I.S. EN 16145:2012
Current
The latest, up-to-date edition.
SANITARY TAPWARE - EXTRACTABLE OUTLETS FOR SINK AND BASIN MIXERS - GENERAL TECHNICAL SPECIFICATION
Hardcopy , PDF
English
01-01-2012
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Classification
5 Designation
6 Marking
7 Materials
8 Dimensional Characteristics
9 Leaktightness Characteristics
10 Mechanical Characteristics
11 Hydraulic Characteristics
12 Backflow protection
13 Acoustic characteristics
14 Rotary connection
Annex A (informative) - Pressure take-off tee
Bibliography
Defines: - the dimensional, leaktightness, mechanical, hydraulic and acoustic characteristics with which extractable outlets with or without spray mode selector function need to comply; - the procedures for testing these characteristics.
| DocumentType |
Standard
|
| Pages |
31
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Current
|
| Standards | Relationship |
| EN 16145:2012 | Equivalent |
| BS EN 16145:2012 | Equivalent |
| ISO 3822-1:1999 | Acoustics — Laboratory tests on noise emission from appliances and equipment used in water supply installations — Part 1: Method of measurement |
| EN 817:2008 | Sanitary tapware - Mechanical mixing valves (PN 10) - General technical specifications |
| EN 1287:2017 | Sanitary tapware - Low pressure thermostatic mixing valves - General technical specification |
| EN 16146:2012+A1:2014 | Sanitary tapware - Extractable shower hoses for sanitary tapware for supply systems type 1 and type 2 - General technical specification |
| EN 1254-2:1998 | Copper and copper alloys - Plumbing fittings - Part 2: Fittings with compression ends for use with copper tubes |
| ISO 3822-4:1997 | Acoustics — Laboratory tests on noise emission from appliances and equipment used in water supply installations — Part 4: Mounting and operating conditions for special appliances |
| EN 1286:1999 | Sanitary tapware - Low pressure mechanical mixing valves - General technical specification |
| EN 1717:2000 | Protection against pollution of potable water in water installations and general requirements of devices to prevent pollution by backflow |
| EN ISO 228-1:2003 | Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions, tolerances and designation (ISO 228-1:2000) |
| EN ISO 3822-4:1997 | Acoustics - Laboratory tests on noise emission from appliances and equipment used in water supply installations - Part 4: Mounting and operating conditions for special appliances |
| EN ISO 5167-1:2003 | Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 1: General principles and requirements (ISO 5167-1:2003) |
| ISO 5167-1:2003 | Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full — Part 1: General principles and requirements |
| EN 200:2008 | Sanitary tapware - Single taps and combination taps for water supply systems of type 1 and type 2 - General technical specification |
| EN 1111:2017 | Sanitary tapware - Thermostatic mixing valves (PN 10) - General technical specification |
| ISO 228-1:2000 | Pipe threads where pressure-tight joints are not made on the threads — Part 1: Dimensions, tolerances and designation |
| EN 248:2002 | Sanitary tapware - General specification for electrodeposited coatings of Ni-Cr |
Access your standards online with a subscription
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Important note : Users cannot be edited or removed once added to your Multi user PDF.