I.S. EN ISO 13679:2006
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
PETROLEUM AND NATURAL GAS INDUSTRIES - PROCEDURES FOR TESTING CASING AND TUBING CONNECTIONS
Hardcopy , PDF
14-09-2019
English
01-01-2006
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms, definitions, symbols and abbreviated terms
3.1 Terms and definitions
3.2 Symbols and abbreviated terms
4 General requirements
4.1 Connection geometry, test load envelope and performance
data sheet
4.2 Quality control
5 General test
5.1 Test classes
5.2 Test matrix
5.3 Test programme
5.4 Calibration and accreditation requirements
5.5 Rehearsal tests
5.6 Material property tests
5.7 Make-up and break-out procedures
5.8 Internal pressure leak detection
5.9 Internal pressure leak trap device
5.10 External pressure leak detection
5.11 Data acquisition and test methods
5.12 Thermal cycling tests
6 Connection test specimen preparation
6.1 General connection test objectives
6.2 Connection test specimen identification and marking
6.3 Connection test specimen preparation
6.4 Connection test specimen machining
6.5 Machining tolerances
6.6 Tolerance limits on machining objectives
6.7 Grooved torque shoulder
7 Test procedures
7.1 Principle
7.2 Make-up/break-out tests
7.3 Test load envelope tests
7.4 Limit load tests
7.5 Limit load test path
8 Acceptance criteria
8.1 Make-up and break-out tests
8.2 Test load envelope tests
8.3 Limit load tests
9 Test reports
Annex A (normative) Connection geometry and performance
data sheet
Annex B (informative) Connection test load envelope and
limit loads
Annex C (normative) Data forms
Annex D (normative) Connection full test report
Annex E (normative) Connection testing summary report
Annex F (informative) Frame load range determination
Annex G (informative) Interpolation and extrapolation
considerations
Annex H (informative) Special application testing
Annex I (informative) Rationale for design basis
Annex J (normative) Independent seal testing of connections
with metal-to-metal and resilient seals
Bibliography
Presents minimum design verification testing procedures and acceptance criteria for casing and tubing connections for the oil and natural gas industries.
| DocumentType |
Standard
|
| Pages |
152
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| ISO 13679:2002 | Identical |
| ONORM EN ISO 13679 : 2007 | Identical |
| SN EN ISO 13679 : 2007 | Identical |
| NS EN ISO 13679 : 1ED 2007 | Identical |
| DIN EN ISO 13679:2010-10 (Draft) | Identical |
| NF EN ISO 13679 : 2009 | Identical |
| UNI EN ISO 13679 : 2007 | Identical |
| BS EN ISO 13679:2006 | Identical |
| NBN EN ISO 13679 : 2007 | Identical |
| NEN EN ISO 13679 : 2006 | Identical |
| EN ISO 13679:2006 | Identical |
| ISO 13680:2010 | Petroleum and natural gas industries Corrosion-resistant alloy seamless tubes for use as casing, tubing and coupling stock Technical delivery conditions |
| ISO 10400:1993 | Petroleum and natural gas industries — Formulae and calculation for casing, tubing, drill pipe and line pipe properties |
| ISO 3183-3:1999 | Petroleum and natural gas industries — Steel pipe for pipelines — Technical delivery conditions — Part 3: Pipes of requirement class C |
| API 5CT : 2012 | CASING AND TUBING |
| ISO 3183-2:1996 | Petroleum and natural gas industries — Steel pipe for pipelines — Technical delivery conditions — Part 2: Pipes of requirements class B |
| API 5L : 2012 | LINE PIPE |
| API 5C3 : 1994 | BULLETIN ON FORMULAS AND CALCULATIONS FOR CASING, TUBING, DRILL PIPE AND LINE PIPE PROPERTIES |
| ISO 10422:1993 | Petroleum and natural gas industries — Threading, gauging, and thread inspection of casing, tubing and line pipe threads — Specification |
| ISO 3183-1:1996 | Petroleum and natural gas industries — Steel pipe for pipelines — Technical delivery conditions — Part 1: Pipes of requirement class A |
| API 5C5 : 2017 | PROCEDURES FOR TESTING CASING AND TUBING CONNECTIONS |
| ISO 11960:2014 | Petroleum and natural gas industries Steel pipes for use as casing or tubing for wells |
| ISO/IEC Guide 22:1996 | General criteria for supplier's declaration of conformity |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.