I.S. EN ISO 10439:2002
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
PETROLEUM, CHEMICAL AND GAS SERVICE INDUSTRIES - CENTRIFUGAL COMPRESSORS
Hardcopy , PDF
07-03-2015
I.S. EN ISO 10439-4:2015
I.S. EN ISO 10439-1:2015
I.S. EN ISO 10439-3:2015
I.S. EN ISO 10439-2:2015
English
01-01-2002
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Basic design
4.1 General
4.2 Casings
4.3 Interstage diaphragms and inlet guide vanes
4.4 Casing connections
4.5 External forces and moments
4.6 Rotating elements
4.7 Bearings and bearing housings
4.8 Shaft seals
4.9 Dynamics
4.10 'Lube' oil and seal oil systems
4.11 Materials
4.12 Nameplates and rotation arrows
5 Accessories
5.1 Drivers
5.2 Couplings and guards
5.3 Mounting plates
5.4 Controls and instrumentation
5.5 Piping and appurtenances
5.6 Special tools
6 Inspection, testing and preparation for shipment
6.1 General
6.2 Inspection
6.3 Testing
6.4 Preparation for shipment
7 Vendor data
7.1 General
7.2 Proposals
7.3 Contract data
Annex A (informative) Typical data sheets
Annex B (informative) Material specifications for
major component parts
Annex C (normative) Centrifugal compressor vendor
drawing and data requirements
Annex D (normative) Procedure for determination of
residual unbalance
Annex E (informative) Rotor dynamic logic diagrams
Annex F (informative) Centrifugal compressor nomenclature
Annex G (normative) Forces and moments
Annex H (informative) Inspector's checklist
Annex I (informative) Typical gas seal testing considerations
Annex J (informative) Application considerations for
active magnetic bearings
Annex ZA (normative) Normative references to international
publications with their relevant
European publications
Bibliography
Specifies requirements and gives recommendations for the design, materials, fabrication, inspection, testing and preparation for shipment of centrifugal compressors for use in the petroleum, chemical and gas service industries.
| DocumentType |
Standard
|
| Pages |
132
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| NBN EN ISO 10439 : 2003 | Identical |
| NEN EN ISO 10439 : 2002 | Identical |
| EN ISO 10439:2002 | Identical |
| UNI EN ISO 10439 : 2003 | Identical |
| BS EN ISO 10439:2002 | Identical |
| DIN EN ISO 10439:2004-02 | Identical |
| ISO 10439:2002 | Identical |
| NF EN ISO 10439 : 2003 | Identical |
| SN EN ISO 10439 : 2004 | Identical |
| NS EN ISO 10439 : 1ED 2002 | Identical |
| ISO 14691:2008 | Petroleum, petrochemical and natural gas industries — Flexible couplings for mechanical power transmission — General-purpose applications |
| IEC 60079-10:2002 | Electrical apparatus for explosive gas atmospheres - Part 10: Classification of hazardous areas |
| ASTM A 583 : 1993 : R1999 | Standard Specification for Cast Steel Wheels for Railway Service (Withdrawn 2004) |
| ASTM A 353/A353M : 2017 : REDLINE | Standard Specification for Pressure Vessel Plates, Alloy Steel, Double-Normalized and Tempered 9 % Nickel |
| ISO 7005-2:1988 | Metallic flanges — Part 2: Cast iron flanges |
| ISO 3744:2010 | Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Engineering methods for an essentially free field over a reflecting plane |
| ISO 10442:2002 | Petroleum, chemical and gas service industries Packaged, integrally geared centrifugal air compressors |
| ASTM A 537/A537M : 2013 | Standard Specification for Pressure Vessel Plates, Heat-Treated, Carbon-Manganese-Silicon Steel |
| NEMA SM 23-1991 (R1997, R2002) | STEAM TURBINES FOR MECHANICAL DRIVE SERVICE |
| ISO 10437:2003 | Petroleum, petrochemical and natural gas industries — Steam turbines — Special-purpose applications |
| ISO 9614-1:1993 | Acoustics — Determination of sound power levels of noise sources using sound intensity — Part 1: Measurement at discrete points |
| SAE AMS 4676 : 2017 | NICKEL-COPPER ALLOY, CORROSION-RESISTANT, BARS AND FORGINGS, 66.5NI - 3.0AL - 0.62TI - 28CU, HOT-FINISHED, PRECIPITATION HARDENABLE |
| ASME PV CODE 8 DIV 1 : 2017 | BOILER AND PRESSURE VESSEL CODE - RULES FOR CONSTRUCTION OF PRESSURE VESSELS DIVISION 1 |
| ASTM A 395/A395M : 1999 | Standard Specification for Ferritic Ductile Iron Pressure-Retaining Castings for Use at Elevated Temperatures |
| ASTM A 744/A744M : 2013 : REDLINE | Standard Specification for Castings, Iron-Chromium-Nickel, Corrosion Resistant, for Severe Service |
| ASTM A 553/A553M : 2017 : REDLINE | Standard Specification for Pressure Vessel Plates, Alloy Steel, Quenched and Tempered 7, 8, and 9 % Nickel |
| ASTM A 516/A516M : 2017 : REDLINE | Standard Specification for Pressure Vessel Plates, Carbon Steel, for Moderate- and Lower-Temperature Service |
| ASTM A 693 : 2016 : REDLINE | Standard Specification for Precipitation-Hardening Stainless and Heat-Resisting Steel Plate, Sheet, and Strip |
| ISO 1940-1:2003 | Mechanical vibration Balance quality requirements for rotors in a constant (rigid) state Part 1: Specification and verification of balance tolerances |
| EN ISO 10441:2007 | Petroleum, petrochemical and natural gas industries - Flexible couplings for mechanical power transmission - Special-purpose applications (ISO 10441:2007) |
| ISO 9614-2:1996 | Acoustics — Determination of sound power levels of noise sources using sound intensity — Part 2: Measurement by scanning |
| ISO 7-2:2000 | Pipe threads where pressure-tight joints are made on the threads Part 2: Verification by means of limit gauges |
| NFPA 496 : 2017 | PURGED AND PRESSURIZED ENCLOSURES FOR ELECTRICAL EQUIPMENT |
| ASTM B 29 : 2014 : REDLINE | Standard Specification for Refined Lead |
| ISO 5389:2005 | Turbocompressors — Performance test code |
| ASTM A 578/A578M : 2017 : REDLINE | Standard Specification for Straight-Beam Ultrasonic Examination of Rolled Steel Plates for Special Applications |
| ASTM A 414/A414M : 2014 : REDLINE | Standard Specification for Steel, Sheet, Carbon, and High-Strength, Low-Alloy for Pressure Vessels |
| ISA RP12.4 : 1996 | PRESSURIZED ENCLOSURES |
| ISO 3977-5:2001 | Gas turbines Procurement Part 5: Applications for petroleum and natural gas industries |
| ASTM A 351/A351M : 2016-05 | SPECIFICATION FOR CASTINGS, AUSTENITIC, FOR PRESSURE-CONTAINING PARTS |
| NACE MR 01 75 : 2003 | METALS FOR SULFIDE STRESS CRACKING AND STRESS CORROSION CRACKING RESISTANCE IN SOUR OILFIELD ENVIRONMENTS |
| ASME B1.20.1 : 2013(R2018) | PIPE THREADS, GENERAL PURPOSE (INCH) |
| EN ISO 13691:2002 | Petroleum and natural gas industries - High-speed special-purpose gear units (ISO 13691:2001) |
| API 670 : 2014 | MACHINERY PROTECTION SYSTEMS |
| ISO 8821:1989 | Mechanical vibration Balancing Shaft and fitment key convention |
| ISO 7-1:1994 | Pipe threads where pressure-tight joints are made on the threads Part 1: Dimensions, tolerances and designation |
| API 617 : 2014 | AXIAL AND CENTRIFUGAL COMPRESSORS AND EXPANDER-COMPRESSORS |
| EN ISO 3744:2010 | Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Engineering methods for an essentially free field over a reflecting plane (ISO 3744:2010) |
| ISO 13691:2001 | Petroleum and natural gas industries — High-speed special-purpose gear units |
| ASME B36.10M : 2015 | WELDED AND SEAMLESS WROUGHT STEEL PIPE |
| ASTM A 217/A217M : 2014 : REDLINE | Standard Specification for Steel Castings, Martensitic Stainless and Alloy, for Pressure-Containing Parts, Suitable for High-Temperature Service |
| ASTM E 125 : 1963 : R2003 | Standard Reference Photographs for Magnetic Particle Indications on Ferrous Castings |
| ASTM A 148/A148M : 2015-09 | SPECIFICATION FOR STEEL CASTINGS, HIGH STRENGTH, FOR STRUCTURAL PURPOSES |
| ISO 10441:2007 | Petroleum, petrochemical and natural gas industries Flexible couplings for mechanical power transmission Special-purpose applications |
| ASTM E 709 : 2015 : REDLINE | Standard Guide for Magnetic Particle Testing |
| EN ISO 10437:2003 | Petroleum, petrochemical and natural gas industries - Steam turbines - Special-purpose applications (ISO 10437:2003) |
| ASTM A 203/A203M : 2017 : REDLINE | Standard Specification for Pressure Vessel Plates, Alloy Steel, Nickel |
| EN ISO 3977-5:2003 | Gas turbines - Procurement - Part 5: Applications for petroleum and natural gas industries (ISO 3977-5:2001) |
| ASTM A 494/A494M : 2017-03 | SPECIFICATION FOR CASTINGS, NICKEL AND NICKEL ALLOY |
| ASTM A 522/A522M : 2014 : REDLINE | Standard Specification for Forged or Rolled 8 and 9% Nickel Alloy Steel Flanges, Fittings, Valves, and Parts for Low-Temperature Service |
| ASTM A 285/A285M : 2017 : REDLINE | Standard Specification for Pressure Vessel Plates, Carbon Steel, Low- and Intermediate-Tensile Strength |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.