I.S. EN 15714-3:2009
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
INDUSTRIAL VALVES - ACTUATORS - PART 3: PNEUMATIC PART-TURN ACTUATORS FOR INDUSTRIAL VALVES - BASIC REQUIREMENTS
Hardcopy , PDF
29-05-2023
English
01-01-2009
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Foreword
1 Scope
2 Normative references
3 Classification/Designation
4 Design requirements
5 Conformity assessment
6 Marking
7 Part-turn actuator selection guidelines
8 Documentation
Annex A (normative) Endurance test procedure
Annex B (informative) Actuator selection guidelines
Bibliography
Gives basic requirements for pneumatic part-turn valve actuators, both double acting and single acting, used for on-off and modulating control duties.
| DocumentType |
Standard
|
| Pages |
25
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| EN 15714-3:2009 | Identical |
| EN 15714-1:2009 | Industrial valves - Actuators - Part 1: Terminology and definitions |
| EN ISO 4628-1:2016 | Paints and varnishes - Evaluation of degradation of coatings - Designation of quantity and size of defects, and of intensity of uniform changes in appearance - Part 1: General introduction and designation system (ISO 4628-1:2016) |
| EN ISO 3231:1997 | Paints and varnishes - Determination of resistance to humid atmospheres containing sulfur dioxide (ISO 3231:1993) |
| ISO 12944-5:2007 | Paints and varnishes Corrosion protection of steel structures by protective paint systems Part 5: Protective paint systems |
| EN 60534-6-2:2001 | Industrial-process control valves - Part 6-2: Mounting details for attachment of positioners to control valves - Positioner mounting on rotary actuators |
| ISO 8573-2:2007 | Compressed air Part 2: Test methods for oil aerosol content |
| EN ISO 9227:2017 | Corrosion tests in artificial atmospheres - Salt spray tests (ISO 9227:2017) |
| EN 736-2:2016 | Valves - Terminology - Part 2: Definition of components of valves |
| EN ISO 228-1:2003 | Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions, tolerances and designation (ISO 228-1:2000) |
| ISO 8573-1:2010 | Compressed air Part 1: Contaminants and purity classes |
| ISO 8573-3:1999 | Compressed air Part 3: Test methods for measurement of humidity |
| ASME B1.20.1 : 2013(R2018) | PIPE THREADS, GENERAL PURPOSE (INCH) |
| ISO 12944-2:2017 | Paints and varnishes — Corrosion protection of steel structures by protective paint systems — Part 2: Classification of environments |
| ISO 4628-1:2016 | Paints and varnishes Evaluation of degradation of coatings Designation of quantity and size of defects, and of intensity of uniform changes in appearance Part 1: General introduction and designation system |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| ISO 5599-1:2001 | Pneumatic fluid power — Five-port directional control valves — Part 1: Mounting interface surfaces without electrical connector |
| EN 12570:2000 | Industrial valves - Method for sizing the operating element |
| ISO 9227:2017 | Corrosion tests in artificial atmospheres — Salt spray tests |
| IEC 60534-6-2:2000 | Industrial-process control valves - Part 6-2: Mounting details for attachment of positioners to control valves - Positioner mounting on rotary actuators |
| EN 60529:1991/AC:2016-12 | DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015) |
| ISO 5599-2:2001 | Pneumatic fluid power — Five-port directional control valves — Part 2: Mounting interface surfaces with optional electrical connector |
| ISO 8573-4:2001 | Compressed air Part 4: Test methods for solid particle content |
| EN ISO 5211:2017 | Industrial valves - Part-turn actuator attachments (ISO 5211:2017) |
| ISO 228-1:2000 | Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation |
| EN 736-3:2008 | Valves - Terminology - Part 3: Definition of terms |
| ISO 5211:2017 | Industrial valves — Part-turn actuator attachments |
| ISO 3231:1993 | Paints and varnishes — Determination of resistance to humid atmospheres containing sulfur dioxide |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.