Preview

I.S. EN 62811:2015

Current

Current The latest, up-to-date edition.

AC AND/OR DC-SUPPLIED ELECTRONIC CONTROLGEAR FOR DISCHARGE LAMPS (EXCLUDING FLUORESCENT LAMPS) - PERFORMANCE REQUIREMENTS FOR LOW FREQUENCY SQUAREWAVE OPERATION

Available format(s): Hardcopy, PDF

Language(s): English

Published date: 01-01-2015

Publisher: National Standards Authority of Ireland

Preview

For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

Dates of withdrawal of national standards are available from NSAI.

Table of Contents - (Show below) - (Hide below)

FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 General notes on tests
5 Marking
6 General statement
7 Starting conditions
8 Operating conditions
9 Displacement factor
10 Supply current
11 Endurance
Annex A (normative) - Tests
Annex B (normative) - Reference ballasts
Annex C (normative) - Conditions for reference lamps
Annex D (normative) Control interface for controllable
        Controlgear
Annex E (normative) - Spectral analysis of power ripple:
        calculation procedure for amplitude spectrum
        ratio and guidance
Annex F (normative) - Open circuit voltage method of
        measurement for pulse ignition
Bibliography
Annex ZA (normative) - Normative references to
         international publications with their
         corresponding European publications

Abstract - (Show below) - (Hide below)

Describes performance requirements for electronic controlgear for use on a.c. and/or d.c. supplies up to 1000 V and/or a.c. supplies up to 1 000 V at 50 Hz or 60 Hz, associated with discharge lamps, as specified in IEC 61167, which have information for low frequency square wave operation, where the frequency range of the low frequency is from 70 Hz to 400 Hz.

General Product Information - (Show below) - (Hide below)

Development Note	For CENELEC adoptions of IEC publications, please check www.iec.ch to be sure that you have any corrigenda that may apply. (01/2017)
Document Type	Standard
ISBN
Pages
Published
Publisher	National Standards Authority of Ireland
Status	Current

International Equivalents – Equivalent Standard(s) & Relationship - (Show below) - (Hide below)

Equivalent Standard(s)	Relationship
EN 62811:2015	Identical

Standards Referencing This Book - (Show below) - (Hide below)

IEC 61000-4-30 : 3.0EN+(REDLINE+VERSION)	ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-30: TESTING AND MEASUREMENT TECHNIQUES - POWER QUALITY MEASUREMENT METHODS
IEC 61547:2009	Equipment for general lighting purposes - EMC immunity requirements
IEC 61347-1:2015 RLV	Lamp controlgear - Part 1: General and safety requirements
EN 61000-4-14:1999/A2:2009	ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-14: TESTING AND MEASUREMENT TECHNIQUES - VOLTAGE FLUCTUATION IMMUNITY TEST FOR EQUIPMENT WITH INPUT CURRENT NOT EXCEEDING 16 A PER PHASE
IEC 61167:2015	Metal halide lamps - Performance specification
IEC 60410:1973	Sampling plans and procedures for inspection by attributes
EN 61347-1:2015	Lamp controlgear - Part 1: General and safety requirements
IEC 61347-2-12:2005+AMD1:2010 CSV	Lamp controlgear - Part 2-12: Particular requirements for d.c. or a.c. supplied electronic ballasts for discharge lamps (excluding fluorescent lamps)
IEC 61000-4-14:1999+AMD1:2001+AMD2:2009 CSV	Electromagnetic compatibility (EMC) - Part 4-14: Testing and measurement techniques - Voltage fluctuation immunity test for equipment with input current not exceeding 16 A per phase
IEC 61000-3-2 : 4.0	ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 3-2: LIMITS - LIMITS FOR HARMONIC CURRENT EMISSIONS (EQUIPMENT INPUT CURRENT <= 16 A PER PHASE)

Categories associated with this Standard - (Show below) - (Hide below)

Sub-Categories associated with this Standard - (Show below) - (Hide below)

Add To Cart

Product Format

Quantity

Buy now

Add to cart

Create account