I.S. EN 62282-3-201:2017/A1:2022
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Fuel cell technologies - Part 3-201: Stationary fuel cell power systems - Performance test methods for small fuel cell power systems (IEC 62282-3-201:2017/AMD1:2022)
Hardcopy , PDF
English
04-04-2022
10-12-2025
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols
5 Configuration of small stationary fuel cell power system
6 Reference conditions
7 Heating value base
8 Test preparation
9 Test set-up
10 Instruments and measurement methods
11 Test conditions
12 Operating process
13 Test plan
14 Type tests on electric/thermal performance
15 Type tests on environmental performance
16 Test reports
Annex A (normative) Heating values for components of natural gases
Annex B (informative) Examples of composition for natural gases and propane gases
Annex C (informative) Example of a test operation schedule
Annex D (informative) Typical exhaust gas components
Annex E (informative) Guidelines for the contents of detailed and full reports
Annex F (informative) Selected duration of rated power operation
Bibliography
This part of IEC 62282 provides test methods for the electrical, thermal and environmental performance of small stationary fuel cell power systems that meet the following criteria: • output: rated electric power output of less than 10 kW; • output mode: grid-connected/independent operation or stand-alone operation with singlephase AC output or 3-phase AC output not exceeding 1 000 V, or DC output not exceeding 1 500 V; NOTE The limit of 1 000 V for alternating current comes from the definition for "low voltage" given in IEC 60050-601:1985, 601-01-26.
| Committee |
TC 105
|
| DocumentType |
Test Method
|
| ISBN |
978-2-8322-1071-0
|
| Pages |
200
|
| ProductNote |
This standard also refers to ISO 6326,ISO 80000,SAE ARP 1533A-2004 The date of any NSAI previous adoption may not match the date of its original CEN/CENELEC document.
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| IEC 62282-3-201:2017/AMD1:2022 | Identical |
| ISO/TR 15916:2015 | Basic considerations for the safety of hydrogen systems |
| IEC 61672-2:2013+AMD1:2017 CSV | Electroacoustics - Sound level meters - Part 2: Pattern evaluation tests |
| IEC 60050-601:1985 | International Electrotechnical Vocabulary (IEV) - Part 601: Generation, transmission and distribution of electricity - General |
| IEC TS 62282-1:2013 | Fuel cell technologies - Part 1: Terminology |
| ISO 6975:1997 | Natural gas — Extended analysis — Gas-chromatographic method |
| ISO 7941:1988 | Commercial propane and butane — Analysis by gas chromatography |
| ISO 7935:1992 | Stationary source emissions — Determination of the mass concentration of sulfur dioxide — Performance characteristics of automated measuring methods |
| ISO 6976:1995 | Natural gas — Calculation of calorific values, density, relative density and Wobbe index from composition |
| ISO 6060:1989 | Water quality — Determination of the chemical oxygen demand |
| ISO 11042-1:1996 | Gas turbines — Exhaust gas emission — Part 1: Measurement and evaluation |
| ISO 11042-2:1996 | Gas turbines — Exhaust gas emission — Part 2: Automated emission monitoring |
| ISO 11564:1998 | Stationary source emissions — Determination of the mass concentration of nitrogen oxides — Naphthylethylenediamine photometric method |
| ISO 11541:1997 | Natural gas — Determination of water content at high pressure |
| IEC 61672-1:2013 | Electroacoustics - Sound level meters - Part 1: Specifications |
| ISO 9000:2015 | Quality management systems — Fundamentals and vocabulary |
| ISO 5815-2:2003 | Water quality — Determination of biochemical oxygen demand after n days (BODn) — Part 2: Method for undiluted samples |
| ISO 10849:1996 | Stationary source emissions — Determination of the mass concentration of nitrogen oxides — Performance characteristics of automated measuring systems |
| ISO 10523:2008 | Water quality — Determination of pH |
| ISO 10396:2007 | Stationary source emissions — Sampling for the automated determination of gas emission concentrations for permanently-installed monitoring systems |
| ISO 6798:1995 | Reciprocating internal combustion engines — Measurement of emitted airborne noise — Engineering method and survey method |
| ISO 7934:1989 | Stationary source emissions — Determination of the mass concentration of sulfur dioxide — Hydrogen peroxide/barium perchlorate/Thorin method |
| ISO 6974:1984 | Natural gas — Determination of hydrogen, inert gases and hydrocarbons up to C8 — Gas chromatographic method |
Access your standards online with a subscription
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Important note : Users cannot be edited or removed once added to your Multi user PDF.