I.S. EN 14944-3:2007

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and Definitions
4 Principle
5 Reagents
   5.1 General requirements
   5.2 Disinfection reagents
        5.2.1 Sodium hypochlorite solution
        5.2.2 Disinfection treatment water
   5.3 Waters to be used for testing
        5.3.1 Preconditioning water
        5.3.2 Test water
        5.3.3 Test water without chlorine content (chlorine-free)
        5.3.4 Test water with chlorine content (chlorinated)
   5.4 Cleaning liquids for apparatus
6 Apparatus
   6.1 General
   6.2 Apparatus and materials for test piece preparation
        6.2.1 Stainless steel plates and cylinders
        6.2.2 Glass cylinders
        6.2.3 Moulds for forming test pieces
   6.3 Apparatus and materials for preconditioning and
        migration procedure
        6.3.1 Vessels, containers, covers, connectors and stoppers
7 Samples and test pieces
   7.1 Sampling, transport and storage of samples
   7.2 Preparation of test pieces
        7.2.1 General
        7.2.2 Factory made pipes, fittings and storage systems
   7.3 Surface area-to-volume ratio (S/V) for use in the
        test procedure
        7.3.1 General
        7.3.2 Pipes and fittings
        7.3.3 Storage systems (cement mortar, cement
              mortar lined or concrete)
8 Pre-treatment of samples (curing, preconditioning and
   disinfection)
   8.1 General
   8.2 Curing
   8.3 Preconditioning
        8.3.1 General
        8.3.2 Preconditioning without disinfection treatment
        8.3.3 Preconditioning with disinfection treatment
9 Test procedure
   9.1 General
   9.2 Preparation of migration water for analysis of substances
        9.2.2 Second and third migration periods
        9.2.3 Additional migration periods
   9.3 Control samples (blank test)
10 Analysis
11 Calculation of test results
   11.1 Calculation of the concentration of the
        substances in the migration water
   11.2 Calculation of the migration rate of the measured
        substances
   11.3 Calculation of the mean migration rate
12 Test report
   12.1 General information
   12.2 Information on the product
   12.3 Information on the test procedure
   12.4 Test results
Annex A (normative) - Additional procedures for testing
                      factory made pipes (cement mortar
                      lined and concrete)
         A.1 Sampling, test piece preparation and storage
             A.1.1 Sampling
             A.1.2 Test piece preparation and storage
         A.2 Surface area to volume (S/V) ratio
         A.3 Pretreatment of test pieces
             (preconditioning and disinfection)
         A.4 Test procedure
             A.4.1 Migration procedure at 23 degree C
             A.4.2 Migration procedure at elevated temperature
         A.5 Expression of results
         A.6 Reporting
Annex B (normative) - Additional procedures for testing
                      factory made fittings (cement mortar
                      lined and concrete)
         B.1 Sampling, test piece preparation and storage
             B.1.1 Sampling of Factory made fittings
             B.1.2 Test piece preparation and storage
         B.2 Surface area to volume (S/V) ratio
         B.3 Pre-treatment of test pieces
             (preconditioning and disinfection)
         B.4 Test procedure
             B.4.1 Migration procedure at 23 degree C
             B.4.2 Migration procedure at elevated temperature
         B.5 Expression of results
         B.6 Reporting
Annex C (normative) - Additional procedures for testing
                      factory made storage systems (cement
                      mortar, cement mortar lined and concrete)
         C.1 Sampling, test piece preparation and storage
             C.1.1 Sampling
             C.1.2 Test piece preparation and storage
         C.2 Surface area to volume (S/V) ratio
         C.3 Pretreatment of test pieces
             (preconditioning and disinfection)
         C.4 Test procedure
             C.4.1 Migration procedure at 23 degree C
             C.4.2 Migration procedure at elevated temperature
         C.5 Expression of results
         C.6 Reporting
Annex D (informative) - Examples of typical test pieces
                        and test conditions as a function
                        of S/V ratio
         D.1 General
         D.2 Pipes and fittings
         D.3 Test pieces to which a cylinder of stainless
             steel or glass is to be attached
         D.4 Square test plates coated with mortar
         D.5 Moulded test pieces where all faces
             are exposed to test water
Annex E (informative) - Test arrangements for testing
                        factory made cementitious products
Annex F (normative) - Additional procedures for testing
                      factory made cementitious products
                      at elevated temperature
         F.1 General
         F.2 Test procedure at elevated temperature
             F.2.1 General
             F.2.2 Preparation of migration water for the
                   assessment of migration of substances
         F.3 Control samples (blank test)
         F.4 Expression of results
         F.5 Reporting
Annex G (informative) - Discrimination between porous
                        and non-porous coatings on factory
                        made products
         G.1 Principle
         G.2 Apparatus
             G.2.1 stainless steel plates
             G.2.2 cylinders
             G.2.3 pH meter
         G.3 Materials and reagents
             G.3.1 sealing compound/sealant
             G.3.2 demineralized water
         G.4 Test procedure
             G.4.1 General
             G.4.2 Laboratory blank
             G.4.3 Coated product
         G.5 Determination of pH
         G.6 Expression of results
         G.7 Classification criteria
Annex H (informative) - Schematic description of the
                        test procedure
         H.1 Preconditioning
         H.2 Production of migration water at 23 degree C
         H.3 Typical Schedule
             H.3.1 Preconditioning
             H.3.2 Production of migration waters
Annex I (informative) - Procedural tests using standard
                        additions (positive controls)
Bibliography

Describes a method to determine the migration of substances from factory made cementitious products into test waters after contact with the products.