• I.S. EN ISO 23936-1:2009

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

    PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - NON-METALLIC MATERIALS IN CONTACT WITH MEDIA RELATED TO OIL AND GAS PRODUCTION - PART 1: THERMOPLASTICS

    Available format(s):  Hardcopy, PDF

    Superseded date:  06-05-2023

    Language(s):  English

    Published date:  01-01-2009

    Publisher:  National Standards Authority of Ireland

    For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
    Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

    Dates of withdrawal of national standards are available from NSAI.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    Introduction
    1 Scope
    2 Normative references
    3 Terms, definitions and abbreviated terms
      3.1 Terms and definitions
      3.2 Abbreviated terms
    4 Functional requirements
      4.1 General
      4.2 Pipelines, piping and liners
      4.3 Seals, washers and gaskets
      4.4 Encapsulations, electrical insulations, injection
          lines
    5 Requirements for technical information
    6 Requirements for manufacturers
      6.1 General requirements
      6.2 Raw material manufacturer
      6.3 Component manufacturer
      6.4 Validity of qualification
    7 Qualification of thermoplastic materials
      7.1 General
      7.2 Requirements for chemical resistance tests
    Annex A (informative) - Typical chemical properties of
            commonly used thermoplastic materials in media
            encountered in oil and gas production
    Annex B (normative) - Test media, conditions, equipment,
            procedures and test report requirements
    Bibliography

    Abstract - (Show below) - (Hide below)

    Describes general principles and gives requirements and recommendations for the selection and qualification, and gives guidance for the quality assurance, of non-metallic materials for service in equipment used in oil and gas production environments, where the failure of such equipment could pose a risk to the health and safety of the public and personnel or to the environment.

    General Product Information - (Show below) - (Hide below)

    Document Type Standard
    Publisher National Standards Authority of Ireland
    Status Superseded
    Superseded By

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO 2578:1993 Plastics Determination of time-temperature limits after prolonged exposure to heat
    NACE TM 01 87 : 2011 EVALUATING ELASTOMERIC MATERIALS IN SOUR GAS ENVIRONMENTS
    ISO/TS 29001:2010 Petroleum, petrochemical and natural gas industries Sector-specific quality management systems Requirements for product and service supply organizations
    ISO 1874-1:2010 Plastics Polyamide (PA) moulding and extrusion materials Part 1: Designation system and basis for specification
    ISO 13628-1:2005 Petroleum and natural gas industries — Design and operation of subsea production systems — Part 1: General requirements and recommendations
    ISO 13628-2:2006 Petroleum and natural gas industries Design and operation of subsea production systems Part 2: Unbonded flexible pipe systems for subsea and marine applications
    ISO 1873-2:2007 Plastics Polypropylene (PP) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties
    ISO 13628-9:2000 Petroleum and natural gas industries — Design and operation of subsea production systems — Part 9: Remotely Operated Tool (ROT) intervention systems
    API TR 17TR2 : 2003 THE AGEING OF PA-11 IN FLEXIBLE PIPES
    ISO 13628-3:2000 Petroleum and natural gas industries — Design and operation of subsea production systems — Part 3: Through flowline (TFL) systems
    ISO 16770:2004 Plastics Determination of environmental stress cracking (ESC) of polyethylene Full-notch creep test (FNCT)
    ASTM D 543 : 2014 : REDLINE Standard Practices for Evaluating the Resistance of Plastics to Chemical Reagents
    ASTM D 3032 : 2016 : REDLINE Standard Test Methods for Hookup Wire Insulation
    ISO 11357-5:2013 Plastics — Differential scanning calorimetry (DSC) — Part 5: Determination of characteristic reaction-curve temperatures and times, enthalpy of reaction and degree of conversion
    ASTM D 792 : 2013 : REDLINE Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement
    ISO 14692-4:2017 Petroleum and natural gas industries — Glass-reinforced plastics (GRP) piping — Part 4: Fabrication, installation and operation
    ISO 846:1997 Plastics Evaluation of the action of microorganisms
    ISO 13628-11:2007 Petroleum and natural gas industries — Design and operation of subsea production systems — Part 11: Flexible pipe systems for subsea and marine applications
    API SPEC 17J : 2014 SPECIFICATION FOR UNBONDED FLEXIBLE PIPE
    ISO 11357-3:2011 Plastics Differential scanning calorimetry (DSC) Part 3: Determination of temperature and enthalpy of melting and crystallization
    ISO 1874-2:2012 Plastics Polyamide (PA) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties
    ISO 11357-2:2013 Plastics Differential scanning calorimetry (DSC) Part 2: Determination of glass transition temperature and glass transition step height
    ISO 11357-4:2014 Plastics Differential scanning calorimetry (DSC) Part 4: Determination of specific heat capacity
    ISO 15156-2:2015 Petroleum and natural gas industries Materials for use in H2S-containing environments in oil and gas production Part 2: Cracking-resistant carbon and low-alloy steels, and the use of cast irons
    ISO 15156-3:2015 Petroleum and natural gas industries Materials for use in H2S-containing environments in oil and gas production Part 3: Cracking-resistant CRAs (corrosion-resistant alloys) and other alloys
    ISO 14692-1:2017 Petroleum and natural gas industries — Glass-reinforced plastics (GRP) piping — Part 1: Vocabulary, symbols, applications and materials
    ISO 13628-7:2005 Petroleum and natural gas industries — Design and operation of subsea production systems — Part 7: Completion/workover riser systems
    ISO 15750-3:2002 Packaging Steel drums Part 3: Inserted flange-type closure systems
    ISO 175:2010 Plastics Methods of test for the determination of the effects of immersion in liquid chemicals
    ISO 14692-2:2017 Petroleum and natural gas industries — Glass-reinforced plastics (GRP) piping — Part 2: Qualification and manufacture
    EN 579:1993 Plastics piping systems - Crosslinked polyethylene (PE-X) pipes - Determination of degree of crosslinking by solvent extraction
    ISO 1183-1:2012 Plastics Methods for determining the density of non-cellular plastics Part 1: Immersion method, liquid pyknometer method and titration method
    ISO 14001:2015 Environmental management systems — Requirements with guidance for use
    ISO 177:2016 Plastics Determination of migration of plasticizers
    ISO 1872-2:2007 Plastics Polyethylene (PE) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties
    ISO 176:2005 Plastics — Determination of loss of plasticizers — Activated carbon method
    ISO 1183-2:2004 Plastics Methods for determining the density of non-cellular plastics Part 2: Density gradient column method
    ISO 1183-3:1999 Plastics Methods for determining the density of non-cellular plastics Part 3: Gas pyknometer method
    ISO 9001:2015 Quality management systems — Requirements
    ISO 15156-1:2015 Petroleum and natural gas industries Materials for use in H2S-containing environments in oil and gas production Part 1: General principles for selection of cracking-resistant materials
    ISO 13628-6:2006 Petroleum and natural gas industries Design and operation of subsea production systems Part 6: Subsea production control systems
    ISO 179-1:2010 Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test
    ISO 13628-4:2010 Petroleum and natural gas industries — Design and operation of subsea production systems — Part 4: Subsea wellhead and tree equipment
    ISO 62:2008 Plastics Determination of water absorption
    ISO 11357-6:2008 Plastics Differential scanning calorimetry (DSC) Part 6: Determination of oxidation induction time (isothermal OIT) and oxidation induction temperature (dynamic OIT)
    ISO 306:2013 Plastics — Thermoplastic materials — Determination of Vicat softening temperature (VST)
    ISO 13628-8:2002 Petroleum and natural gas industries — Design and operation of subsea production systems — Part 8: Remotely Operated Vehicle (ROV) interfaces on subsea production systems
    ASTM D 695 : 2015 : REDLINE Standard Test Method for Compressive Properties of Rigid Plastics
    ISO 13628-5:2009 Petroleum and natural gas industries Design and operation of subsea production systems Part 5: Subsea umbilicals
    ISO 11357-1:2016 Plastics — Differential scanning calorimetry (DSC) — Part 1: General principles
    ISO 178:2010 Plastics Determination of flexural properties
    ISO 14692-3:2017 Petroleum and natural gas industries — Glass-reinforced plastics (GRP) piping — Part 3: System design
    ASTM D 2990 : 2017 : REDLINE Standard Test Methods for Tensile, Compressive, and Flexural Creep and Creep-Rupture of Plastics
    ISO 1133:2005 Plastics Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics
    ASTM D 638 : 2014 : REDLINE Standard Test Method for Tensile Properties of Plastics
    ASTM D 746 : 2014 : REDLINE Standard Test Method for Brittleness Temperature of Plastics and Elastomers by Impact
    ISO 527-1:2012 Plastics Determination of tensile properties Part 1: General principles
    ISO 13623:2017 Petroleum and natural gas industries — Pipeline transportation systems
    ISO 868:2003 Plastics and ebonite — Determination of indentation hardness by means of a durometer (Shore hardness)
    ASTM D 1693 : 2015 : REDLINE Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics
    ISO 13628-10:2005 Petroleum and natural gas industries — Design and operation of subsea production systems — Part 10: Specification for bonded flexible pipe
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective