I.S. EN ISO 5270:2012
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
PULPS - LABORATORY SHEETS - DETERMINATION OF PHYSICAL PROPERTIES (ISO 5270:2012)
Hardcopy , PDF
06-05-2023
English
01-01-2012
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Foreword
Introduction
1 Scope
2 Normative references
3 Principle
4 Apparatus
5 Trimmed laboratory sheets
6 Procedures for physical properties
("low grammage" sheets)
7 Procedures for physical properties
("high grammage" sheets)
8 Test report
Bibliography
Describes the relevant International Standards to be used for the determination of physical properties of laboratory sheets made of all kind of pulps.
| DocumentType |
Standard
|
| Pages |
23
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| NEN EN ISO 5270 : 2012 | Identical |
| UNI EN ISO 5270 : 2012 | Identical |
| BS EN ISO 5270:2012 | Identical |
| EN ISO 5270:2012 | Identical |
| ISO 5270:2012 | Identical |
| SN EN ISO 5270 : 2012 | Identical |
| UNE-EN ISO 5270:2013 | Identical |
| DIN EN ISO 5270:2013-02 | Identical |
| NBN EN ISO 5270 : 2012 | Identical |
| NF EN ISO 5270 : 2012 | Identical |
| NS EN ISO 5270 : 2012 | Identical |
| ONORM EN ISO 5270 : 2013 | Identical |
| ISO 5269-1:2005 | Pulps — Preparation of laboratory sheets for physical testing — Part 1: Conventional sheet-former method |
| ISO 2493-1:2010 | Paper and board Determination of bending resistance Part 1: Constant rate of deflection |
| ISO 1974:2012 | Paper — Determination of tearing resistance — Elmendorf method |
| ISO 5636-3:2013 | Paper and board — Determination of air permeance (medium range) — Part 3: Bendtsen method |
| ISO 5636-4:2013 | Paper and board — Determination of air permeance (medium range) — Part 4: Sheffield method |
| ISO 11476:2016 | Paper and board Determination of CIE whiteness, C/2 (indoor illumination conditions) |
| ISO 1924-3:2005 | Paper and board Determination of tensile properties Part 3: Constant rate of elongation method (100 mm/min) |
| ISO 7263:2011 | Corrugating medium Determination of the flat crush resistance after laboratory fluting |
| ISO 5626:1993 | Paper Determination of folding endurance |
| ISO 2493-2:2011 | Paper and board Determination of bending resistance Part 2: Taber-type tester |
| ISO 2471:2008 | Paper and board — Determination of opacity (paper backing) — Diffuse reflectance method |
| ISO 9895:2008 | Paper and board — Compressive strength — Short-span test |
| ISO 15361:2000 | Pulps Determination of zero-span tensile strength, wet or dry |
| ISO 2758:2014 | Paper Determination of bursting strength |
| ISO 187:1990 | Paper, board and pulps — Standard atmosphere for conditioning and testing and procedure for monitoring the atmosphere and conditioning of samples |
| ISO 5628:2012 | Paper and board — Determination of bending stiffness — General principles for two-point, three-point and four-point methods |
| ISO 2470-1:2016 | Paper, board and pulps Measurement of diffuse blue reflectance factor Part 1: Indoor daylight conditions (ISO brightness) |
| ISO 5636-5:2013 | Paper and board — Determination of air permeance (medium range) — Part 5: Gurley method |
| ISO 1924-2:2008 | Paper and board — Determination of tensile properties — Part 2: Constant rate of elongation method (20 mm/min) |
| ISO 11475:2017 | Paper and board — Determination of CIE whiteness, D65/10 degrees (outdoor daylight) |
| ISO 536:2012 | Paper and board Determination of grammage |
| ISO 12192:2011 | Paper and board — Determination of compressive strength — Ring crush method |
| ISO 534:2011 | Paper and board — Determination of thickness, density and specific volume |
| ISO 5269-3:2008 | Pulps — Preparation of laboratory sheets for physical testing — Part 3: Conventional and Rapid-Köthen sheet formers using a closed water system |
| ISO 3688:1999 | Pulps — Preparation of laboratory sheets for the measurement of diffuse blue reflectance factor (ISO brightness) |
| ISO 9416:2017 | Paper — Determination of light scattering and absorption coefficients (using Kubelka-Munk theory) |
| ISO 15754:2009 | Paper and board Determination of z-directional tensile strength |
| ISO 5269-2:2004 | Pulps — Preparation of laboratory sheets for physical testing — Part 2: Rapid-Köthen method |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.