IEC 60317-4:2015
Withdrawn
A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.
Specifications for particular types of winding wires - Part 4: Solderable polyurethane enamelled round copper wire, class 130
Hardcopy , PDF , PDF 3 Users , PDF 5 Users , PDF 9 Users
04-01-2022
English - French
09-06-2015
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms, definitions, general notes and appearance
4 Dimensions
5 Electrical resistance
6 Elongation
7 Springiness
8 Flexibility and adherence
9 Heat shock
10 Cut-through
11 Resistance to abrasion (nominal conductor diameters
from 0,250 mm up to and including 2,000 mm)
12 Resistance to solvents
13 Breakdown voltage
14 Continuity of insulation
15 Temperature index
16 Resistance to refrigerants
17 Solderability
18 Heat or solvent bonding
19 Dielectric dissipation factor
20 Resistance to transformer oil
21 Loss of mass
23 Pin hole test
30 Packaging
Bibliography
IEC 60317-4:2015 specifies the requirements of solderable enamelled round copper winding wire of class 130 with a sole coating based on polyurethane resin, which may be modified provided it retains the chemical identity of the original resin and meets all specified wire requirements. The range of nominal conductor diameters covered by this standard is:
- Grade 1: 0,018 mm up to and including 2,000 mm;
- Grade 2: 0,020 mm up to and including 2,000 mm. The nominal conductor diameters are specified in Clause 4 of IEC 60317-0-1:2013. This fourth edition cancels and replaces the third edition published in 1990, Amendment 1:1997 and Amendment 2:1999. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
- new 3.2.2 containing general notes on winding wire, formerly a part of the scope;
- new 3.2.3 containing requirements for appearance;
- revision to references to IEC 60317-0-1:2013 to clarify that their application is normative;
- consolidation of 17.1 and 17.2 of the solderability requirements;
- revision to Clause 19, dielectric dissipation factor;
- new Clause 23, pin hole test. Keywords: insulated wires used for windings
This publication is to be read in conjunction with IEC 60317-0-1:2013.
Committee |
TC 55
|
DevelopmentNote |
be read in conjunction with IEC 60317-0-1. Stability date: 2019. (06/2015)
|
DocumentType |
Standard
|
Pages |
20
|
PublisherName |
International Electrotechnical Committee
|
Status |
Withdrawn
|
Supersedes |
Standards | Relationship |
BS IEC 60317-4:2015 | Identical |
IS 13730 : Part 4 : 2018 | Identical |
I.S. EN 60317-4:1996 | Identical |
NEN EN IEC 60317-4 : 1995 AMD 2 2000 | Identical |
DIN 46416-2 : 1977 | Similar to |
NFC 31 602 : 1982 | Similar to |
UNE 21179-4:1993 | Identical |
UNE-EN 60317-4:1995 | Identical |
CEI EN 60317-4 : 2013 | Identical |
DIN IEC 60317-4:2015-01 (Draft) | Similar to |
NEN 10317-4 : 1995 | Similar to |
BIS IS 13730-4 : 2013 | Identical |
EN 60317-4:1994/A2:2000 | Identical |
I.S. EN 61858:2008 | ELECTRICAL INSULATION SYSTEMS - THERMAL EVALUATION OF MODIFICATIONS TO AN ESTABLISHED WIRE-WOUND EIS |
EN 60317-11 : 2000 | SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - BUNCHED SOLDERABLE POLYURETHANE ENAMELLED ROUND COPPER WIRE, CLASS 130, WITH SILK COVERING |
EN 61248-4:1997 | Transformers and inductors for use in electronic and telecommunication equipment - Part 4: Sectional specification for power transformers for switched mode power supplies (SMPS) on the basis of the capability approval procedure |
BS EN 61021-2:1997 | Laminated core packages for transformers and inductors for use in telecommunication and electronic equipment Electrical characteristics for cores using YEE 2 laminations |
I.S. EN 61248-4:1998 | TRANSFORMERS AND INDUCTORS FOR USE IN ELECTRONIC AND TELECOMMUNICATION EQUIPMENT - PART 4: SECTIONAL SPECIFICATION FOR POWER TRANSFORMERS FOR SWITCHED MODE POWER SUPPLIES (SMPS) ON THE BASIS OF THE CAPABILITY APPROVAL PROCEDURE |
I.S. EN 60317-11:1995 | SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 11: BUNCHED SOLDERABLE POLYURETHANE ENAMELLED ROUND COPPER WIRES, CLASS 130, WITH SILK COVERING |
NF EN 61858 : 2009 | ELECTRICAL INSULATION SYSTEMS - THERMAL EVALUATION OF MODIFICATIONS TO AN ESTABLISHED WIRE-WOUND EIS |
12/30273916 DC : 0 | BS EN 61858-1 - ELECTRICAL INSULATION SYSTEMS - THERMAL EVALUATION OF MODIFICATIONS TO AN ESTABLISHED EIS - PART-1: WIRE-WOUND WINDING EIS |
BS EN 61858-1:2014 | Electrical insulation systems. Thermal evaluation of modifications to an established electrical insulation system (EIS) Wire-wound winding EIS |
BS EN 61858:2008 | Electrical insulation systems. Thermal evaluation of modifications to an established wire-wound EIS |
IEC 60034-18-22:2000 | Rotating electrical machines - Part 18-22: Functional evaluation of insulation systems - Test procedures for wire-wound windings - Classification of changes and insulation component substitutions |
IEC 60317-11:1999+AMD1:2005 CSV | Specifications for particular types of winding wires - Part 11: Bunched solderable polyurethane enamelled round copper wires, class 130, with silk covering |
I.S. EN 61858-1:2014 | ELECTRICAL INSULATION SYSTEMS - THERMAL EVALUATION OF MODIFICATIONS TO AN ESTABLISHED ELECTRICAL INSULATION SYSTEM (EIS) - PART 1: WIRE-WOUND WINDING EIS |
BS EN 60317-11:2000 | Specifications for particular types of winding wires Bunched solderable polyurethane enamelled round copper wires, class 130, with silk covering |
IEC 61021-2:1995 | Laminated core packages for transformers and inductors for use in telecommunication and electronic equipment - Part 2: Electrical characteristics for cores using YEE2 laminations |
IEC 61858-1:2014 | Electrical insulation systems - Thermal evaluation of modifications to an established electrical insulation system (EIS) - Part 1: Wire-wound winding EIS |
IEC 61248-4:1996 | Transformers and inductors for use in electronic andtelecommunication equipment - Part 4: Sectional specification forpower transformers for switched mode power supplies (SMPS) on thebasis of the capability approval procedure |
IEC 61858:2008 | Electrical insulation systems - Thermal evaluation of modifications to an established wire-wound EIS |
EN 61858-1:2014 | Electrical insulation systems - Thermal evaluation of modifications to an established electrical insulation system (EIS) - Part 1: Wire-wound winding EIS |
EN 61858:2008 | ELECTRICAL INSULATION SYSTEMS - THERMAL EVALUATION OF MODIFICATIONS TO AN ESTABLISHED WIRE-WOUND EIS |
IEC 60317-0-1:2013 | Specifications for particular types of winding wires - Part 0-1: General requirements - Enamelled round copper wire |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.