I.S. EN 60317-25:2010
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 25: POLYESTER OR POLYESTERIMIDE OVERCOATED WITH POLYAMIDE-IMIDE ENAMELLED ROUND ALUMINIUM WIRE, CLASS 200
Hardcopy , PDF
01-09-2020
English
01-01-2010
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms, definitions and general notes on methods
of test and appearance
4 Dimensions
5 Electrical resistance
6 Elongation
7 Springiness
8 Flexibility and adherence
9 Heat shock
10 Cut-through
11 Resistance to abrasion (nominal conductor diameters up
to and including 2,500 mm)
12 Resistance to solvents
13 Breakdown voltage
14 Continuity of insulation
15 Temperature index
16 Resistance to refrigerants
17 Solderability
18 Heat or solvent bonding
19 Dielectric dissipation factor
20 Resistance to transformer oil
21 Loss of mass
23 Pin hole test
30 Packaging
Annex ZA (normative) - Normative references to international
publications with their corresponding European
publications
Describes the requirements of enamelled round aluminium winding wires of class 200 with a dual coating.
| DevelopmentNote |
For CENELEC adoptions of IEC publications, please check www.iec.ch to be sure that you have any corrigenda that may apply. (01/2017)
|
| DocumentType |
Standard
|
| Pages |
15
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| NBN EN 60317-25 : 2010 | Identical |
| IEC 60317-25:2010 | Identical |
| BS EN 60317-25:2010 | Identical |
| DIN EN 60317-25:2011-02 | Identical |
| SN EN 60317-25 : 1996 AMD 2 1998 | Identical |
| NF EN 60317-25 : 2012 | Identical |
| EN 60317-25:2010 | Identical |
| UNE-EN 60317-25:2010 | Identical |
| IEC 60317-0-3:2008+AMD1:2013 CSV | Specifications for particular types of winding wires - Part 0-3:General requirements - Enamelled round aluminium wire |
| IEC 60851-5:2008+AMD1:2011 CSV | Winding wires - Test methods - Part 5: Electrical properties |
| EN 60317-0-3:2008/A1:2013 | SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 0-3: GENERAL REQUIREMENTS - ENAMELLED ROUND ALUMINIUM WIRE (IEC 60317-0-3:2008/A1:2013) |
| EN 60851-4:2016 | Winding wires - Test methods - Part 4: Chemical properties |
| EN 60851-5:2008/A1:2011 | WINDING WIRES - TEST METHODS - PART 5: ELECTRICAL PROPERTIES (IEC 60851-5:2008) |
| IEC 60851-4:2016 | Winding wires - Test methods - Part 4: Chemical properties |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.