Skip to content
Please enter a keyword to search
  • Preview

    I.S. EN ISO 7866:2012

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    GAS CYLINDERS - REFILLABLE SEAMLESS ALUMINIUM ALLOY GAS CYLINDERS - DESIGN, CONSTRUCTION AND TESTING (ISO 7866:2012)

    Available format(s):  Hardcopy, PDF

    Superseded date:  01-02-2021

    Language(s):  English

    Published date:  19-09-2012

    Publisher:  National Standards Authority of Ireland

    For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
    Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

    Dates of withdrawal of national standards are available from NSAI.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    Introduction
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Symbols
    5 Inspection and testing
    6 Materials
    7 Design
    8 Construction and workmanship
    9 Type approval procedure
    10 Batch tests
    11 Gas cylinder tests and examinations
    12 Certification
    13 Marking
    Annex A (normative) - Corrosion tests
    Annex B (normative) - Test method to determine the
            sustained-load cracking resistance of
            aluminium alloy gas cylinders
    Annex C (informative) - Typical type approval certificate
    Annex D (informative) - Acceptance certificate
    Annex E (normative) - Specific requirements for gas
            cylinders made of high-strength and/or
            low-elongation aluminium alloy
    Annex F (informative) - Description and evaluation of
            manufacturing surface imperfections and conditions
            for rejection of seamless aluminium alloy gas
            cylinders at time of product acceptance
    Annex G (normative) - Batch size
    Annex H (normative) - Specific provisions for acetylene
            cylinder shells
    Bibliography

    Abstract - (Show below) - (Hide below)

    Describes minimum requirements for the material, design, construction and workmanship, manufacturing processes and tests at time of manufacture of refillable seamless aluminium alloy gas cylinders of water capacities up to and including 150 litres for compressed, liquefied and dissolved gases for worldwide use (normally up to +65 degrees C).

    General Product Information - (Show below) - (Hide below)

    Development Note Supersedes I.S. EN 1975. (10/2012)
    Document Type Standard
    Publisher National Standards Authority of Ireland
    Status Superseded
    Superseded By
    Supersedes

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO 6506-1:2014 Metallic materials Brinell hardness test Part 1: Test method
    ISO 209:2007 Aluminium and aluminium alloys — Chemical composition
    ISO 11114-1:2012 Gas cylinders Compatibility of cylinder and valve materials with gas contents Part 1: Metallic materials
    ISO 6508-1:2016 Metallic materials — Rockwell hardness test — Part 1: Test method
    ISO 6892-1:2016 Metallic materials Tensile testing Part 1: Method of test at room temperature
    ISO 13341:2010 Gas cylinders — Fitting of valves to gas cylinders
    ISO 11363-1:2010 Gas cylinders 17E and 25E taper threads for connection of valves to gas cylinders Part 1: Specifications
    ISO 7438:2016 Metallic materials Bend test
    ISO 7539-6:2011 Corrosion of metals and alloys Stress corrosion testing Part 6: Preparation and use of precracked specimens for tests under constant load or constant displacement
    ISO 9809-2:2010 Gas cylinders Refillable seamless steel gas cylinders Design, construction and testing Part 2: Quenched and tempered steel cylinders with tensile strength greater than or equal to 1 100 MPa
    ISO 10461:2005 Gas cylinders Seamless aluminium-alloy gas cylinders Periodic inspection and testing
    ISO 11363-2:2017 Gas cylinders — 17E and 25E taper threads for connection of valves to gas cylinders — Part 2: Inspection gauges
    ISO 11117:2008 Gas cylinders Valve protection caps and valve guards Design, construction and tests
    ISO 13769:2007 Gas cylinders Stamp marking
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective