I.S. EN 1501-1:2011
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
REFUSE COLLECTION VEHICLES - GENERAL REQUIREMENTS AND SAFETY REQUIREMENTS - PART 1: REAR LOADED REFUSE COLLECTION VEHICLES
Hardcopy , PDF
29-04-2021
English
29-08-2011
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 List of significant hazards
5 Safety requirements and/or protective measures
6 Verification of safety measures and/or protective
measures
7 Information for use
Annex A (normative) - Description of interfaces,
volumes, and systems
Annex B (normative) - Open and closed systems -
Footboard(s)
Annex C (informative) - Technical file
Annex ZA (informative) - Relationship between this
Standard and the Essential Requirements of
EU Directive 2006/42EC
Bibliography
Covers all significant hazards, hazardous situations and events relevant to the rear loaded RCV, when it is used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer, throughout its foreseeable lifetime.
| DevelopmentNote |
2011 Edition Re-Issued in April 2015 & incorporates AMD 1 2015. (04/2015)
|
| DocumentType |
Standard
|
| Pages |
64
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| ONORM EN 1501-1 : 2015 | Identical |
| NF EN 1501-1 : 2011 + A1 2015 | Identical |
| BS EN 1501-1 : 2011 | Identical |
| NEN EN 1501-1 : 2011 + A1 2015 | Identical |
| DIN EN 1501-1:2016-03 | Identical |
| NS EN 1501-1 : 2011 + A1 2015 | Identical |
| NBN EN 1501-1 : 2011 + A1 2015 | Identical |
| UNI EN 1501-1 : 2011 | Identical |
| SN EN 1501-1 : 2011 + A1 2015 | Identical |
| EN 1501-1:2011+A1:2015 | Identical |
| UNE-EN 1501-1:2012 | Identical |
| EN 12096:1997 | Mechanical vibration - Declaration and verification of vibration emission values |
| ISO 13855:2010 | Safety of machinery — Positioning of safeguards with respect to the approach speeds of parts of the human body |
| CEN Guide 414:2017 | Safety of machinery - Rules for the drafting and presentation of safety standards |
| EN 1501-2:2005+A1:2009 | Refuse collection vehicles and associated lifting devices - General requirements and safety requirements - Part 2: Side loaded refuse collection vehicles |
| EN 500-1:2006+A1:2009 | Mobile road construction machinery - Safety - Part 1: Common requirements |
| EN 894-3:2000+A1:2008 | Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 3: Control actuators |
| EN 1037:1995+A1:2008 | Safety of machinery - Prevention of unexpected start-up |
| EN 547-2:1996+A1:2008 | Safety of machinery - Human body measurements - Part 2: Principles for determining the dimensions required for access openings |
| EN 1088:1995+A2:2008 | Safety of machinery - Interlocking devices associated with guards - Principles for design and selection |
| EN 1501-5:2011 | Refuse collection vehicles - General requirements and safety requirements - Part 5: Lifting devices for refuse collection vehicles |
| EN 894-2:1997+A1:2008 | Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 2: Displays |
| ISO 15817:2012 | Earth-moving machinery — Safety requirements for remote operator control systems |
| EN 1501-4:2007 | Refuse collection vehicles and their associated lifting devices - General requirements and safety requirements - Part 4: Noise test code for refuse collection vehicles |
| ISO 3411:2007 | Earth-moving machinery Physical dimensions of operators and minimum operator space envelope |
| EN ISO 3411:2007 | Earth-moving machinery - Physical dimensions of operators and minimum operator space envelope (ISO 3411:2007) |
| ISO 4413:2010 | Hydraulic fluid power General rules and safety requirements for systems and their components |
| EN 349:1993+A1:2008 | Safety of machinery - Minimum gaps to avoid crushing of parts of the human body |
| IEC 60204-1:2016 | Safety of machinery - Electrical equipment of machines - Part 1: General requirements |
| EN 547-1:1996+A1:2008 | Safety of machinery - Human body measurements - Part 1: Principles for determining the dimensions required for openings for whole body access into machinery |
| EN ISO 13850:2015 | Safety of machinery - Emergency stop function - Principles for design (ISO 13850:2015) |
| EN 1501-3:2008 | Refuse collection vehicles and their associated lifting devices - General requirements and safety requirements - Part 3: Front loaded refuse collection vehicles |
| EN ISO 7731:2008 | Ergonomics - Danger signals for public and work areas - Auditory danger signals (ISO 7731:2003) |
| EN ISO 13857:2008 | Safety of machinery - Safety distances to prevent hazard zones being reached by upper and lower limbs (ISO 13857:2008) |
| ISO 12100:2010 | Safety of machinery — General principles for design — Risk assessment and risk reduction |
| ISO 7731:2003 | Ergonomics Danger signals for public and work areas Auditory danger signals |
| EN 574:1996+A1:2008 | Safety of machinery - Two-hand control devices - Functional aspects - Principles for design |
| EN ISO 13855:2010 | Safety of machinery - Positioning of safeguards with respect to the approach speeds of parts of the human body (ISO 13855:2010) |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| EN 953:1997+A1:2009 | Safety of machinery - Guards - General requirements for the design and construction of fixed and movable guards |
| EN 13309:2010 | Construction machinery - Electromagnetic compatibility of machines with internal power supply |
| EN ISO 4414:2010 | Pneumatic fluid power - General rules and safety requirements for systems and their components (ISO 4414:2010) |
| ISO 13849-2:2012 | Safety of machinery — Safety-related parts of control systems — Part 2: Validation |
| ISO 13857:2008 | Safety of machinery Safety distances to prevent hazard zones being reached by upper and lower limbs |
| EN ISO 12100:2010 | Safety of machinery - General principles for design - Risk assessment and risk reduction (ISO 12100:2010) |
| EN ISO 13849-2:2012 | Safety of machinery - Safety-related parts of control systems - Part 2: Validation (ISO 13849-2:2012) |
| EN ISO 6743-4:2015 | Lubricants, industrial oils and related products (class L) - Classification - Part 4: Family H (Hydraulic systems) (ISO 6743-4:2015) |
| EN ISO 13849-1:2015 | Safety of machinery - Safety-related parts of control systems - Part 1: General principles for design (ISO 13849-1:2015) |
| ISO 4414:2010 | Pneumatic fluid power General rules and safety requirements for systems and their components |
| ISO 13850:2015 | Safety of machinery Emergency stop function Principles for design |
| IEC 61310-1:2007 | Safety of machinery - Indication, marking and actuation - Part 1: Requirements for visual, acoustic and tactile signals |
| EN 60529:1991/AC:2016-12 | DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015) |
| ISO 7000:2014 | Graphical symbols for use on equipment Registered symbols |
| EN ISO 4413:2010 | Hydraulic fluid power - General rules and safety requirements for systems and their components (ISO 4413:2010) |
| ISO 13849-1:2015 | Safety of machinery — Safety-related parts of control systems — Part 1: General principles for design |
| EN 61310-1:2008 | Safety of machinery - Indication, marking and actuation - Part 1: Requirements for visual, acoustic and tactile signals |
| ISO 6743-4:2015 | Lubricants, industrial oils and related products (class L) Classification Part 4: Family H (Hydraulic systems) |
| EN 60204-1 : 2006 COR 2010 | SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 1: GENERAL REQUIREMENTS |
| EN 894-1:1997+A1:2008 | Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 1: General principles for human interactions with displays and control actuators |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.