I.S. EN 61347-2-3:2011
Current
The latest, up-to-date edition.
LAMP CONTROL GEAR - PART 2-3: PARTICULAR REQUIREMENTS FOR A.C. AND/OR D.C. SUPPLIED ELECTRONIC CONTROL GEAR FOR FLUORESCENT LAMPS
Hardcopy , PDF
English
01-01-2011
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
National Foreword
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 General requirements
5 General notes on tests
6 Classification
7 Marking
8 Protection against accidental contact with live parts
9 Terminals
10 Provisions for earthing
11 Moisture resistance and insulation
12 Electric strength
13 Thermal endurance test for windings
14 Fault conditions
15 Protection of associated components
16 Abnormal conditions
17 Behaviour of the control gear at end of lamp life
18 Construction
19 Creepage distances and clearances
20 Screws, current-carrying parts and connections
21 Resistance to heat, fire and tracking
22 Resistance to corrosion
Annex A (normative) - Test to establish whether
a conductive part is a live part which
may cause an electric shock
Annex B (normative) - Particular requirements for
thermally protected lamp control gear
Annex C (normative) - Particular requirements for
electronic lamp control gear with
means of protection against overheating
Annex D (normative) - Requirements for carrying out
the heating tests of thermally protected
lamp control gear
Annex E (normative) - Use of constant S other than
4500 in t[w] tests
Annex F (normative) - Draught-proof enclosure
Annex G (normative) - Explanation of the derivation of
the values of pulse voltages
Annex H (normative) - Tests
Annex I (normative) - Measurement of high-frequency
leakage current
Annex J (normative) - Particular additional safety
requirements for a.c., a.c./d.c. or d.c.
supplied electronic control gear for emergency
lighting
Annex K (informative) - Components used in the
asymmetric pulse test circuit
Annex L (normative) - Information for control gear design
Bibliography
Annex ZA (normative) - Normative references to
international publications with their
corresponding European publications
Describes particular safety requirements for electronic control gear for use on a.c. and d.c. supplies up to 1000 V at 50 Hz or 60 Hz with operating frequencies deviating from the supply frequency, associated with fluorescent lamps as specified in IEC 60081 and IEC 60901, and other fluorescent lamps for high-frequency operation.
| DevelopmentNote |
Together with I.S. EN 61347-1 and parts 2-1, 2-2, 2-4, 2-5, 2-6, 2-7, 2-8 and 2-9 of I.S. EN 61347 supersedes I.S. EN 60920, I.S. EN 60922, I.S. EN 60924, I.S. EN 60926, I.S. EN 60928 and I.S. EN 61046. (07/2005) Supersedes I.S. EN 61347-2-4, I.S. EN 61347-2-5 & I.S. EN 61347-2-6. (11/2011) For CENELEC adoptions of IEC publications, please check www.iec.ch to be sure that you have any corrigenda that may apply.(01/2017)
|
| DocumentType |
Standard
|
| Pages |
118
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Current
|
| Supersedes |
| Standards | Relationship |
| NF EN 61347-2-3 : 2012 AMD 1 2017 | Identical |
| IEC 61347-2-3:2011+AMD1:2016 CSV | Identical |
| BS EN 61347-2-3:2011 | Identical |
| EN 61347-2-3:2011 | Equivalent |
| IEC 61347-2-3:2011 | Equivalent |
| UNE-EN 61347-2-3:2012 | Identical |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : Users cannot be edited or removed once added to your Multi user PDF.