IEC 60034-2A:1974
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Rotating electrical machines - Part 2: Methods for determining losses and efficiency of rotating electrical machinery form tests (excluding machines for traction vehicles) - Measurement of losses by the calorimetric method
Hardcopy , PDF , PDF 3 Users , PDF 5 Users , PDF 9 Users
27-06-2014
English - French, Russian
01-01-1974
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Foreword
Preface
Introduction
3.1 List of symbols
Section One - General
1. General
2. Determination of loss P1 by measurement of the volume rate
of flow and rise in temperature of the cooling medium
3. Losses P1 measured electrically using the calorimetric
calibration method
4. Stable conditions
5. Losses P2 not transmitted to the cooling medium
6. Lossses external to the reference surface Pe
Section Two - Wate as the Cooling Medium
7. Application and basic relationship
8. Measurement of water flow
9. Measurement of the temperature rise of the water
10. Measuring accuracy
Section Three - Air as the Cooling Medium
11. Application and basic relationship
12. Determination of the mass rate of flow
13. Measurement of the temperature rise of the air
14. Determination of the specific heat capacity of the air
15. Measuring accuracy
Section Four - Practical Considerations
16. Preparations for calormetric measurements with liquid coolants
17. Connections and equipment for calorimetric measurements
with liquid coolants
Figures
Describes methods for measuring the efficiency of electrical rotating machines either by determining total losses on load or by determination of the segregated losses for air and water cooling mediums. Applies to large generators but may be used for other machines.
| Committee |
TC 2
|
| DocumentType |
Standard
|
| Pages |
36
|
| PublisherName |
International Electrotechnical Committee
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| NBN C 51 102 : 1979 | Identical |
| BS 4999-102:1987 | Identical |
| AS 1359.102.2-1997 | Corresponds |
| NEN 10034-2 : 1997 AMD 2 1997 | Identical |
| HD 53-2 : 200S1 | Identical |
| VDE 0530-2 : 1998 | Identical |
| DIN EN ISO 5802:2016-02 | INDUSTRIAL FANS - PERFORMANCE TESTING IN SITU (ISO 5802:2001 + AMD 1:2015) |
| NF EN 61116 : 2003 | ELECTROMECHANICAL EQUIPMENT GUIDE FOR SMALL HYDROELECTRIC INSTALLATIONS |
| CEI EN 61116 : 1996 | ELECTROMECHANICAL EQUIPMENT GUIDE FOR SMALL HYDROELECTRIC INSTALLATIONS |
| I.S. EN 61116:1995 | ELECTROMECHANICAL EQUIPMENT GUIDE FOR SMALL HYDROELECTRIC INSTALLATIONS |
| IEC 60034-4:2008 | Rotating electrical machines - Part 4: Methods for determining synchronous machine quantities from tests |
| 12/30248232 DC : DRAFT AUG 2012 | BS EN 61400-2 - WIND TURBINES - PART 2: SMALL WIND TURBINES |
| UNI CEI EN 45510-2-5 : 2011 | GUIDE FOR PROCUREMENT OF POWER STATION EQUIPMENT - PART 2-5: ELECTRICAL EQUIPMENT - MOTORS |
| BS EN ISO 5802 : 2008 | INDUSTRIAL FANS - PERFORMANCE TESTING IN SITU |
| CEI EN 60034-4 : 2009 | ROTATING ELECTRICAL MACHINES - PART 4: METHODS FOR DETERMINING SYNCHRONOUS MACHINE QUANTITIES FROM TESTS |
| NF EN 60034-4 : 2008 | ROTATING ELECTRICAL MACHINES - PART 4: METHODS FOR DETERMINING SYNCHRONOUS MACHINE QUANTITIES FROM TESTS |
| BS 848-3(2001) : 2001 | FANS FOR GENERAL PURPOSE - PART 3: PERFORMANCE TESTING IN SITU |
| CEI EN 60041 : 1997 | FIELD ACCEPTANCE TESTS TO DETERMINE THE HYDRAULIC PERFORMANCE OF HYDRAULIC TURBINES, STORAGE PUMPS AND PUMP-TURBINES |
| IEC TS 60034-23:2003 | Rotating electrical machines - Part 23: Specification for the refurbishing of rotating electrical machines |
| ISO 5802:2001 | Industrial fans — Performance testing in situ |
| IEC 61800-4:2002 | Adjustable speed electrical power drive systems - Part 4: General requirements - Rating specifications for a.c. power drive systems above 1 000 V a.c. and not exceeding 35 kV |
| BS EN 61800-4:2003 | Adjustable speed electrical power drive systems General requirements. Rating specifications for a.c. power drive systems above 1000 V a.c. and not exceeding 35 kV |
| 01/202922 DC : DRAFT APR 2001 | IEC 60034-23 ED.1 - ROTATING ELECTRICAL MACHINES - PART 23: SPECIFICATION FOR THE REFURBISHING OF ROTATING ELECTRICAL MACHINES |
| IEC 61116:1992 | Electromechanical equipment guide for small hydroelectric installations |
| 16/30295473 DC : 0 | BS ISO 8528-7 - RECIPROCATING INTERNAL COMBUSTION ENGINE DRIVEN ALTERNATING CURRENT GENERATING SETS - PART 7: TECHNICAL DECLARATIONS FOR SPECIFICATION AND DESIGN |
| BS EN 60034-4:2008 | Rotating electrical machines Methods for determining synchronous machine quantities from tests |
| CEI EN 61800-4 : 2003 | ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 4: GENERAL REQUIREMENTS - RATING SPECIFICATIONS FOR A/C/ POWER DRIVE SYSTEMS ABOVE 1000 V A.C. AND NOT EXCEEDING 35 KV |
| I.S. EN ISO 5802:2008 | INDUSTRIAL FANS - PERFORMANCE TESTING IN SITU (ISO 5802:2001) |
| I.S. EN 60034-4:2008 | ROTATING ELECTRICAL MACHINES - PART 4: METHODS FOR DETERMINING SYNCHRONOUS MACHINE QUANTITIES FROM TESTS |
| I.S. EN 61800-4:2003 | ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 4: GENERAL REQUIREMENTS - RATING SPECIFICATIONS FOR A.C. POWER DRIVE SYSTEMS ABOVE 1000 V A.C. AND NOT EXCEEDING 35 KV |
| EN 61800-4:2003 | Adjustable speed electrical power drive systems - Part 4: General requirements - Rating specifications for a.c. power drive systems above 1 000 V a.c. and not exceeding 35 kV |
| EN 61116:1994 | Electromechanical equipment guide for small hydroelectric installations |
| EN 60034-4:2008 | Rotating electrical machines - Part 4: Methods for determining synchronous machine quantities from tests |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.