• I.S. EN 61167:2016

    Withdrawn A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.

    METAL HALIDE LAMPS - PERFORMANCE SPECIFICATION

    Available format(s):  Hardcopy, PDF

    Withdrawn date:  02-11-2021

    Language(s):  English

    Published date:  28-06-2016

    Publisher:  National Standards Authority of Ireland

    For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
    Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

    Dates of withdrawal of national standards are available from NSAI.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    National Foreword
    European foreword
    FOREWORD
    INTRODUCTION
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Lamp requirements
    5 Information for ballast, ignitor and luminaire
      design
    6 Data sheets
    Annex A (normative) - Method of measuring lamp
            starting and warm-up characteristics
    Annex B (normative) - Method of measuring electrical
            and photometrical characteristics (lamps for
            operation on 50 Hz or 60 Hz supply
            frequencies)
    Annex C (normative) - Method of test for lumen
            maintenance and life
    Annex D (informative) - Information for luminaire
            design
    Annex E (normative) - Method of measuring electrical
            and photometrical characteristics on low
            frequency square wave reference ballast
    Annex F (normative) - Spectral analysis of power
            ripple: calculation procedure for amplitude
            spectrum ratio and guidance
    Annex G (informative) - Low frequency square wave
            operation
    Annex H (informative) - Information for ballast design
    Annex I (informative) - Information regarding lamp
            performance temperature limits for
            luminaire design
    Annex J (informative) - ILCOS codes
    Bibliography
    Annex ZA (normative) - Normative references to
             international publications with their
             corresponding European publications
    Annex ZZA (informative) - Relationship between this
              European Standard and the requirements of
              Commission Regulation (EC) No 245/2009
    Annex ZZB (informative) - Relationship between this
              European Standard and the requirements of
              Commission Regulation (EU) No 1194/2012
    Annex ZZC (informative) - Relationship between this
              European Standard and the requirements of
              Commission Regulation (EU) No 874/2012

    Abstract - (Show below) - (Hide below)

    Defines the performance requirements for metal halide lamps for general lighting purposes.

    General Product Information - (Show below) - (Hide below)

    Committee TC 34
    Development Note For CENELEC adoptions of IEC publications, please check www.iec.ch to be sure that you have any corrigenda that may apply. (01/2017)
    Document Type Standard
    Product Note The date of any NSAI previous adoption may not match the date of its original CEN/CENELEC document.
    Publisher National Standards Authority of Ireland
    Status Withdrawn
    Superseded By
    Supersedes

    Standards Referencing This Book - (Show below) - (Hide below)

    IEC 60682:1980 Standard method of measuring the pinch temperature of quartz-tungsten-halogen lamps
    IEC TR 61341:2010 Method of measurement of centre beam intensity and beam angle(s) of reflector lamps
    IEC 60188:2001 High-pressure mercury vapour lamps - Performance specifications
    IEC 60050-845:1987 International Electrotechnical Vocabulary (IEV) - Part 845: Lighting
    EN 13032-4:2015 Light and lighting - Measurement and presentation of photometric data of lamps and luminaires - Part 4: LED lamps, modules and luminaires
    EN 60923:2005/A1:2006 AUXILIARIES FOR LAMPS - BALLASTS FOR DISCHARGE LAMPS (EXCLUDING TUBULAR FLUORESCENT LAMPS) - PERFORMANCE REQUIREMENTS
    EN 60927:2007/A1:2013 AUXILIARIES FOR LAMPS - STARTING DEVICES (OTHER THAN GLOW STARTERS) - PERFORMANCE REQUIREMENTS (IEC 60927:2007/A1:2013 (34C/951/CDV))
    IEC 60410:1973 Sampling plans and procedures for inspection by attributes
    EN 61341:2011 Method of measurement of centre beam intensity and beam angle(s) of reflector lamps
    IEC 62035:2014+AMD1:2016 CSV Discharge lamps (excluding fluorescent lamps) - Safety specifications
    EN 62035:2014 Discharge lamps (excluding fluorescent lamps) - Safety specifications
    IEC 61231:2010+AMD1:2013 CSV International lamp coding system (ILCOS)
    IEC 60598-1:2014+AMD1:2017 CSV Luminaires - Part 1: General requirements and tests
    IEC 60061-1:2005 CSV Lamp caps and holders together with gauges for the control of interchangeability and safety - Part 1: Lamp caps
    IEC 62471:2006 Photobiological safety of lamps and lamp systems
    IEC 60927:2007+AMD1:2013 CSV Auxiliaries for lamps - Starting devices (other than glow starters)- Performance requirements
    IEC 61126:1992 Procedure for use in the preparation of maximum lamp outlines
    EN 13032-1:2004+A1:2012 Light and lighting - Measurement and presentation of photometric data of lamps and luminaires - Part 1: Measurement and file format
    IEC 60923:2005+AMD1:2006 CSV Auxiliaries for lamps - Ballasts for discharge lamps (excluding tubular fluorescent lamps) - Performance requirements
    EN 62471:2008 Photobiological safety of lamps and lamp systems
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective