I.S. EN 14593-1:2005
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
RESPIRATORY PROTECTIVE DEVICES - COMPRESSED AIR LINE BREATHING DEVICES WITH DEMAND VALVE - PART 1: DEVICES WITH A FULL FACE MASK - REQUIREMENTS, TESTING AND MARKING
Hardcopy , PDF
05-10-2018
English
01-01-2005
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
National Foreword
European foreword
1 Scope
2 Normative references
3 Terms, description and symbols
4 Requirements
5 Testing
6 Marking
7 Information supplied by the manufacturer
Annex ZA (informative) - Relationship between
this European Standard and the essential
health and safety requirements of Regulation
2016/425/EU [2016 OJ L81] aimed to be covered
Bibliography
Describes minimum requirements for compressed air line breathing apparatus with demand valve for use with a full face mask as a respiratory protective device.
| DevelopmentNote |
Together with I.S. EN 14593-2 supersedes I.S. EN 139. (06/2005)
|
| DocumentType |
Standard
|
| Pages |
37
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| NS EN 14593-1 : 1ED 2005 | Identical |
| ONORM EN 14593-1 : 2005 | Identical |
| SN EN 14593-1 : 2005 | Identical |
| UNE-EN 14593-1:2005 | Identical |
| NBN EN 14593-1 : 2005 | Identical |
| BS EN 14593-1:2005 | Identical |
| UNI EN 14593-1 : 2005 | Identical |
| DIN EN 14593-1:2005-07 | Identical |
| NF EN 14593-1 : 2005 | Identical |
| EN 14593-1:2018 | Identical |
| EN 60812:2006 | Analysis techniques for system reliability - Procedure for failure mode and effects analysis (FMEA) |
| EN 60079-32-2:2015 | Explosive atmospheres - Part 32-2: Electrostatics hazards - Tests |
| EN 148-3:1999 | Respiratory protective devices - Threads for facepieces - Part 3: Tread connection M 45 x 3 |
| EN 12021:2014 | Respiratory equipment - Compressed gases for breathing apparatus |
| IEC 60812:2006 | Analysis techniques for system reliability - Procedure for failure mode and effects analysis (FMEA) |
| EN ISO 8031:2009 | Rubber and plastics hoses and hose assemblies - Determination of electrical resistance and conductivity (ISO 8031:2009) |
| EN 132:1998 | Respiratory protective devices - Definitions of terms and pictograms |
| EN 13274-3:2001 | Respiratory protective devices - Methods of test - Part 3: Determination of breathing resistance |
| EN 134:1998 | Respiratory protective devices - Nomenclature of components |
| EN 13274-4:2001 | Respiratory protective devices - Methods of test - Part 4: Flame tests |
| EN 13274-6:2001 | Respiratory protective devices - Methods of test - Part 6: Determination of carbon dioxide content of the inhalation air |
| ISO 16900-14:2015 | Respiratory protective devices Methods of test and test equipment Part 14: Measurement of sound level |
| EN 13274-1:2001 | Respiratory protective devices - Methods of test - Part 1: Determination of inward leakage and total inward leakage |
| EN 137:2006 | Respiratory protective devices - Self-contained open-circuit compressed air breathing apparatus with full face mask - Requirements, testing, marking |
| EN 148-2:1999 | Respiratory protective devices - Threads for facepieces - Part 2: Centre thread connection |
| ISO 13301:2002 | Sensory analysis Methodology General guidance for measuring odour, flavour and taste detection thresholds by a three-alternative forced-choice (3-AFC) procedure |
| EN 13274-2:2001 | Respiratory protective devices - Methods of test - Part 2: Practical performance tests |
| EN 402:2003 | Respiratory protective devices - Lung governed demand self-contained open-circuit compressed air breathing apparatus with full face mask or mouthpiece assembly for escape - Requirements, testing, marking |
| ISO 8031:2009 | Rubber and plastics hoses and hose assemblies Determination of electrical resistance and conductivity |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.