Skip to content
Please enter a keyword to search
  • Preview

    I.S. EN ISO 3506-2:2009

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    MECHANICAL PROPERTIES OF CORROSION-RESISTANT STAINLESS STEEL FASTENERS - PART 2: NUTS

    Available format(s):  Hardcopy, PDF

    Superseded date:  16-05-2020

    Language(s):  English

    Published date:  01-01-2009

    Publisher:  National Standards Authority of Ireland

    For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
    Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

    Dates of withdrawal of national standards are available from NSAI.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    Introduction
    1 Scope
    2 Normative references
    3 Symbols
    4 Designation, marking and finish
    5 Chemical composition
    6 Mechanical properties
    7 Test methods
    Annex A (informative) - Description of the groups and grades
                            of stainless steels
    Annex B (informative) - Stainless steel composition
                            specifications
    Annex C (informative) - Stainless steels for cold heading
                            and extruding
    Annex D (informative) - Austenitic stainless steels with
                            particular resistance to chloride
                            induced stress corrosion
    Annex E (informative) - Mechanical properties at elevated
                            temperatures; application at low
                            temperatures
    Annex F (informative) - Time-temperature diagram of
                            intergranular corrosion in austenitic
                            stainless steels, grade A2 (18/8
                            steels)
    Annex G (informative) - Magnetic properties for austenitic
                            stainless steels
    Bibliography

    Abstract - (Show below) - (Hide below)

    Describes the mechanical properties of nuts made of austenitic, martensitic and ferritic steel grades of corrosion-resistant stainless steels, when tested over an ambient temperature range of 10 degrees C to 35 degrees C.

    General Product Information - (Show below) - (Hide below)

    Document Type Standard
    Publisher National Standards Authority of Ireland
    Status Superseded
    Superseded By
    Supersedes

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO 272:1982 Fasteners — Hexagon products — Widths across flats
    ISO 6507-1:2005 Metallic materials Vickers hardness test Part 1: Test method
    ISO 898-2:2012 Mechanical properties of fasteners made of carbon steel and alloy steel — Part 2: Nuts with specified property classes — Coarse thread and fine pitch thread
    ISO 6506-1:2014 Metallic materials Brinell hardness test Part 1: Test method
    ISO 683-13:1974 Heat-treated steels, alloy steels and free-cutting steels Part 13: Wrought stainless steels
    ISO 6508-1:2016 Metallic materials — Rockwell hardness test — Part 1: Test method
    ISO 16426:2002 Fasteners — Quality assurance system
    ISO 898-6:1994 Mechanical properties of fasteners Part 6: Nuts with specified proof load values Fine pitch thread
    ISO 262:1998 ISO general purpose metric screw threads — Selected sizes for screws, bolts and nuts
    ISO 68-1:1998 ISO general purpose screw threads — Basic profile — Part 1: Metric screw threads
    ISO 3651-2:1998 Determination of resistance to intergranular corrosion of stainless steels — Part 2: Ferritic,austenitic and ferritic-austenitic (duplex) stainless steels — Corrosion test in media containing sulfuric acid
    ISO 8044:2015 Corrosion of metals and alloys Basic terms and definitions
    ISO 16048:2003 Passivation of corrosion-resistant stainless-steel fasteners
    ISO 3651-1:1998 Determination of resistance to intergranular corrosion of stainless steels — Part 1: Austenitic and ferritic-austenitic (duplex) stainless steels — Corrosion test in nitric acid medium by measurement of loss in mass (Huey test)
    ISO 261:1998 ISO general purpose metric screw threads General plan
    EN 10088-1:2014 Stainless steels - Part 1: List of stainless steels
    ISO 4954:1993 Steels for cold heading and cold extruding
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective