• I.S. EN 16767:2016

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

    INDUSTRIAL VALVES - STEEL AND CAST IRON CHECK VALVES

    Available format(s):  Hardcopy, PDF

    Superseded date:  13-05-2020

    Language(s):  English

    Published date:  01-01-2016

    Publisher:  National Standards Authority of Ireland

    For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
    Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

    Dates of withdrawal of national standards are available from NSAI.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    National Foreword
    European foreword
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Requirements
    5 Test procedures
    6 Declaration of compliance
    7 Designation
    8 Marking, preparation for storage and transportation
    Annex A (informative) - Information to be supplied
             by the purchaser
    Annex ZA (informative) - Relationship between this European
             Standard and the essential requirements of
             Directive 2014/68/EU (Pressure equipment
             Directive) aimed to be covered
    Bibliography

    Abstract - (Show below) - (Hide below)

    Defines the requirements for cast iron or steel check valves, which are forged, cast or fabricated in straight, angle or oblique pattern with end connections flanged or wafer, butt welding, socket welding, or threaded.

    General Product Information - (Show below) - (Hide below)

    Development Note Supersedes I.S. EN 12334 & I.S. EN 14341. (05/2016)
    Document Type Standard
    Publisher National Standards Authority of Ireland
    Status Superseded
    Superseded By
    Supersedes

    Standards Referencing This Book - (Show below) - (Hide below)

    EN 12982:2009 Industrial valves - End-to-end and centre-to-end dimensions for butt welding end valves
    EN ISO 9692-1:2013 Welding and allied processes - Types of joint preparation - Part 1: Manual metal arc welding, gas-shielded metal arc welding, gas welding, TIG welding and beam welding of steels (ISO 9692-1:2013)
    EN 10269:2013 Steels and nickel alloys for fasteners with specified elevated and/or low temperature properties
    ISO 7005-2:1988 Metallic flanges — Part 2: Cast iron flanges
    EN 16722:2015 Industrial valves - End-to-end and centre-to-end dimensions for valves with threaded ends
    PREN 558 : DRAFT 2015 INDUSTRIAL VALVES - FACE-TO-FACE AND CENTRE-TO-FACE DIMENSIONS OF METAL VALVES FOR USE IN FLANGED PIPE SYSTEMS - PN AND CLASS DESIGNATED VALVES
    EN ISO 1043-1:2011/A1:2016 PLASTICS - SYMBOLS AND ABBREVIATED TERMS - PART 1: BASIC POLYMER AND THEIR SPECIAL CHARACTERISTICS (ISO 1043-1:2011/AMD 1:2016)
    EN 1759-1:2004 Flanges and their joint - Circular flanges for pipes, valves, fittings and accessories, Class designated - Part 1: Steel flanges, NPS 1/2 to 24
    ISO 14732:2013 Welding personnel Qualification testing of welding operators and weld setters for mechanized and automatic welding of metallic materials
    EN 12266-2:2012 Industrial valves - Testing of metallic valves - Part 2: Tests, test procedures and acceptance criteria - Supplementary requirements
    ISO 9606-1:2012 Qualification testing of welders — Fusion welding — Part 1: Steels
    EN 12516-1:2014 Industrial valves - Shell design strength - Part 1: Tabulation method for steel valve shells
    EN 12516-4:2014 Industrial valves - Shell design strength - Part 4: Calculation method for valve shells manufactured in metallic materials other than steel
    EN ISO 14732:2013 Welding personnel - Qualification testing of welding operators and weld setters for mechanized and automatic welding of metallic materials (ISO 14732:2013)
    EN 736-2:2016 Valves - Terminology - Part 2: Definition of components of valves
    ISO 148-1:2016 Metallic materials — Charpy pendulum impact test — Part 1: Test method
    EN ISO 228-1:2003 Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions, tolerances and designation (ISO 228-1:2000)
    EN 12266-1:2012 Industrial valves - Testing of metallic valves - Part 1: Pressure tests, test procedures and acceptance criteria - Mandatory requirements
    ISO 9692-1:2013 Welding and allied processes — Types of joint preparation — Part 1: Manual metal arc welding, gas-shielded metal arc welding, gas welding, TIG welding and beam welding of steels
    ISO 7-1:1994 Pipe threads where pressure-tight joints are made on the threads Part 1: Dimensions, tolerances and designation
    EN 12351:2010 Industrial valves - Protective caps for valves with flanged connections
    EN 12516-3:2002/AC:2003 VALVES - SHELL DESIGN STRENGTH - PART 3: EXPERIMENTAL METHOD
    ISO 4200:1991 Plain end steel tubes, welded and seamless — General tables of dimensions and masses per unit length
    EN 1515-4:2009 Flanges and their joints - Bolting - Part 4: Selection of bolting for equipment subject to the Pressure Equipment Directive 97/23/EC
    EN 12760:2016 Industrial valves - Socket welding ends for steel valves
    EN ISO 148-1:2016 Metallic materials - Charpy pendulum impact test - Part 1: Test method (ISO 148-1:2016)
    EN 12516-2:2014 Industrial valves - Shell design strength - Part 2: Calculation method for steel valve shells
    ISO 15607:2003 Specification and qualification of welding procedures for metallic materials General rules
    EN ISO 9606-1:2017 Qualification testing of welders - Fusion welding - Part 1: Steels (ISO 9606-1:2012 including Cor 1:2012 and Cor 2:2013)
    EN 1092-2:1997 Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, PN designated - Part 2: Cast iron flanges
    EN 19:2016 Industrial valves - Marking of metallic valves
    ISO 1043-1:2011 Plastics — Symbols and abbreviated terms — Part 1: Basic polymers and their special characteristics
    ISO 228-1:2000 Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation
    ISO 1629:2013 Rubber and latices — Nomenclature
    EN ISO 15607:2003 Specification and qualification of welding procedures for metallic materials - General rules (ISO 15607:2003)
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective