control valves with interstage recovery |
| ASME B1.20.1 : 2013(R2018) | PIPE THREADS, GENERAL PURPOSE (INCH) |
| EN 60534-4 : 2006 | Industrial-process control valves - Part 4: Inspection and routine testing |
| IEC 60534-9:2007 | Industrial-process control valves - Part 9: Test procedure for response measurements from step inputs |
| EN 60534-2-1:2011/AC:2015 | INDUSTRIAL-PROCESS CONTROL VALVES - PART 2-1: FLOW CAPACITY - SIZING EQUATIONS FOR FLUID FLOW UNDER INSTALLED CONDITIONS (IEC 60534-2-1:2011) |
| IEC 60534-4:2006 | Industrial-process control valves - Part 4: Inspection and routine testing |
| EN 60534-2-3:2016 | Industrial-process control valves - Part 2-3: Flow capacity - Test procedures |
| EN 60534-5:2004 | Industrial-process control valves - Part 5: Marking |
| IEC 60534-2-3:2015 | Industrial-process control valves - Part 2-3: Flow capacity - Test procedures |
| EN 12760:2016 | Industrial valves - Socket welding ends for steel valves |
| IEC 60534-7:2010 | Industrial-process control valves - Part 7: Control valve data sheet |
| EN 12516-2:2014 | Industrial valves - Shell design strength - Part 2: Calculation method for steel valve shells |
| IEC 60534-2-1:2011 | Industrial-process control valves - Part 2-1: Flow capacity - Sizing equations for fluid flow under installed conditions |
| EN 1092-2:1997 | Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, PN designated - Part 2: Cast iron flanges |
| EN 10226-1:2004 | Pipe threads where pressure tight joints are made on the threads - Part 1: Taper external threads and parallel internal threads - Dimensions, tolerances and designation |
| EN 19:2016 | Industrial valves - Marking of metallic valves |
| IEC 60534-1:2005 | Industrial-process control valves - Part 1: Control valve terminology and general considerations |
| IEC 60534-5:2004 | Industrial-process control valves - Part 5: Marking |
| ISO 228-1:2000 | Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation |
| EN 736-3:2008 | Valves - Terminology - Part 3: Definition of terms |
| IEC 60534-2-4:2009 | Industrial-process control valves - Part 2-4: Flow capacity - Inherent flow characteristics and rangeability |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.