I.S. EN ISO 5395-3:2013
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
GARDEN EQUIPMENT - SAFETY REQUIREMENTS FOR COMBUSTION-ENGINE-POWERED LAWNMOWERS - PART 3: RIDE-ON LAWNMOWERS WITH SEATED OPERATOR (ISO 5395-3:2013)
Hardcopy , PDF
28-01-2020
English
19-09-2013
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
National Foreword
European foreword
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Requirements for ride-on lawnmowers
5 Particular requirements for ride-on rotary lawnmowers
6 Particular requirements for ride-on cylinder lawnmowers
7 Information for use
Annex A (normative) - Ride-on lawnmower stability test
Annex B (normative) - Determination of contact with moving
power-driven components
Annex C (informative) - List of significant hazards
Bibliography
Annex ZA (informative) - Relationship between this
European standard and the Essential Requirements
of EU Directive 2006/42/EC amended by
Directive 2009/127/EC aimed to be covered
Describes safety requirements and their verification for combustion-engine- powered ride-on (seated) rotary lawnmowers and cylinder lawnmowers (hereafter named 'lawnmower').
| Committee |
TC 23
|
| DevelopmentNote |
Supersedes I.S. EN 836. (09/2013)
|
| DocumentType |
Standard
|
| Pages |
57
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| EN ISO 5395-3:2013 | Identical |
| ISO 5395-3:2013 | Identical |
| ISO 14119:2013 | Safety of machinery — Interlocking devices associated with guards — Principles for design and selection |
| ISO 17398:2004 | Safety colours and safety signs — Classification, performance and durability of safety signs |
| ISO/TR 11688-1:1995 | Acoustics Recommended practice for the design of low-noise machinery and equipment Part 1: Planning |
| ISO 3776-3:2009 | Tractors and machinery for agriculture Seat belts Part 3: Requirements for assemblies |
| ISO 5353:1995 | Earth-moving machinery, and tractors and machinery for agriculture and forestry Seat index point |
| ISO/TS 15079:2001 | Powered lawn, garden and horticultural equipment — Operator controls — Guidance on actuating forces, displacement, location and methods of operation |
| ISO 3776-2:2013 | Tractors and machinery for agriculture — Seat belts — Part 2: Anchorage strength requirements |
| ISO 3600:2015 | Tractors, machinery for agriculture and forestry, powered lawn and garden equipment — Operator's manuals — Content and format |
| ISO 21299:2009 | Powered ride-on turf care equipment Roll-over protective structures (ROPS) Test procedures and acceptance criteria |
| ISO 12100:2010 | Safety of machinery — General principles for design — Risk assessment and risk reduction |
| CR 1030-1:1995 | Hand-arm vibration - Guidelines for vibration hazards reduction - Part 1: Engineering methods by design of machinery |
| ISO 11820:1996 | Acoustics — Measurements on silencers in situ |
| ISO 14982:1998 | Agricultural and forestry machinery Electromagnetic compatibility Test methods and acceptance criteria |
| ISO 5395-1:2013 | Garden equipment — Safety requirements for combustion-engine-powered lawnmowers — Part 1: Terminology and common tests |
| ISO 13857:2008 | Safety of machinery Safety distances to prevent hazard zones being reached by upper and lower limbs |
| ISO 14163:1998 | Acoustics — Guidelines for noise control by silencers |
| IEC 61032:1997 | Protection of persons and equipment by enclosures - Probes for verification |
| ISO 13849-1:2015 | Safety of machinery — Safety-related parts of control systems — Part 1: General principles for design |
| ISO/TR 11688-2:1998 | Acoustics Recommended practice for the design of low-noise machinery and equipment Part 2: Introduction to the physics of low-noise design |
| ISO 11691:1995 | Acoustics Measurement of insertion loss of ducted silencers without flow Laboratory survey method |
| ISO 11684:1995 | Tractors, machinery for agriculture and forestry, powered lawn and garden equipment — Safety signs and hazard pictorials — General principles |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.