Skip to content
Please enter a keyword to search
  • Preview

    I.S. EN ISO 11120:2015

    Current The latest, up-to-date edition.

    GAS CYLINDERS - REFILLABLE SEAMLESS STEEL TUBES OF WATER CAPACITY BETWEEN 150 L AND 3000 L - DESIGN, CONSTRUCTION AND TESTING (ISO 11120:2015)

    Available format(s):  Hardcopy, PDF

    Language(s):  English

    Published date:  01-01-2015

    Publisher:  National Standards Authority of Ireland

    For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
    Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

    Dates of withdrawal of national standards are available from NSAI.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    Introduction
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Symbols
    5 Inspection and testing
    6 Materials
    7 Design
    8 Construction and workmanship
    9 Type approval procedure
    10 Batch tests
    11 Tests on every tube
    12 Special requirements for tubes for embrittling gases
    13 Inspection certificate
    14 Marking
    Annex A (informative) - Typical chemistry groupings for
            seamless steel tubes
    Annex B (normative) - Ultrasonic examination
    Annex C (informative) - Description and evaluation of
            manufacturing imperfections and conditions for
            rejection of seamless steel tubes at time of
            final inspection by the manufacturer
    Annex D (informative) - Acceptance certificate
    Annex E (informative) - Type approval certificate
    Annex F (informative) - Bend stress calculation
    Bibliography

    Abstract - (Show below) - (Hide below)

    Describes minimum requirements for the material, design, construction and workmanship, manufacturing processes and tests at manufacture of refillable quenched and tempered seamless steel tubes of water capacities from 150 l up to and including 3000 l for compressed and liquefied gases exposed to extreme world-wide ambient temperatures normally between -50 degrees C and +65 degrees C.

    General Product Information - (Show below) - (Hide below)

    Document Type Standard
    Publisher National Standards Authority of Ireland
    Status Current
    Supersedes

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO 6506-3:2014 Metallic materials Brinell hardness test Part 3: Calibration of reference blocks
    ISO 10893-5:2011 Non-destructive testing of steel tubes Part 5: Magnetic particle inspection of seamless and welded ferromagnetic steel tubes for the detection of surface imperfections
    ISO 6506-1:2014 Metallic materials Brinell hardness test Part 1: Test method
    ISO 11114-1:2012 Gas cylinders Compatibility of cylinder and valve materials with gas contents Part 1: Metallic materials
    ISO 9712:2012 Non-destructive testing Qualification and certification of NDT personnel
    ISO 148-2:2016 Metallic materials — Charpy pendulum impact test — Part 2: Verification of testing machines
    ISO 10893-8:2011 Non-destructive testing of steel tubes Part 8: Automated ultrasonic testing of seamless and welded steel tubes for the detection of laminar imperfections
    ISO 6892-1:2016 Metallic materials Tensile testing Part 1: Method of test at room temperature
    ISO 148-1:2016 Metallic materials — Charpy pendulum impact test — Part 1: Test method
    ISO 21028-2:2004 Cryogenic vessels Toughness requirements for materials at cryogenic temperature Part 2: Temperatures between -80 degrees C and -20 degrees C
    ISO 148-3:2016 Metallic materials — Charpy pendulum impact test — Part 3: Preparation and characterization of Charpy V-notch test pieces for indirect verification of pendulum impact machines
    ISO 11114-4:2017 Transportable gas cylinders Compatibility of cylinder and valve materials with gas contents Part 4: Test methods for selecting steels resistant to hydrogen embrittlement
    ISO 6506-2:2017 Metallic materials Brinell hardness test Part 2: Verification and calibration of testing machines
    ISO 6406:2005 Gas cylinders Seamless steel gas cylinders Periodic inspection and testing
    ISO 10893-2:2011 Non-destructive testing of steel tubes Part 2: Automated eddy current testing of seamless and welded (except submerged arc-welded) steel tubes for the detection of imperfections
    ISO 10893-4:2011 Non-destructive testing of steel tubes Part 4: Liquid penetrant inspection of seamless and welded steel tubes for the detection of surface imperfections
    ISO 11117:2008 Gas cylinders Valve protection caps and valve guards Design, construction and tests
    ISO 13769:2007 Gas cylinders Stamp marking
    ISO 11439:2013 Gas cylinders — High pressure cylinders for the on-board storage of natural gas as a fuel for automotive vehicles
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective