• I.S. EN 61347-2-9:2013

    Current The latest, up-to-date edition.

    LAMP CONTROLGEAR - PART 2-9: PARTICULAR REQUIREMENTS FOR ELECTROMAGNETIC CONTROLGEAR FOR DISCHARGE LAMPS (EXCLUDING FLUORESCENT LAMPS) (IEC 61347-2-9:2012 (EQV))

    Available format(s):  Hardcopy, PDF

    Language(s):  English

    Published date:  01-01-2013

    Publisher:  National Standards Authority of Ireland

    For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
    Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

    Dates of withdrawal of national standards are available from NSAI.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    FOREWORD
    INTRODUCTION
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 General requirements
    5 General notes on tests
    6 Classification
    7 Marking
    8 Protection against accidental contact with live parts
    9 Terminals
    10 Provisions for earthing
    11 Moisture resistance and insulation
    12 Electric strength
    13 Thermal endurance test for windings
    14 Electromagnetic controlgear heating
    15 High-voltage impulse testing
    16 Fault conditions
    17 Construction
    18 Creepage distances and clearances
    19 Screws, current-carrying parts and connections
    20 Resistance to heat, fire and tracking
    21 Resistance to corrosion
    22 No-load output voltage
    Annex A (normative) - Test to establish whether a conductive
            part is a live part which may cause an electric shock
    Annex B (normative) - Particular requirements for thermally
            protected lamp electromagnetic controlgear
    Annex C (normative) - Particular requirements for electronic
            lamp controlgear with means of protection
            against overheating
    Annex D (normative) - Requirements for carrying out the
            heating tests of thermally protected lamp
            electromagnetic controlgear
    Annex E (normative) - Use of constant S other than 4500
            in tw tests
    Annex F (normative) - Draught-proof enclosure
    Annex G (normative) - Explanation of the derivation of
            the values of pulse voltages
    Annex H (normative) - Tests
    Annex I (normative) - Method for selection of varistors
    Annex J (informative) - Explanation of electromagnetic
            controlgear temperatures
    Annex K (normative) - Additional requirements for built-in
            electromagnetic controlgear with double or
            reinforced insulation
    Bibliography
    Annex ZA (normative) - Normative references to international
             publications with their corresponding European
             publications

    Abstract - (Show below) - (Hide below)

    Describes particular safety requirements for electromagnetic controlgear for discharge lamps such as high-pressure mercury vapour, low-pressure sodium vapour, high-pressure sodium vapour and metal halide lamps.

    General Product Information - (Show below) - (Hide below)

    Development Note Together with I.S. EN 61347-1 and parts 2-1, 2-2, 2-3, 2-4, 2-5, 2-6, 2-7 and 2-8 of I.S. EN 61347 supersedes I.S. EN 60920, I.S. EN 60922, I.S. EN 60924, I.S. EN 60926, I.S. EN 60928 and I.S. EN 61046. (07/2005) For CENELEC adoptions of IEC publications, please check www.iec.ch to be sure that you have any corrigenda that may apply. (01/2017)
    Document Type Standard
    Publisher National Standards Authority of Ireland
    Status Current
    Supersedes

    Standards Referencing This Book - (Show below) - (Hide below)

    EN 60188 : 2001 High-pressure mercury vapour lamps - Performance specifications
    EN 60192:2001 LOW PRESSURE SODIUM VAPOUR LAMPS - PERFORMANCE SPECIFICATIONS
    IEC 60662:2011 High-pressure sodium vapour lamps - Performance specifications
    IEC 60192:2001 Low-pressure sodium vapour lamps - Performance specifications
    IEC 60188:2001 High-pressure mercury vapour lamps - Performance specifications
    IEC 61347-1:2015 RLV Lamp controlgear - Part 1: General and safety requirements
    EN 61347-2-1:2001/A2:2014 LAMP CONTROLGEAR - PART 2-1: PARTICULAR REQUIREMENTS FOR STARTING DEVICES (OTHER THAN GLOW STARTERS) (IEC 61347-2-1:2000/A2:2013)
    IEC 61347-2-1:2000+AMD1:2005+AMD2:2013 CSV Lamp controlgear - Part 2-1: Particular requirements for startingdevices (other than glow starters)
    IEC 61167:2015 Metal halide lamps - Performance specification
    IEC 62035:2014+AMD1:2016 CSV Discharge lamps (excluding fluorescent lamps) - Safety specifications
    EN 61347-1:2015 LAMP CONTROLGEAR - PART 1: GENERAL AND SAFETY REQUIREMENTS (IEC 61347-1:2015)
    EN 62035:2014 DISCHARGE LAMPS (EXCLUDING FLUORESCENT LAMPS) - SAFETY SPECIFICATIONS (IEC 62035:2014, MODIFIED)
    IEC 60598-1:2014+AMD1:2017 CSV Luminaires - Part 1: General requirements and tests
    EN 60662:2012 HIGH-PRESSURE SODIUM VAPOUR LAMPS - PERFORMANCE SPECIFICATIONS (IEC 60662:2011, MODIFIED)
    IEC 60923:2005+AMD1:2006 CSV Auxiliaries for lamps - Ballasts for discharge lamps (excluding tubular fluorescent lamps) - Performance requirements
    IEC 61347-2-8:2000+AMD1:2006 CSV Lamp controlgear - Part 2-8: Particular requirements for ballasts for fluorescent lamps
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective