I.S. EN 14652:2006
Withdrawn
A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.
View Superseded by
WATER CONDITIONING EQUIPMENT INSIDE BUILDINGS - MEMBRANE SEPARATION DEVICES - REQUIREMENTS FOR PERFORMANCE, SAFETY AND TESTING
Hardcopy , PDF
11-07-2007
English
12-04-2006
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Classification
5 Symbols and abbreviations
6 Construction requirements
6.1 General
6.2 Materials
6.3 Resistance to temperature
6.4 Resistance to hydrostatic pressure
6.5 Resistance to cyclic pressure
6.6 Backflow prevention
6.7 Electrical safety
6.8 Noise level
6.9 Air vent
6.10 End connections
6.11 Drain connections
6.12 Component replacement
6.13 Back-washable modules (MF and UF)
7 Performance requirements
7.1 General
7.2 Hydraulic performance (applicable to MF, UF)
7.3 Mechanical performance
7.4 Functional performance
8 Instruction and information
8.1 Installation, operation and maintenance instructions
- Instruction manual
8.2 Marking and data plate
8.3 Performance data sheet
Annex A (normative) Test methods
Annex B (informative) Types of membrane
Annex C (informative) Typical test reports
Annex D (normative) Installation, operation and maintenance
Bibliography
Specifies requirements relating to the construction, performance and methods of testing for membrane separation systems with a particle rating below 1 [mu]m, namely microfiltration (MF), ultrafiltration (UF), nanofiltration (NF) and reverse osmosis (RO) for drinking water installations inside buildings, intended to remove from the drinking water marginal concentrations of suspended and colloidal solids, microorganisms, organic molecules and/or to reduce the dissolved solids concentration and applies to systems with a minimum pressure of PN 10, connections between DN 15 and DN 100 and a maximum working temperature of at least 30 degrees C.
| DevelopmentNote |
2006 Edition Re-Issued in July 2007 & incorporates AMD 1 2007. (07/2007)
|
| DocumentType |
Standard
|
| Pages |
58
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Withdrawn
|
| SupersededBy |
| Standards | Relationship |
| UNI EN 14652 : 2007 | Identical |
| SN EN 14652 : 2005 + A1 2007 | Identical |
| NEN EN 14652 : 2006 + A1 2007 | Identical |
| NBN EN 14652 : 2006 + A1 2007 | Identical |
| UNE-EN 14652:2006 | Identical |
| BS EN 14652 : 2005 | Identical |
| EN 14652:2005+A1:2007 | Identical |
| NS EN 14652 : 2005 + A1 2007 | Identical |
| NF EN 14652 : 2006 + A1 2007 | Identical |
| DIN EN 14652:2007-09 | Identical |
| EN 27888:1993 | Water quality - Determination of electrical conductivity (ISO 7888:1985) |
| EN 1254-1:1998 | Copper and copper alloys - Plumbing fittings - Part 1: Fittings with ends for capillary soldering or capillary brazing to copper tubes |
| EN 13443-2:2005+A1:2007 | Water conditioning equipment inside buildings - Mechanical filters - Part 2: Particle rating 1 µm to less than 80 µm - Requirements for performance, safety and testing |
| EN ISO 7027:1999 | Water quality - Determination of turbidity (ISO 7027:1999) |
| EN 15161:2006 | Water conditioning equipment inside buildings - Installation, operation, maintenance and repair |
| EN 1567:1999 | Building valves - Water pressure reducing valves and combination water pressure reducing valves - Requirements and tests |
| EN 1717:2000 | Protection against pollution of potable water in water installations and general requirements of devices to prevent pollution by backflow |
| ISO 6708:1995 | Pipework components Definition and selection of DN (nominal size) |
| EN ISO 6708:1995 | Pipework components - Definition and selection of DN (nominal size) (ISO 6708:1995) |
| EN ISO 228-1:2003 | Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions, tolerances and designation (ISO 228-1:2000) |
| ISO 7-1:1994 | Pipe threads where pressure-tight joints are made on the threads Part 1: Dimensions, tolerances and designation |
| ISO 7888:1985 | Water quality — Determination of electrical conductivity |
| ISO 1219-1:2012 | Fluid power systems and components — Graphical symbols and circuit diagrams — Part 1: Graphical symbols for conventional use and data-processing applications |
| ISO 3696:1987 | Water for analytical laboratory use — Specification and test methods |
| EN ISO 3696:1995 | Water for analytical laboratory use - Specification and test methods (ISO 3696:1987) |
| ISO 12103-1:2016 | Road vehicles — Test contaminants for filter evaluation — Part 1: Arizona test dust |
| ISO 10523:2008 | Water quality — Determination of pH |
| EN 1092-2:1997 | Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, PN designated - Part 2: Cast iron flanges |
| ISO 228-1:2000 | Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation |
| ISO 7027:1999 | Water quality Determination of turbidity |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.