I.S. EN 200:2008
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
SANITARY TAPWARE - SINGLE TAPS AND COMBINATION TAPS FOR WATER SUPPLY SYSTEMS OF TYPE 1 AND TYPE 2 - GENERAL TECHNICAL SPECIFICATION
Hardcopy , PDF
11-01-2024
English
01-01-2008
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Foreword
Introduction
1 Scope
2 Normative references
3 Designation
4 Marking and identification
5 Materials
6 Dimensional characteristics
7 Sequence of testing
8 Leaktightness characteristics
9 Pressure resistance characteristics - mechanical performance
under pressure
10 Hydraulic characteristics
11 Mechanical strength characteristics - torsion test for
operating mechanism
12 Mechanical endurance characteristics
13 Backflow protection
14 Acoustic characteristics
Annex A (informative) Pressure take-off tee
Bibliography
Pertains to draw-off taps (single taps and combination taps) for use with sanitary appliances installed in rooms used for bodily hygiene (cloakrooms, bathrooms etc.) and in kitchens, i.e. for use with baths, wash basins, bidets, showers and sinks.
| DevelopmentNote |
Supersedes I.S. 287. (05/2017)
|
| DocumentType |
Standard
|
| Pages |
53
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| NBN EN 200 : 2008 | Identical |
| UNE-EN 200:2008 | Identical |
| SN EN 200 : 2008 | Identical |
| NF EN 200 : 2008 | Identical |
| UNI EN 200 : 2008 | Identical |
| BS EN 200:2008 | Identical |
| EN 200:2008 | Identical |
| NEN EN 200 : 2008 | Identical |
| NS EN 200 : 3ED 2008 | Identical |
| ONORM EN 200 : 2008 | Identical |
| DIN EN 200:2008-10 | Identical |
| ISO 3822-1:1999 | Acoustics Laboratory tests on noise emission from appliances and equipment used in water supply installations Part 1: Method of measurement |
| EN 246:2003 | Sanitary tapware - General specifications for flow rate regulators |
| EN 1112:2008 | Sanitary tapware - Shower outlets for sanitary tapware for water supply systems of type 1 and type 2 - General technical specification |
| EN 1254-2:1998 | Copper and copper alloys - Plumbing fittings - Part 2: Fittings with compression ends for use with copper tubes |
| EN 1113:2015 | Sanitary tapware - Shower hoses for sanitary tapware for water supply systems of type 1 and type 2 - General technical specification |
| ISO 3822-4:1997 | Acoustics Laboratory tests on noise emission from appliances and equipment used in water supply installations Part 4: Mounting and operating conditions for special appliances |
| EN 1717:2000 | Protection against pollution of potable water in water installations and general requirements of devices to prevent pollution by backflow |
| EN ISO 228-1:2003 | Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions, tolerances and designation (ISO 228-1:2000) |
| EN ISO 3822-4:1997 | Acoustics - Laboratory tests on noise emission from appliances and equipment used in water supply installations - Part 4: Mounting and operating conditions for special appliances |
| EN 14506:2005 | Devices to prevent pollution by backflow of potable water - Automatic diverter - Family H, type C |
| EN ISO 5167-1:2003 | Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 1: General principles and requirements (ISO 5167-1:2003) |
| ISO 3822-2:1995 | Acoustics Laboratory tests on noise emission from appliances and equipment used in water supply installations Part 2: Mounting and operating conditions for draw-off taps and mixing valves |
| ISO 5167-1:2003 | Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full Part 1: General principles and requirements |
| EN ISO 3822-2:1995 | Acoustics - Laboratory tests on noise emission from appliances and equipment used in water supply installations - Part 2: Mounting and operating conditions for draw-off taps and mixing valves (ISO 3822-2:1995) |
| ISO 228-1:2000 | Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation |
| EN 248:2002 | Sanitary tapware - General specification for electrodeposited coatings of Ni-Cr |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.