Skip to content
Please enter a keyword to search
  • Preview

    I.S. EN ISO 11403-3:2014

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE MULTIPOINT DATA - PART 3: ENVIRONMENTAL INFLUENCES ON PROPERTIES (ISO 11403-3:2014)

    Available format(s):  Hardcopy, PDF

    Superseded date:  31-12-2021

    Language(s):  English

    Published date:  01-01-2014

    Publisher:  National Standards Authority of Ireland

    For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
    Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

    Dates of withdrawal of national standards are available from NSAI.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    Introduction
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Specimen preparation
    5 Conditioning
    6 Test requirements
    7 Presentation of data
    8 Precision
    Annex A (informative) - Information relating to certain
            test requirements
    Annex B (normative) - Chemicals for chemical resistance
            and environmental stress cracking resistance
            tests
    Bibliography

    Abstract - (Show below) - (Hide below)

    Defines test procedures for the acquisition and presentation of multipoint data which demonstrate the behaviour of plastics under the following environments: - prolonged exposure to heat; - liquid chemicals; - environmental stress cracking under a constant tensile stress; and - artificial weathering.

    General Product Information - (Show below) - (Hide below)

    Document Type Standard
    Publisher National Standards Authority of Ireland
    Status Superseded
    Superseded By
    Supersedes

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO 10350-2:2011 Plastics Acquisition and presentation of comparable single-point data Part 2: Long-fibre-reinforced plastics
    ISO 4892-1:2016 Plastics Methods of exposure to laboratory light sources Part 1: General guidance
    ISO 2578:1993 Plastics Determination of time-temperature limits after prolonged exposure to heat
    ISO 293:2004 Plastics — Compression moulding of test specimens of thermoplastic materials
    ISO 295:2004 Plastics — Compression moulding of test specimens of thermosetting materials
    ISO 10350-1:2017 Plastics — Acquisition and presentation of comparable single-point data — Part 1: Moulding materials
    ISO 10724-1:1998 Plastics — Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) — Part 1: General principles and moulding of multipurpose test specimens
    ISO 294-2:1996 Plastics Injection moulding of test specimens of thermoplastic materials Part 2: Small tensile bars
    ISO 4892-3:2016 Plastics Methods of exposure to laboratory light sources Part 3: Fluorescent UV lamps
    ISO 175:2010 Plastics Methods of test for the determination of the effects of immersion in liquid chemicals
    ISO 291:2008 Plastics Standard atmospheres for conditioning and testing
    ISO 4892-4:2013 Plastics — Methods of exposure to laboratory light sources — Part 4: Open-flame carbon-arc lamps
    ISO 4892-2:2013 Plastics — Methods of exposure to laboratory light sources — Part 2: Xenon-arc lamps
    ISO 294-1:2017 Plastics — Injection moulding of test specimens of thermoplastic materials — Part 1: General principles, and moulding of multipurpose and bar test specimens
    ISO 2818:1994 Plastics — Preparation of test specimens by machining
    ISO 11403-1:2014 Plastics Acquisition and presentation of comparable multipoint data Part 1: Mechanical properties
    ISO 20753:2008 Plastics Test specimens
    ISO 527-1:2012 Plastics Determination of tensile properties Part 1: General principles
    ISO 1817:2015 Rubber, vulcanized or thermoplastic Determination of the effect of liquids
    ISO 10724-2:1998 Plastics — Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) — Part 2: Small plates
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective