I.S. EN ISO 6892-1:2016
Withdrawn
A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.
View Superseded by
METALLIC MATERIALS - TENSILE TESTING - PART 1: METHOD OF TEST AT ROOM TEMPERATURE (ISO 6892-1:2016)
Hardcopy , PDF
30-06-2020
English
01-01-2016
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
National Foreword
European Foreword
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols
5 Principle
6 Test pieces
7 Determination of original cross-sectional area
8 Original gauge length and extensometer gauge
length
9 Accuracy of testing apparatus
10 Conditions of testing
11 Determination of the upper yield strength
12 Determination of the lower yield strength
13 Determination of proof strength, plastic extension
14 Determination of proof strength, total extension
15 Method of verification of permanent set strength
16 Determination of the percentage yield point extension
17 Determination of the percentage plastic extension at
maximum force
18 Determination of the percentage total extension at
maximum force
19 Determination of the percentage total extension at
fracture
20 Determination of percentage elongation after fracture
21 Determination of percentage reduction of area
22 Test report
23 Measurement uncertainty
Annex A (informative) - Recommendations concerning the
use of computer-controlled tensile testing machines
Annex B (normative) - Types of test pieces to be used for
thin products: sheets, strips and flats between
0,1 mm and 3 mm thick
Annex C (normative) - Types of test pieces to be used for
wire, bars and sections with a diameter
or thickness of less than 4 mm
Annex D (normative) - Types of test pieces to be used for
sheets and flats of thickness equal to or
greater than 3 mm, and wire, bars
and sections of diameter or thickness
equal to or greater than 4 mm
Annex E (normative) - Types of test pieces to be used
for tubes
Annex F (informative) - Estimation of the crosshead
separation rate in consideration of the stiffness
(or compliance) of the testing equipment
Annex G (normative) - Determination of the modulus of
elasticity of metallic materials using a
uniaxial tensile test
Annex H (informative) - Measuring the percentage
elongation after fracture if the specified value
is less than 5%
Annex I (informative) - Measurement of percentage
elongation after fracture based on subdivision
of the original gauge length
Annex J (informative) - Determination of the percentage
plastic elongation without necking, A[wn], for
long products such as bars, wire, and rods
Annex K (informative) - Estimation of the uncertainty of
measurement
Annex L (informative) - Precision of tensile testing
- Results from interlaboratory programmes
Bibliography
Describes the method for tensile testing of metallic materials and defines the mechanical properties which can be determined at room temperature.
| DevelopmentNote |
Supersedes I.S. EN 10002-1. (09/2009)
|
| DocumentType |
Standard
|
| Pages |
96
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Withdrawn
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| EN ISO 6892-1:2016 | Identical |
| ISO 6892-1:2016 | Identical |
| I.S. 328:2015/AC1:2015 | GAS TRANSMISSION PIPELINES AND PIPELINE INSTALLATIONS (EDITION 4) |
| I.S. 328:2015 | GAS TRANSMISSION PIPELINES AND PIPELINE INSTALLATIONS (EDITION 4) |
| SEP 1235 : 2012 | BESTIMMUNG DES ELASTIZITAETSMODULS AN STAHL IM ZUGVERSUCH BEI RAUMTEMPERATUR |
| ISO/TTA 2:1997 | Tensile tests for discontinuously reinforced metal matrix composites at ambient temperatures |
| ISO 2566-2:1984 | Steel Conversion of elongation values Part 2: Austenitic steels |
| ISO 3183:2012 | Petroleum and natural gas industries Steel pipe for pipeline transportation systems |
| ISO 9513:2012 | Metallic materials — Calibration of extensometer systems used in uniaxial testing |
| ASTM E 8M : 2004 | Standard Test Methods for Tension Testing of Metallic Materials [Metric] (Withdrawn 2008) |
| ISO/TR 25679:2005 | Mechanical testing of metals Symbols and definitions in published standards |
| ISO 2566-1:1984 | Steel Conversion of elongation values Part 1: Carbon and low alloy steels |
| ISO 80000-1:2009 | Quantities and units — Part 1: General |
| ASTM E 111 : 2017 : REDLINE | Standard Test Method for Young’s Modulus, Tangent Modulus, and Chord Modulus |
| ISO 7500-1:2015 | Metallic materials Calibration and verification of static uniaxial testing machines Part 1: Tension/compression testing machines Calibration and verification of the force-measuring system |
| ISO 377:2017 | Steel and steel products — Location and preparation of samples and test pieces for mechanical testing |
| EN 10291 : 2000 | METALLIC MATERIALS - UNIAXIAL CREEP TESTING IN TENSION - METHOD OF TEST |
| ISO 11960:2014 | Petroleum and natural gas industries Steel pipes for use as casing or tubing for wells |
| ISO/IEC Guide 98-3:2008 | Uncertainty of measurement — Part 3: Guide to the expression of uncertainty in measurement (GUM:1995) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.