I.S. EN ISO 15876-5:2017
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
PLASTICS PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS - POLYBUTENE (PB) - PART 5: FITNESS FOR PURPOSE OF THE SYSTEM (ISO 15876-5:2017)
Hardcopy , PDF
18-01-2021
English
01-01-2017
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
National Foreword
European foreword
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions, symbols
and abbreviated terms
4 Fitness for purpose of the joints
and the piping system
Bibliography
Describes the characteristics of the fitness for purpose of polybutene-1 (PB-1) piping systems, intended to be used for hot and cold water installations within buildings for the conveyance of water, whether or not intended for human consumption, (domestic systems) and for heating systems, under design pressures and temperatures according to the class of application.
| DocumentType |
Standard
|
| Pages |
26
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| UNE-EN ISO 15876-5:2017 | Identical |
| ISO 15876-5:2017 | Identical |
| SN EN ISO 15876-5 : 2017 | Identical |
| DIN EN ISO 15876-5:2015-08 (Draft) | Identical |
| NEN EN ISO 15876-5 : 2017 | Identical |
| NS EN ISO 15876-5 : 2017 | Identical |
| BS EN ISO 15876-5:2017 | Identical |
| NBN EN ISO 15876-5 : 2004 | Identical |
| UNI EN ISO 15876-5 : 2005 | Identical |
| EN ISO 15876-5:2017 | Identical |
| NF EN ISO 15876-5 : 2017 | Identical |
| ONORM EN ISO 15876-5 : 2018 | Identical |
| ISO 19892:2011 | Plastics piping systems Thermoplastics pipes and fittings for hot and cold water Test method for the resistance of joints to pressure cycling |
| ISO 1167-2:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 2: Preparation of pipe test pieces |
| ISO 13056:2011 | Plastics piping systems Pressure systems for hot and cold water Test method for leaktightness under vacuum |
| ISO 1167-4:2007 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 4: Preparation of assemblies |
| ISO 3501:2015 | Plastics piping systems Mechanical joints between fittings and pressure pipes Test method for resistance to pull-out under constant longitudinal force |
| ISO 19893:2011 | Plastics piping systems Thermoplastics pipes and fittings for hot and cold water Test method for the resistance of mounted assemblies to temperature cycling |
| ISO/TS 15876-7:2003 | Plastics piping systems for hot and cold water installations Polybutylene (PB) Part 7: Guidance for the assessment of conformity |
| ISO 15876-1:2017 | Plastics piping systems for hot and cold water installations — Polybutene (PB) — Part 1: General |
| ISO 15876-3:2017 | Plastics piping systems for hot and cold water installations — Polybutene (PB) — Part 3: Fittings |
| ISO 1167-3:2007 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 3: Preparation of components |
| CEN/TR 12108:2012 | Plastics piping systems - Guidance for the installation inside buildings of pressure piping systems for hot and cold water intended for human consumption |
| ISO 15876-2:2017 | Plastics piping systems for hot and cold water installations — Polybutene (PB) — Part 2: Pipes |
| ISO 3503:2015 | Plastics piping systems Mechanical joints between fittings and pressure pipes Test method for leaktightness under internal pressure of assemblies subjected to bending |
| ISO 1167-1:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 1: General method |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.