I.S. EN 61076-1:2006/A1:2019
Current
The latest, up-to-date edition.
CONNECTORS FOR ELECTRONIC EQUIPMENT - PRODUCT REQUIREMENTS - PART 1: GENERIC SPECIFICATION
Hardcopy , PDF
English
01-01-2006
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
FOREWORD
INTRODUCTION
1 General
1.1 Scope
1.2 General considerations relating to specifications
1.3 Normative references
1.4 Performance characteristics
2 Technical information
2.1 Terms and definitions
2.2 System of levels
2.3 Classification into climatic categories
2.4 Clearance and creepage distances
2.5 Current-carrying capacity
2.6 IEC type designation
2.7 Marking
3 Dimensional information
3.1 Drawings and dimensions
3.2 System of lettering
3.3 Purpose
3.4 Detailed information
3.5 Gauges
4 Quality assessment procedures
5 Tests and test schedules
5.1 General aspects
5.2 Test schedules
5.3 Test procedures and measuring methods
5.4 Preconditioning
5.5 Wiring and mounting of specimens
Annex A (normative) Common lettering system to be used
in drawings
Annex ZA (normative) Normative references to international
publications with there corresponding European
publications
Gives uniform specifications and technical information for connectors. Applicable to a family of connectors for use in electronic and electrical equipment; connectors designed for use at radio frequencies are not covered.
| Committee |
TC 48
|
| DevelopmentNote |
For CENELEC adoptions of IEC publications, please check www.iec.ch to be sure that you have any corrigenda that may apply. (01/2017)
|
| DocumentType |
Standard
|
| Pages |
78
|
| ProductNote |
CSV VERSION IS NOW AVAILABLE FOR THIS STANDARD The date of any NSAI previous adoption may not match the date of its original CEN/CENELEC document.
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Current
|
| Supersedes |
| Standards | Relationship |
| NF EN 61076-1 : 2006 | Identical |
| NBN EN 61076-1 : 2006 | Identical |
| EN 61076-1:2006 | Identical |
| SN EN 61076-1 : 2006 | Identical |
| UNE EN 61076-1 : 1997 A2 2002 | Identical |
| IEC 61076-1:2006 | Identical |
| BS EN 61076-1:2006 | Identical |
| DIN EN 61076-1:2007-02 | Identical |
| UNE EN 61076-1 : 1997 A2 2002 | Identical |
| IEC GUIDE 109:2012 | Environmental aspects - Inclusion in electrotechnical product standards |
| EN 20286-2 : 1993 | ISO SYSTEM OF LIMITS AND FITS - TABLES OF STANDARD TOLERANCE GRADES AND LIMIT DEVIATIONS FOR HOLES AND SHAFTS |
| IEC 61076-3:2008 | Connectors for electronic equipment - Product requirements - Part 3: Rectangular connectors - Sectional specification |
| IEC 60068-1:2013 | Environmental testing - Part 1: General and guidance |
| IEC TR 62225:2001 | Guidance on terms for connectors and mechanical structures in electronic equipment |
| EN ISO 1101:2017 | Geometrical product specifications (GPS) - Geometrical tolerancing - Tolerances of form, orientation, location and run-out (ISO 1101:2017) |
| ISO 1101:2017 | Geometrical product specifications (GPS) — Geometrical tolerancing — Tolerances of form, orientation, location and run-out |
| EN 60068-1:2014 | Environmental testing - Part 1: General and guidance |
| IEC 61076-6:2004 | Connectors for electronic equipment - Part 6: Loose part contacts - Sectional specification |
| IEC 61076-7:2000 | Connectors for use in d.c., low-frequency analogue and digital high speed data applications - Part 7: Cable outlet accessories with assessed quality, including qualification and capability approval - Sectional specifiation |
| EN 20286-1 : 1993 | ISO SYSTEM OF LIMITS AND FITS - BASES OF TOLERANCES, DEVIATIONS AND FITS |
| ISO 1302:2002 | Geometrical Product Specifications (GPS) Indication of surface texture in technical product documentation |
| IEC 61076-5:2001 | Connectors for use in d.c., low-frequency analogue and digital high-speed data applications - Part 5: In-line sockets with assessed quality - Sectional specification |
| IEC 61076-4:1995 | Connectors with assessed quality, for use in d.c., low-frequency analogue and in digital high-speed data applications - Part 4: Sectional specification - Printed board connectors |
| ISO 286-1:2010 | Geometrical product specifications (GPS) ISO code system for tolerances on linear sizes Part 1: Basis of tolerances, deviations and fits |
| IEC 61076-2:2011 | Connectors for electronic equipment - Product requirements - Part 2: Sectional specification for circular connectors |
| EN 60664-1:2007 | Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests |
| ISO 286-2:2010 | Geometrical product specifications (GPS) ISO code system for tolerances on linear sizes Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts |
| ISO 129-1:2004 | Technical drawings Indication of dimensions and tolerances Part 1: General principles |
| EN 62197-1 : 2006 | CONNECTORS FOR ELECTRONIC EQUIPMENT - QUALITY ASSESSMENT REQUIREMENTS - PART 1: GENERIC SPECIFICATION |
| IEC 62197-1:2006 | Connectors for electronic equipment - Quality assessment requirements - Part 1: Generic specification |
| IEC 60664-1:2007 | Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests |
| IEC 60050-581:2008 | International Electrotechnical Vocabulary (IEV) - Part 581: Electromechanical components for electronic equipment |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.