I.S. EN 13799:2012
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
LPG EQUIPMENT AND ACCESSORIES - CONTENTS GAUGES FOR LIQUEFIED PETROLEUM GAS (LPG) PRESSURE VESSELS
Hardcopy , PDF
09-12-2022
English
01-01-2012
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Operating conditions
5 Materials
6 Design - General requirements
7 Design - Specific requirements
8 Design testing
9 Production testing and inspection
10 Marking
11 Documentation
Annex A (normative) - Float gauge flange and gasket
dimensions
Annex B (normative) - Special low temperature
requirements
Annex C (normative) - Production testing and inspection
Annex D (informative) - Vibration Testing
Annex E (informative) - Environment checklist
Bibliography
Describes minimum requirements for design and testing of contents gauges, which are directly connected to LPG transportable pressure vessels, LPG drums, LPG cylinders and static LPG pressure vessels above 0,5 l water capacity excluding those used for automotive containers.
| DocumentType |
Standard
|
| Pages |
30
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| UNI EN 13799 : 2012 | Identical |
| SN EN 13799 : 2012 | Identical |
| NF EN 13799 : 2012 | Identical |
| DIN EN 13799:2012-06 | Identical |
| BS EN 13799:2012 | Identical |
| NEN EN 13799 : 2012 | Identical |
| EN 13799:2012 | Identical |
| NBN EN 13799 : 2012 | Identical |
| NS EN 13799 : 2012 | Identical |
| UNE-EN 13799:2012 | Identical |
| ONORM EN 13799 : 2012 | Identical |
| I.S. 3216:2010 | CODE OF PRACTICE - BULK STORAGE OF LIQUEFIED PETROLEUM GAS (LPG) - (EDITION 2) |
| ISO 11114-1:2012 | Gas cylinders Compatibility of cylinder and valve materials with gas contents Part 1: Metallic materials |
| EN 1503-4:2016 | Valves - Materials for bodies, bonnets and covers - Part 4: Copper alloys specified in European Standards |
| EN 10270-3:2011 | Steel wire for mechanical springs - Part 3: Stainless spring steel wire |
| EN 13906-1:2013 | Cylindrical helical springs made from round wire and bar - Calculation and design - Part 1 : Compression springs |
| EN 60079-0:2012/A11:2013 | EXPLOSIVE ATMOSPHERES - PART 0: EQUIPMENT - GENERAL REQUIREMENTS (IEC 60079-0:2011, MODIFIED) |
| MIL-STD-810 Revision G:2008 | ENVIRONMENTAL ENGINEERING CONSIDERATIONS AND LABORATORY TESTS |
| EN 1503-2:2000 | Valves - Materials for bodies, bonnets and covers - Part 2: Steels other than those specified in European Standards |
| EN 751-2:1996 | Sealing materials for metallic threaded joints in contact with 1st, 2nd and 3rd family gases and hot water - Part 2: Non-hardening jointing compounds |
| EN 1503-1:2000 | Valves - Materials for bodies, bonnets and covers - Part 1: Steels specified in European Standards |
| ASME B1.20.1 : 2013(R2018) | PIPE THREADS, GENERAL PURPOSE (INCH) |
| ISO 7-1:1994 | Pipe threads where pressure-tight joints are made on the threads Part 1: Dimensions, tolerances and designation |
| ISO 11114-2:2013 | Gas cylinders Compatibility of cylinder and valve materials with gas contents Part 2: Non-metallic materials |
| EN ISO 11114-2:2013 | Gas cylinders - Compatibility of cylinder and valve materials with gas contents - Part 2: Non-metallic materials (ISO 11114-2:2013) |
| EN 751-1:1996 | Sealing materials for metallic threaded joints in contact with 1st, 2nd and 3rd family gases and hot water - Part 1: Anaerobic jointing compounds |
| EN 1563:2011 | Founding - Spheroidal graphite cast irons |
| EN 12420:2014 | Copper and copper alloys - Forgings |
| EN 549:1994 | Rubber materials for seals and diaphragms for gas appliances and gas equipment |
| EN 12165:2016 | Copper and copper alloys - Wrought and unwrought forging stock |
| ISO 301:2006 | Zinc alloy ingots intended for castings |
| ISO 6957:1988 | Copper alloys Ammonia test for stress corrosion resistance |
| ISO 1817:2015 | Rubber, vulcanized or thermoplastic Determination of the effect of liquids |
| 1994/9/EC : 1994 | DIRECTIVE 94/9/EC OF THE EUROPEAN PARLIAMENT AND THE COUNCIL OF 23 MARCH 1994 ON THE APPROXIMATION OF THE LAWS OF THE MEMBER STATES CONCERNING EQUIPMENT AND PROTECTIVE SYSTEMS INTENDED FOR USE IN POTENTIALLY EXPLOSIVE ATMOSPHERES |
| 1997/23/EC : 1997 | DIRECTIVE 97/23/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 29 MAY 1997 ON THE APPROXIMATION OF THE LAWS OF THE MEMBER STATES CONCERNING PRESSURE EQUIPMENT |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.