I.S. EN 1915-2:2001
Withdrawn
A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.
AIRCRAFT GROUND SUPPORT EQUIPMENT - GENERAL REQUIREMENTS - PART 2: STABILITY AND STRENGTH REQUIREMENTS, CALCULATIONS AND TEST METHODS
Hardcopy , PDF
26-05-2009
English
24-08-2001
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 List of hazards
5 Safety requirements and/or protective measures
5.1 General
5.2 Requirements for the strength calculation
of steel constructions
5.2.1 General remarks
5.2.2 Loads and load combinations
5.2.3 Materials
5.2.4 Factors for stress calculations
5.2.5 Combined stresses
5.2.6 Fatigue
5.3 Requirements for the calculation of safety
related machinery parts
5.3.1 Chain lifting elements
5.3.2 Cylinders, pipes and hoses used
in lifting systems
5.3.3 Wire rope lifting elements
5.3.4 Winches
5.3.5 Winching plants
5.3.6 Stabilizers
5.4 Stability calculations
5.4.1 Loads and forces
5.4.2 Ground slope
5.4.3 Elastic deflection
5.4.4 Flat tyres
5.4.5 Load combinations
5.4.6 Stability criteria
6 Information for use
7 Verification of safety requirements and/or measures
7.1 General
7.2 Verification of strength
7.2.1 Test loads
7.2.2 Test procedure
7.2.3 Test results
7.3 Verification of stability
7.3.1 General
7.3.2 Test loads
7.3.3 Test procedure
7.3.4 Test results
Annex A (informative) - Examples for load geometry
Annex B (normative) - Wind shape factors
Annex ZA (informative) - Relationship between this European
Standard and the Essential Requirements of EU
Directive 98/37/EC
Annex ZB (informative) - Relationship between this European
Standard and the Essential Requirements of EU
Directive 2006/42/EC
Bibliography
Describes the conditions to be taken into consideration when calculating the strength and the stability of GSE according to EN 1915-1 and the EN 12312 series under intended use conditions.
DevelopmentNote |
2001 Edition Re-Issued in May 2009 & incorporates AMD 1 2009. (06/2009)
|
DocumentType |
Standard
|
Pages |
32
|
PublisherName |
National Standards Authority of Ireland
|
Status |
Withdrawn
|
Standards | Relationship |
SN EN 1915-2 : 2001 + A1 2009 | Identical |
UNE-EN 1915-2:2001 | Identical |
UNI EN 1915-2 : 2001 | Identical |
NBN EN 1915-2 : 2001 + A1 2009 | Identical |
NS EN 1915-2 : 2001 + A1 2009 | Identical |
BS EN 1915-2 : 2001 | Identical |
EN 1915-2:2001+A1:2009 | Identical |
NF EN 1915-2 : 2002 + A1 2010 | Identical |
NEN EN 1915-2 : 2001 + A1 2009 | Identical |
ISO 3834-1:2005 | Quality requirements for fusion welding of metallic materials Part 1: Criteria for the selection of the appropriate level of quality requirements |
ISO 2408:2017 | Steel wire ropes — Requirements |
EN ISO 3834-3:2005 | Quality requirements for fusion welding of metallic materials - Part 3: Standard quality requirements (ISO 3834-3:2005) |
EN ISO 5817:2014 | Welding - Fusion-welded joints in steel, nickel, titanium and their alloys (beam welding excluded) - Quality levels for imperfections (ISO 5817:2014) |
EN 982:1996+A1:2008 | Safety of machinery - Safety requirements for fluid power systems and their components - Hydraulics |
EN 1915-3:2004+A1:2009 | Aircraft ground support equipment - General requirements - Part 3: Vibration measurement methods and reduction |
EN ISO 3834-2:2005 | Quality requirements for fusion welding of metallic materials - Part 2: Comprehensive quality requirements (ISO 3834-2:2005) |
SAE ARP 1330 : 2014 | WELDING OF STRUCTURES FOR GROUND SUPPORT EQUIPMENT |
ISO 3834-4:2005 | Quality requirements for fusion welding of metallic materials Part 4: Elementary quality requirements |
EN ISO 3834-4:2005 | Quality requirements for fusion welding of metallic materials - Part 4: Elementary quality requirements (ISO 3834-4:2005) |
EN 1915-4:2004+A1:2009 | Aircraft ground support equipment - General requirements - Part 4: Noise measurement methods and reduction |
SAE ARP 1328 : 2012 | AIRCRAFT GROUND SUPPORT EQUIPMENT - WIND STABILITY DETERMINATION |
ISO 8625-1:1993 | Aerospace Fluid systems Vocabulary Part 1: General terms and definitions related to pressure |
ISO 5817:2014 | Welding — Fusion-welded joints in steel, nickel, titanium and their alloys (beam welding excluded) — Quality levels for imperfections |
ISO 3834-2:2005 | Quality requirements for fusion welding of metallic materials Part 2: Comprehensive quality requirements |
ISO 12100-2:2003 | Safety of machinery Basic concepts, general principles for design Part 2: Technical principles |
EN ISO 3834-1:2005 | Quality requirements for fusion welding of metallic materials - Part 1: Criteria for the selection of the appropriate level of quality requirements (ISO 3834-1:2005) |
ISO 12100-1:2003 | Safety of machinery Basic concepts, general principles for design Part 1: Basic terminology, methodology |
EN 1915-1:2013 | Aircraft ground support equipment - General requirements - Part 1: Basic safety requirements |
ISO 11995:1996 | Aircraft — Stability requirements for loading and servicing equipment |
ISO 3834-3:2005 | Quality requirements for fusion welding of metallic materials Part 3: Standard quality requirements |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.