• IEC 60317-0-1:2013

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

    Specifications for particular types of winding wires - Part 0-1: General requirements - Enamelled round copper wire

    Available format(s):  Hardcopy, PDF, PDF 3 Users, PDF 5 Users, PDF 9 Users

    Superseded date:  28-08-2019

    Language(s):  Spanish, Castilian

    Published date:  07-10-2013

    Publisher:  International Electrotechnical Committee

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    FOREWORD
    INTRODUCTION
    1 Scope
    2 Normative references
    3 Terms, definitions, general notes and
       appearance
    4 Dimensions
    5 Electrical resistance
    6 Elongation
    7 Springiness
    8 Flexibility and adherence
    9 Heat shock
    10 Cut-through
    11 Resistance to abrasion
    12 Resistance to solvents
    13 Breakdown voltage
    14 Continuity of insulation (nominal conductor
       diameters up to and including 1,600 mm)
    15 Temperature index
    16 Resistance to refrigerants
    17 Solderability
    18 Heat or solvent bonding
    19 Dielectric dissipation factor
    20 Resistance to transformer oil
    21 Loss of mass
    23 Pin hole test
    30 Packaging
    Annex A (informative) - Dimensions for intermediate
            nominal conductor diameters (R 40)
    Annex B (informative) - Method for the calculation
            of linear resistance
    Annex C (informative) - Resistance
    Bibliography

    Abstract - (Show below) - (Hide below)

    IEC 60317-0-1:2013 specifies general requirements of enamelled round copper winding wires with or without bonding layer. The range of nominal conductor diameters is given in the relevant specification sheet. This fourth edition cancels and replaces the third edition published in 2008. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:

    - revision to the definition of nominal conductor dimension;

    - new subclause containing general notes on winding wire, formerly a part of the scope;

    - revision to elongation requirements in Table 4;

    - revisions to Clause 13, Breakdown voltage, to include new requirements for intermediate wire diameters;

    - revision to continuity of insulation requirements in Table 13;

    - revision to the introduction of Annex A;

    - revision to B.2 of Annex B;

    - revision to Table C.1 of Annex C. Keywords: requirements of enamelled round copper winding wires



    This publication is to be read in conjunction with the IEC 60851 series.

    General Product Information - (Show below) - (Hide below)

    Committee TC 55
    Development Note Supersedes IEC 60182-1, IEC 60182-2, IEC 60182-4 (03/2001) To be read in conjunction with the IEC 60851 series. (03/2008) Stability date: 2019. (09/2017)
    Document Type Standard
    Publisher International Electrotechnical Committee
    Status Superseded
    Superseded By
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    11/30248410 DC : DRAFT JUNE 2011 BS EN 60317-38 - SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 38: POLYESTER OR POLYESTERIMIDE OVERCOATED WITH POLYAMIDE-IMIDE, ENAMELLED ROUND COPPER WIRE, CLASS 200, WITH A BONDING LAYER
    BS EN 60317-0-6 : 2001 SPECIFICATION FOR PARTICULAR TYPES OF WINDING WIRES - PART 0-6: GENERAL REQUIREMENTS - GLASS-FIBRE WOUND RESIN OR VARNISH IMPREGNATED, BARE OR ENAMELLED ROUND COPPER WIRE
    11/30248380 DC : DRAFT JUNE 2011 BS EN 60317-20 - SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 20: SOLDERABLE POLYURETHANE ENAMELLED ROUND COPPER WIRE, CLASS 155
    CEI EN 60317-23 : 2014 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 23: SOLDERABLE POLYESTERIMIDE ENAMELLED ROUND COPPER WIRE, CLASS 180
    CEI EN 60317-55 : 2014 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 55: SOLDERABLE POLYURETHANE ENAMELLED ROUND COPPER WIRE OVERCOATED WITH POLYAMIDE, CLASS 180
    NF EN 60317-0-7 : 2017 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 0-7: GENERAL REQUIREMENTS - FULLY INSULATED (FIW) ZERO-DEFECT ENAMELLED ROUND COPPER WIRE
    13/30285568 DC : 0 BS EN 60317-4 - SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 4: SOLDERABLE POLYURETHANE ENAMELLED ROUND COPPER WIRE, CLASS 130
    BIS IS 13730-13 : 2014 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 13: POLYESTER OR POLYESTERIMIDE OVERCOATED WITH POLYAMIDE-IMIDE ENAMELLED ROUND COPPER WIRE, CLASS 200
    NBR ISO 5744 : 2011 PLIERS AND NIPPERS - METHODS OF TEST
    08/30189113 DC : 0 BS EN 60317-57 - SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 57: POLYAMIDE-IMIDE ENAMELED ROUND COPPER WIRE, CLASS 220
    IEC 60317-54:2001 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 54: POLYESTER ENAMELLED ROUND COPPER WIRE, CLASS 155L
    BS EN 60317-59 : 2016 SPECIFICATIONS FOR PARTICULAR TYPE OF WINDING WIRES - PART 59: POLYAMIDEIMIDE ENAMELED ROUND COPPER WIRE, CLASS 240
    BS PD IEC TS 62332-3 : 2016 ELECTRICAL INSULATION SYSTEMS (EIS) - THERMAL EVALUATION OF COMBINED LIQUID AND SOLID COMPONENTS - PART 3: HERMETIC MOTOR-COMPRESSORS
    CEI EN 60317-38 : 2014 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 38: POLYESTER OR POLYESTERIMIDE OVERCOATED WITH POLYAMIDE-IMIDE ENAMELLED ROUND COPPER WIRE, CLASS 200, WITH A BONDING LAYER
    BS EN 60317-12 : 2010 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 12: POLYVINYL ACETAL ENAMELLED ROUND COPPER WIRE, CLASS 120
    BS 6811-3.1(1993) : 1993 AMD 8886 WINDING WIRES - SPECIFICATIONS FOR PARTICULAR TYPES OF ROUND COPPERS WINDING WIRES - POLYVINYL ACETAL ENAMELLED ROUND COPPER WIRE, CLASS 105
    BS 6811-3.8(1993) : 1993 AMD 8891 WINDING WIRES - SPECIFICATIONS FOR PARTICULAR TYPES OF ENAMELLED ROUND COPPER WINDING WIRES - POLYIMIDE ENAMELLED ROUND COPPER WIRE, CLASS 220
    BS 6811-3.9(1993) : 1993 AMD 9059 WINDING WIRES - SPECIFICATIONS FOR PARTICULAR TYPES OF ENAMELLED ROUND COPPER WINDING WIRES - SOLDERABLE POLYURETHANE ENAMELLED ROUND COPPER WIRE, CLASS 155
    CEI EN 60317-37 : 2014 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 37: POLYESTERIMIDE ENAMELLED ROUND COPPER WIRE, CLASS 180, WITH A BONDING LAYER
    BS 6811-3.3(1993) : 1993 AMD 8888 WINDING WIRES - SPECIFICATIONS FOR PARTICULAR TYPES OF ROUND COPPER WINDING WIRES - POLYIMIDE ENAMELLED ROUND COPPER WIRE, CLASS 220
    CEI EN 60317-19 : 2000 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 19: SOLDERABLE POLYURETHANE ENAMELLED ROUND COPPER WIRE OVERCOATED WITH POLYAMIDE, CLASS 130
    04/300396 DC : DRAFT JAN 2004 IEC 61347-1 A2 ED.1 - LAMP CONTROLGEAR - PART 1: GENERAL AND SAFETY REQUIREMENTS
    11/30249312 DC : 0 BS EN 60317-36 - SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 36: SOLDERABLE POLYESTERIMIDE ENAMELLED ROUND COPPER WIRE, CLASS 180, WITH A BONDING LAYER
    09/30200517 DC : 0 BS EN 60317-13 ED.3 - SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 13: POLYESTER OR POLYESTERIMIDE OVERCOATED WITH POLYAMIDE-IMIDE ENAMELLED ROUND COPPER WIRE, CLASS 200
    09/30200487 DC : 0 BS EN 60317-8 ED.4 - SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 8: POLYESTERIMIDE ENAMELLED ROUND COPPER WIRE, CLASS 180
    BS EN 60317-26 : 1997 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 26: POLYAMIDE-IMIDE ENAMELLED ROUND COPPER WIRE, CLASS 200
    11/30249511 DC : 0 BS EN 60317-46:1997/A1 - SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 46: AROMATIC POLYIMIDE ENAMELLED ROUND COPPER WIRES, CLASS 240
    NF EN 61347-1 : 2015 LAMP CONTROLGEAR - PART 1: GENERAL AND SAFETY REQUIREMENTS
    BS 6811-3.13(1993) : 1993 AMD 8588 WINDING WIRES - SPECIFICATIONS FOR PARTICULAR TYPES OF ENAMELLED ROUND COPPER WINDING WIRES - SOLDERABLE POLYURETHANE ENAMELLED ROUND COPPER WIRE, CLASS 155, WITH A BONDING LAYER
    BS EN 60317-45:1998 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 45: POLYESTER ENAMELLED ROUND COPPER WIRE, CLASS 130
    11/30249503 DC : 0 BS EN 60317-23 - SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 23: SOLDERABLE POLYESTERIMIDE ENAMELLED ROUND COPPER WIRE, CLASS 180
    CEI EN 60317-36 : 2014 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 36: SOLDERABLE POLYESTERIMIDE ENAMELLED ROUND COPPER WIRE, CLASS 180, WITH A BONDING LAYER
    11/30248402 DC : DRAFT JUNE 2011 BS EN 60317-37 - SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 37: POLYESTERIMIDE ENAMELLED ROUND COPPER WIRE, CLASS 180, WITH A BONDING LAYER
    UNI ISO 9656 : 2011 PLIERS AND NIPPERS FOR ELECTRONICS - TEST METHODS
    13/30282496 DC : 0 BS EN 60317-59 - SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 59: POLYAMIDE-IMIDE ENAMELED ROUND COPPER WIRE, CLASS 240
    UNE-EN 60317-57:2011 Specifications for particular types of winding wires -- Part 57: Polyamide-imide enamelled round copper wire, class 220
    DIN EN 60317-34:1997-10 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 34: POLYESTER ENAMELLED ROUND COPPER WIRE, CLASS 130 L
    09/30200572 DC : 0 BS EN 60317-26 A2 ED.2 - SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 26: POLYAMIDE-IMIDE ENAMELLED ROUND COPPER WIRE, CLASS 200
    BIS IS 13730-8 : 2014 SPECIFICATION FOR PARTICULAR TYPES OF WINDING WIRES - PART 8: POLYESTERIMIDE ENAMELLED ROUND COPPER WIRE, CLASS 180
    NF EN 60317-55 : 2014 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 55: SOLDERABLE POLYURETHANE ENAMELLED ROUND COPPER WIRE OVERCOATED WITH POLYAMIDE, CLASS 180
    BS EN 60317-0-7 : 2017 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 0-7: GENERAL REQUIREMENTS - FULLY INSULATED (FIW) ZERO-DEFECT ENAMELLED ROUND COPPER WIRE (IEC 60317-0-7:2017)
    IEC 60317-1:2010 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 1: POLYVINYL ACETAL ENAMELLED ROUND COPPER WIRE, CLASS 105
    I.S. EN 60317-57:2010 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 57: POLYAMIDE-IMIDE ENAMELLED ROUND COPPER WIRE, CLASS 220
    CEI EN 60317-12 : 2010 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 12: POLYVINYL ACETAL ENAMELLED ROUND COPPER WIRE, CLASS 120
    BS 6811-3.10(1993) : 1993 AMD 9064 WINDING WIRES - SPECIFICATIONS FOR PARTICULAR TYPES OF ENAMELLED ROUND COPPER WINDING WIRES - POLYESTER OR POLYESTERIMIDE ENAMELLED ROUND COPPER WIRE OVERCOATED WITH POLYAMIDE, CLASS 180
    CEI EN 60317-35 : 2014 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 35: SOLDERABLE POLYURETHANE ENAMELLED ROUND COPPER WIRE, CLASS 155, WITH A BONDING LAYER
    BS 6811-3.7(1993) : 1993 AMD 8890 WINDING WIRES - SPECIFICATIONS FOR PARTICULAR TYPES OF ENAMELLED ROUND COPPER WINDING WIRES - POLYVINYL ACETAL ENAMELLED ROUND COPPER WIRE, CLASS 120
    BS EN 60317-51 : 2014 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 51: SOLDERABLE POLYURETHANE ENAMELLED ROUND COPPER WIRE, CLASS 180
    11/30247067 DC : 0 BS EN 60317-2 - SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 2: SOLDERABLE POLYURETHANE ENAMELLED ROUND COPPER WIRE, CLASS 130, WITH A BONDING LAYER
    BS 6811-3.2(1993) : 1993 AMD 8887 WINDING WIRES - SPECIFICATIONS FOR PARTICULAR TYPES OF ROUND COPPER WINDING WIRES - SOLDERABLE POLYURETHANE ENAMELLED ROUND COPPER WIRE, CLASS 130, WITH A BONDING LAYER
    DIN EN 60317-1 : 95 AMD 1 97 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 1: POLYVINYL ACETAL ENAMELLED ROUND COPPER WIRE, CLASS 105
    12/30276801 DC : 0 BS EN 60317-52 ED 2.0 - SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 52: AROMATIC POLYAMIDE (ARAMID) TAPE WRAPPED ROUND COPPER WIRE, TEMPERATURE INDEX 220
    BS 6811-3.5(1993) : 1993 AMD 8889 WINDING WIRES - SPECIFICATIONS FOR PARTICULAR TYPES OF ENAMELLED ROUND COPPER WINDING WIRES - POLYVINYL ACETAL, ENAMELLED ROUND COPPER WIRE, CLASS 105
    09/30200498 DC : 0 BS EN 60317-12 ED.3 - SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 12: POLYVINYL ACETAL ENAMELLED ROUND COPPER WIRE, CLASS 120
    11/30248392 DC : DRAFT JUNE 2011 BS EN 60317-21 - SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 21: SOLDERABLE POLYURETHANE ENAMELLED ROUND COPPER WIRE OVER COATED WITH POLYAMIDE, CLASS 155
    CEI EN 61347-1 : 2016 LAMP CONTROLGEAR - PART 1: GENERAL AND SAFETY REQUIREMENTS
    08/30176410 DC : DRAFT JULY 2008 BS EN 60317-0-7 - SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 0-7: GENERAL REQUIREMENTS - FULLY INSULATED (FIW) ZERO-DEFECT ENAMELLED WINDING WIRES
    DIN EN 60317-4:2000-10 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 4: SOLDERABLE POLYURETHANE ENAMELLED ROUND COPPER WIRE, CLASS 130
    BS EN 60317-4 : 1995 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 4: SOLDERABLE POLYURETHANE ENAMELLED ROUND COPPER WIRE, CLASS 130
    CEI EN 60317-13 : 2010 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 13: POLYESTER OR POLYESTERIMIDE OVERCOATED WITH POLYAMIDE-IMIDE ENAMELLED ROUND COPPER WIRE, CLASS 200
    BS EN 60317-42 : 1997 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 42: POLYESTER-AMIDE-IMIDE ENAMELLED ROUND COPPER WIRE, CLASS 200
    09/30200413 DC : 0 BS EN 60317-1 ED.4 - SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 1: POLYVINYL ACETAL ENAMELLED ROUND COPPER WIRE, CLASS 105
    09/30200589 DC : 0 BS EN 60317-42 A1 ED.1 - SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 42: POLYESTER-AMIDE-IMIDE ENAMELLED ROUND COPPER WIRE, CLASS 200
    BS EN 60317-0-9 : 2015 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 0-9: GENERAL REQUIREMENTS - ENAMELLED RECTANGULAR ALUMINIUM WIRE
    BS EN 60317-46 : 2014 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 46: AROMATIC POLYIMIDE ENAMELED ROUND COPPER WIRE, CLASS 240
    BS ISO 9656:2004 Pliers and nippers for electronics. Test methods
    BS EN 60317-57 : 2010 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 57: POLYAMIDE-IMIDE ENAMELLED ROUND COPPER WIRE, CLASS 220
    BS 6811-3.11(1993) : 1993 AMD 9058 WINDING WIRES - SPECIFICATIONS FOR PARTICULAR TYPES OF ENAMELLED ROUND COPPER WINDING WIRES - SOLDERABLE POLYESTERIMIDE ENAMELLED ROUND COPPER WIRE, CLASS 180
    BS 6811-3.4(1993) : 1993 AMD 9063 WINDING WIRES - SPECIFICATIONS FOR PARTICULAR TYPES OF ENAMELLED ROUND COPPER WINDING WIRES - SOLDERABLE POLYURETHANE ENAMELLED ROUND COPPER WIRE, CLASS 130, WITH A BONDING LAYER
    BS EN 60317-34:1997 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 34: POLYESTER ENAMELLED ROUND COPPER WIRE, CLASS 130 L
    BS EN 60317-13 : 2010 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 13: POLYESTER OR POLYESTERIMIDE OVERCOATED WITH POLYAMIDE-IMIDE ENAMELLED ROUND COPPER WIRE, CLASS 200
    NBR IEC 60669-2-1 : 2014 SWITCHES FOR HOUSEHOLD AND SIMILAR FIXED ELECTRICAL INSTALLATIONS - PART 2-1: PARTICULAR REQUIREMENTS - ELECTRONIC SWITCHES
    BS 6811-3.6(1993) : 1993 AMD 8985 WINDING WIRES - SPECIFICATIONS FOR PARTICULAR TYPES OF ENAMELLED ROUND COPPER WINDING WIRES - BUNCHED SOLDERABLE POLYURETHANE ENAMELLED ROUND COPPER WIRE, CLASS 130, WITH SILK COVERING
    11/30249507 DC : 0 BS EN 60317-35 - SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 35: SOLDERABLE POLYURETHANE ENAMELLED ROUND COPPER WIRE, CLASS 155, WITH A BONDING LAYER
    12/30276797 DC : 0 BS EN 60317-51 ED 2.0 - SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 51: SOLDERABLE POLYURETHANE ENAMELLED ROUND COPPER WIRE, CLASS 180
    IEC 60317-0-7:2017 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 0-7: GENERAL REQUIREMENTS - FULLY INSULATED (FIW) ZERO-DEFECT ENAMELLED ROUND COPPER WIRE
    00/202085 DC : DRAFT MAY 2000 IEC 60669-2-1. ED. 4 - SWITCHES FOR HOUSEHOLD AND SIMILAR FIXED ELECTRICAL INSTALLATION - PART 2-1: PARTICULAR REQUIREMENTS - ELECTRONIC SWITCHES
    BIS IS 13730-12 : 2012 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 12: POLYVINYL ACETAL ENAMELLED ROUND COPPER WIRE, CLASS 120
    BS 6811-3.12(1993) : 1993 AMD 9467 WINDING WIRES - SPECIFICATIONS FOR PARTICULAR TYPES OF ENAMELLED ROUND COPPER WINDING WIRES - POLYAMIDE-IMIDE ENAMELLED ROUND COPPER WIRE, CLASS 200
    CEI EN 60317-20 : 2014 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 20: SOLDERABLE POLYURETHANE ENAMELLED ROUND COPPER WIRE, CLASS 155
    UNE-EN 60317-55:2014 Specifications for particular types of winding wires - Part 55: Solderable polyurethane enamelled round copper wire overcoated with polyamide, Class 180
    I.S. EN 60317-26:1998 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 26: POLYAMIDE-IMIDE ENAMELLED ROUND COPPER WIRE, CLASS 200
    05/30133636 DC : DRAFT MAY 2005 IEC 60317-55 - SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 55: SOLDERABLE POLYURETHANE ENAMELED ROUND COPPER WIRE OVERCOATED WITH POLYAMIDE, CLASS 180
    BS 6811-3.16(1993) : 1993 AMD 8598 WINDING WIRES - SPECIFICATIONS FOR PARTICULAR TYPES OF ENAMELLED ROUND COPPER WINDING WIRES - POLYESTER OR POLYESTERIMIDE OVERCOATED WITH POLYAMIDEIMIDE ENAMELLED ROUND COPPER WIRE, CLASS 200, WITH A BONDING LAYER
    CEI EN 60317-57 : 2011 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 57: POLYAMIDE-IMIDE ENAMELLED ROUND COPPER WIRE, CLASS 220
    BS 6811-3.15(1993) : 1993 AMD 8599
    BS 6811-3.14(1993) : 1993 AMD 8589 WINDING WIRES - SPECIFICATIONS FOR PARTICULAR TYPES OF ENAMELLED ROUND COPPER WINDING WIRES - SOLDERABLE POLYESTERIMIDE ENAMELLED ROUND COPPER WIRE, CLASS 180, WITH A BONDING LAYER
    BS EN 60182-2 : 1991 BASIC DIMENSIONS OF WINDING WIRES - PART 2: SPECIFICATION FOR MAXIMUM OVERALL DIAMETERS OF ENAMELLED ROUND WINDING WIRES
    BS ISO 9654:2004 Pliers and nippers for electronics. Single purpose nippers. Cutting nippers
    BS EN 60317-30:1997 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 30: POLYIMIDE ENAMELLED RECTANGULAR COPPER WIRE, CLASS 220
    NF EN 60317-57 : 2011 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 57: POLYAMIDE-IMIDE ENAMELLED ROUND COPPER WIRE, CLASS 220
    UNE-EN 60317-59:2016 Specifications for particular type of winding wires - Part 59: Polyamideimide enameled round copper wire, class 240
    NBR ISO 9654 : 2014 PLIERS AND NIPPERS FOR ELECTRONICS - SINGLE-PURPOSE NIPPERS - CUTTING NIPPERS
    BS IEC 60317-4 : 2015 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 4: SOLDERABLE POLYURETHANE ENAMELLED ROUND COPPER WIRE, CLASS 130
    CEI EN 60317-51 : 2015 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 51: SOLDERABLE POLYURETHANE ENAMELLED ROUND COPPER WIRE, CLASS 180
    I.S. EN 60317-13:2010 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 13: POLYESTER OR POLYESTERIMIDE OVERCOATED WITH POLYAMIDE-IMIDE ENAMELLED ROUND COPPER WIRE, CLASS 200
    I.S. EN 60317-30:1998 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 30: POLYIMIDE ENAMELLED RECTANGULAR COPPER WIRE, CLASS 220
    I.S. EN 60317-1:1996 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 1: POLYVINYL ACETAL ENAMELLED ROUND COPPER WIRE, CLASS 105
    EN 60317-0-7:2017 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 0-7: GENERAL REQUIREMENTS - FULLY INSULATED (FIW) ZERO-DEFECT ENAMELLED ROUND COPPER WIRE (IEC 60317-0-7:2017)
    I.S. EN 60317-51:2014 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 51: SOLDERABLE POLYURETHANE ENAMELLED ROUND COPPER WIRE, CLASS 180
    I.S. EN 60317-4:1996 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 4: SOLDERABLE POLYURETHANE ENAMELLED ROUND COPPER WIRE, CLASS 130
    I.S. EN 60317-42:1998 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 42: POLYESTER-AMIDE-IMIDE ENAMELLED ROUND COPPER WIRE, CLASS 200
    CEI EN 60317-8 : 2010 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 8: POLYESTERIMIDE ENAMELLED ROUND COPPER WIRE, CLASS 180
    BS EN 61347-2-6 : 2001 LAMP CONTROLGEAR - PART 2-6: PARTICULAR REQUIREMENTS FOR D.C. SUPPLIED ELECTRONIC BALLASTS FOR AIRCRAFT LIGHTING
    I.S. EN 60317-45:1999 SPECIFICATIONS FOR PARTICULAR TYPE OF WINDING WIRES - PART 45: POLYESTER ENAMELLED ROUND COPPER WIRE, CLASS 130
    I.S. EN 61347-1:2015 LAMP CONTROLGEAR - PART 1: GENERAL AND SAFETY REQUIREMENTS
    CEI EN 60317-46 : 2014 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 46: AROMATIC POLYIMIDE ENAMELLED ROUND COPPER WIRE, CLASS 240
    UNE-EN 60317-0-9:2016 Specifications for particular types of winding wires - Part 0-9: General requirements - Enamelled rectangular aluminium wire
    ISO 9654:2004 Pliers and nippers for electronics Single-purpose nippers Cutting nippers
    CEI EN 60317-0-7 : 2012 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 0-7: GENERAL REQUIREMENTS - FULLY INSULATED (FIW) ZERODEFECT ENAMELLED ROUND COPPER WIRE
    BS ISO 5744:2004 Pliers and nippers. Methods of test
    CEI EN 60317-21 : 2014 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 21: SOLDERABLE POLYURETHANE EN AMELLED ROUND COPPER WIRE OVERCOATED WITH POLYAMIDE, CLASS 155
    NBR IEC 61347-2-13 : 2012 LAMP CONTROL GEAR - PART 2-13: PARTICULAR REQUIREMENTS FOR D.C OR A.C SUPPLIED ELECTRONIC CONTROL GEAR FOR LED MODULES
    I.S. EN 60669-2-1:2004 SWITCHES FOR HOUSEHOLD AND SIMILAR FIXED ELECTRICAL INSTALLATIONS - PART 2-1: PARTICULAR REQUIREMENTS - ELECTRONIC SWITCHES
    NBR ISO 9656 : 2014 PLIERS AND NIPPERS FOR ELECTRONICS - TEST METHODS
    UNE-EN 60317-0-7:2012 Specifications for particular types of winding wires - Part 0-7: General requirements - Fully insulated (FIW) zero-defect enamelled round copper wire with nominal conductor diameter of 0,040 mm to 1,600 mm
    BS EN 60317-55 : 2014 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 55: SOLDERABLE POLYURETHANE ENAMELLED ROUND COPPER WIRE OVERCOATED WITH POLYAMIDE, CLASS 180
    CSA C22.2 No. 61347-2-13 : 2015 LAMP CONTROLGEAR - PART 2-13: PARTICULAR REQUIREMENTS FOR D.C. OR A.C. SUPPLIED ELECTRONIC CONTROLGEAR FOR LED MODULES
    I.S. EN 60317-0-7:2017 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 0-7: GENERAL REQUIREMENTS - FULLY INSULATED (FIW) ZERO-DEFECT ENAMELLED ROUND COPPER WIRE
    BIS IS 13730-26 : 1996 AMD 1 2013 SPECIFICATION FOR PARTICULAR TYPES OF WINDING WIRES - PART 26: POLYMIDE-IMIDE ENAMELLED ROUND COPPER WIRE, CLASS 200
    UNI ISO 9654 : 2011 PLIERS AND NIPPERS FOR ELECTRONICS - SINGLE-PURPOSE NIPPERS - CUTTING NIPPERS
    I.S. EN 60317-0-9:2015 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 0-9: GENERAL REQUIREMENTS - ENAMELLED RECTANGULAR ALUMINIUM WIRE
    I.S. EN 60317-55:2014 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 55: SOLDERABLE POLYURETHANE ENAMELLED ROUND COPPER WIRE OVERCOATED WITH POLYAMIDE, CLASS 180
    I.S. EN 60317-46:2014 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 46: AROMATIC POLYIMIDE ENAMELLED ROUND COPPER WIRE, CLASS 240
    I.S. EN 60317-12:2010 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 12: POLYVINYL ACETAL ENAMELLED ROUND COPPER WIRE, CLASS 120
    I.S. EN 60317-59:2016 SPECIFICATIONS FOR PARTICULAR TYPE OF WINDING WIRES - PART 59: POLYAMIDEIMIDE ENAMELED ROUND COPPER WIRE, CLASS 240
    ISO 5744:2004 Pliers and nippers Methods of test
    I.S. EN 61347-2-1:2004 LAMP CONTROLGEAR - PART 2-1: PARTICULAR REQUIREMENTS FOR STARTING DEVICES (OTHER THAN GLOW STARTERS)
    BIS IS 13730-4 : 2013 SPECIFICATION FOR PARTICULAR TYPES OF WINDING WIRES - PART 4: SOLDERABLE POLYURETHANE ENAMELLED ROUND COPPER WIRE, CLASS 130
    ISO 9656:2004 Pliers and nippers for electronics Test methods
    IEC 60669-2-1:2002+AMD1:2008+AMD2:2015 CSV Switches for household and similar fixed electrical installations -Part 2-1: Particular requirements - Electronic switches
    IEC 61347-1 REDLINE : 3ED 2015 LAMP CONTROLGEAR - PART 1: GENERAL AND SAFETY REQUIREMENTS
    IEC 60317-3:2004+AMD1:2010 CSV Specifications for particular types of winding wires - Part 3: Polyester enamelled round copper wire, class 155
    IEC 60317-2:2012 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 2: SOLDERABLE POLYURETHANE ENAMELLED ROUND COPPER WIRE, CLASS 130, WITH A BONDING LAYER
    IEC 60034-18-22 : 2.0 ROTATING ELECTRICAL MACHINES - PART 18-22: FUNCTIONAL EVALUATION OF INSULATION SYSTEMS - TEST PROCEDURES FOR WIRE-WOUND WINDINGS - CLASSIFICATION OF CHANGES AND INSULATION COMPONENT SUBSTITUTIONS
    IEC 60317-4:2015 Specifications for particular types of winding wires - Part 4: Solderable polyurethane enamelled round copper wire, class 130
    IEC 60317-59:2015 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 59: POLYAMIDE-IMIDE ENAMELLED ROUND COPPER WIRE, CLASS 240
    IEC TS 62101:2005 Electrical insulation systems - Short-time evaluation of combined thermal and electrical stresses
    IEC TS 62332-3:2016 ELECTRICAL INSULATION SYSTEMS (EIS) - THERMAL EVALUATION OF COMBINED LIQUID AND SOLID COMPONENTS - PART 3: HERMETIC MOTOR-COMPRESSORS
    I.S. EN 60317-20:2014 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 20: SOLDERABLE POLYURETHANE ENAMELLED ROUND COPPER WIRE, CLASS 155
    IEC 60317-41:1996 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - SOLDERABLE POLYESTER ENAMELLED ROUND COPPER WIRE, CLASS 130L
    I.S. EN 60317-23:2014 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 23: SOLDERABLE POLYESTERIMIDE ENAMELLED ROUND COPPER WIRE, CLASS 180
    I.S. EN 60317-21:2014 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 21: SOLDERABLE POLYURETHANE ENAMELLED ROUND COPPER WIRE OVERCOATED WITH POLYAMIDE, CLASS 155
    NF EN 60317-20 : 2014 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 20: SOLDERABLE POLYURETHANE ENAMELLED ROUND COPPER WIRE, CLASS 155
    NF EN 60317-23 : 2014 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 23: SOLDERABLE POLYESTERIMIDE ENAMELLED ROUND COPPER WIRE, CLASS 180
    NF EN 60317-36 : 2014 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 36: SOLDERABLE POLYESTERIMIDE ENAMELLED ROUND COPPER WIRE, CLASS 180, WITH A BONDING LAYER
    NF EN 60317-35 : 2014 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 35: SOLDERABLE POLYURETHANE ENAMELLED ROUND COPPER WIRE, CLASS 155, WITH A BONDING LAYER
    NF EN 60317-21 : 2014 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 21: SOLDERABLE POLYURETHANE ENAMELLED ROUND COPPER WIRE OVERCOATED WITH POLYAMIDE, CLASS 155
    UNE-EN 60317-51:2014 Specifications for particular types of winding wires - Part 51: Solderable polyurethane enamelled round copper wire, class 180
    IEC 60317-23:2013 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 23: SOLDERABLE POLYESTERIMIDE ENAMELLED ROUND COPPER WIRE, CLASS 180
    IEC 60317-19:1990+AMD1:1997+AMD2:1999 CSV SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 19: SOLDERABLE POLYURETHANE ENAMELLED ROUND COPPER WINDING WIRE OVERCOATED WITH POLYAMIDE, CLASS 130
    UNE-EN 60317-37:2014 Specifications for particular types of winding wires - Part 37: Polyesterimide enamelled round copper wire, class 180, with a bonding layer
    IEC 60317-57:2010 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 57: POLYAMIDE-IMIDE ENAMELLED ROUND COPPER WIRE, CLASS 220
    BS EN 60317-21 : 2014 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 21: SOLDERABLE POLYURETHANE ENAMELLED ROUND COPPER WIRE OVERCOATED WITH POLYAMIDE, CLASS 155
    UNE-EN 60317-38:2014 Specifications for particular types of winding wires - Part 38: Polyester or polyesterimide overcoated with polyamide-imide, enamelled round copper wire, class 200, with a bonding layer
    IEC 60317-37:2013 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 37: POLYESTERIMIDE ENAMELLED ROUND COPPER WIRE, CLASS 180, WITH A BONDING LAYER
    BS EN 60317-20 : 2014 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 20: SOLDERABLE POLYURETHANE ENAMELLED ROUND COPPER WIRE, CLASS 155
    BS EN 60317-11:2000 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 11: BUNCHED SOLDERABLE POLYURETHANE ENAMELLED ROUND COPPER WIRES, CLASS 130, WITH SILK COVERING
    UNE-EN 61347-1:2016 Lamp controlgear - Part 1: General and safety requirements
    IEC 60317-45:1998 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - POLYESTER ENAMELLED ROUND COPPER WIRE, CLASS 130
    IEC 60317-11:1999+AMD1:2005 CSV SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 11: BUNCHED SOLDERABLE POLYURETHANE ENAMELLED ROUND COPPER WIRES, CLASS 130, WITH SILK COVERING
    BS EN 60317-19 : 1996 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 19: SOLDERABLE POLYURETHANE ENAMELLED ROUND COPPER WIRE OVERCOATED WITH POLYAMIDE, CLASS 130
    UNE-EN 60317-46:2014 Specifications for particular types of winding wires - Part 46: Aromatic polyimide enamelled round copper wire, class 240
    BS EN 60317-23 : 2014 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 23: SOLDERABLE POLYESTERIMIDE ENAMELLED ROUND COPPER WIRE, CLASS 180
    UNE-EN 60317-42:1997 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES. PART 42: POLYESTER-AMIDE-IMIDE ENAMELLED ROUND COPPER WIRE, CLASS 200.
    BS EN 60317-37 : 2014 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 37: POLYESTERIMIDE ENAMELLED ROUND COPPER WIRE, CLASS 180, WITH A BONDING LAYER
    BS EN 60317-38 : 2014 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 38: POLYESTER OR POLYESTERIMIDE OVERCOATED WITH POLYAMIDE-IMIDE, ENAMELLED ROUND COPPER WIRE, CLASS 200, WITH A BONDING LAYER
    11/30252196 DC : 0 BS EN 61347-1:2008 + A2 - LAMP CONTROLGEAR - PART 1: GENERAL AND SAFETY REQUIREMENTS
    BS EN 61347-1:2015 (published 2015-06) Lamp controlgear General and safety requirements
    BS EN 60317-2 : 2012 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 2: SOLDERABLE POLYURETHANE ENAMELLED ROUND COPPER WIRE, CLASS 130, WITH A BONDING LAYER
    IEC 60317-22:2004+AMD1:2009 CSV Specifications for particular types of winding wires - Part 22: Polyester or polyesterimide enamelled round copper wire overcoated with polyamide, class 180
    BS EN 60317-36 : 2014 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 36: SOLDERABLE POLYESTERIMIDE ENAMELLED ROUND COPPER WIRE, CLASS 180, WITH A BONDING LAYER
    11/30203695 DC : 0 BS EN 60669-2-5 - SWITCHES FOR HOUSEHOLD AND SIMILAR FIXED ELECTRICAL INSTALLATIONS - PART 2-5: SWITCHES AND RELATED ACCESSORIES FOR USE IN HOME AND BUILDING ELECTRONIC SYSTEMS (HBES)
    IEC 60317-35:2013 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 35: SOLDERABLE POLYURETHANE ENAMELLED ROUND COPPER WIRE, CLASS 155, WITH A BONDING LAYER
    IEC 60317-36:2013 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 36: SOLDERABLE POLYESTERIMIDE ENAMELLED ROUND COPPER WIRE, CLASS 180, WITH A BONDING LAYER
    BS EN 60317-22 : 2004 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 22: POLYESTER OR POLYESTERIMIDE ENAMELLED ROUND COPPER WIRE OVERCOATED WITH POLYAMIDE, CLASS 180
    IEC 60317-13:2010 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 13: POLYESTER OR POLYESTERIMIDE OVERCOATED WITH POLYAMIDE-IMIDE ENAMELLED ROUND COPPER WIRE, CLASS 200
    IEC 60317-20:2013 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 20: SOLDERABLE POLYURETHANE ENAMELLED ROUND COPPER WIRE, CLASS 155
    BS EN 60317-8 : 2010 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 8: POLYESTERIMIDE ENAMELLED ROUND COPPER WIRE, CLASS 180
    IEC 60317-38:2013 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 38: POLYESTER OR POLYESTERIMIDE OVERCOATED WITH POLYAMIDE-IMIDE, ENAMELLED ROUND COPPER WIRE, CLASS 200, WITH A BONDING LAYER
    IEC 60317-42:1997+AMD1:2010 CSV SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 42: POLYESTER-AMIDE-IMIDE ENAMELLED ROUND COPPER WIRE, CLASS 200
    IEC 60317-51:2014 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 51: SOLDERABLE POLYURETHANE ENAMELLED ROUND COPPER WIRE, CLASS 180
    IEC 60317-7:1990+AMD1:1997+AMD2:1997 CSV SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - POLYIMIDE ENAMELLED ROUND COPPER WINDING WIRE, CLASS 220
    IEC 60317-46:2013 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 46: AROMATIC POLYIMIDE ENAMELLED ROUND COPPER WIRE, CLASS 240
    IEC 60317-12:2010 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 12: POLYVINYL ACETAL ENAMELLED ROUND COPPER WIRE, CLASS 120
    IEC 60317-8:2010 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 8: POLYESTERIMIDE ENAMELLED ROUND COPPER WIRE, CLASS 180
    UNE-EN 60317-20:2014 Specifications for particular types of winding wires - Part 20: Solderable polyurethane enamelled round copper wire, class 155
    UNE-EN 60317-23:2014 Specifications for particular types of winding wires - Part 23: Solderable polyesterimide enamelled round copper wire, class 180
    IEC 60317-34:1997 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - POLYESTER ENAMELLED ROUND COPPER WIRE, CLASS 130 L
    BS EN 60317-35 : 2014 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 35: SOLDERABLE POLYURETHANE ENAMELED ROUND COPPER WIRE, CLASS 155, WITH A BONDING LAYER
    IEC 60317-0-6:2001+AMD1:2006 CSV SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 0-6: GENERAL REQUIREMENTS - GLASS-FIBRE WOUND RESIN OR VARNISH IMPREGNATED, BARE OR ENAMELLED ROUND COPPER WIRE
    IEC 60317-55:2013 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 55: SOLDERABLE POLYURETHANE ENAMELLED ROUND COPPER WIRE OVERCOATED WITH POLYAMIDE, CLASS 180
    BS EN 60669-2-1 : 2004 SWITCHES FOR HOUSEHOLD AND SIMILAR FIXED ELECTRICAL INSTALLATIONS - PART 2-1: PARTICULAR REQUIREMENTS - ELECTRONIC SWITCHES
    IEC 61347-1:2015 RLV Lamp controlgear - Part 1: General and safety requirements
    IEC 60317-21:2013 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 21: SOLDERABLE POLYURETHANE ENAMELLED ROUND COPPER WIRE OVERCOATED WITH POLYAMIDE, CLASS 155
    IEC 60317-0-9:2015 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 0-9: GENERAL REQUIREMENTS - ENAMELLED RECTANGULAR ALUMINIUM WIRE
    EN 60317-0-6:2001/A1:2006 SPECIFICATION FOR PARTICULAR TYPES OF WINDING WIRES - PART 0-6: GENERAL REQUIREMENTS - GLASS-FIBRE WOUND RESIN OR VARNISH IMPREGNATED, BARE OR ENAMELLED ROUND COPPER WIRE
    CSA C22.2 No. 61347-2-13 : 2015(R2020) LAMP CONTROLGEAR - PART 2-13: PARTICULAR REQUIREMENTS FOR D.C. OR A.C. SUPPLIED ELECTRONIC CONTROLGEAR FOR LED MODULES
    EN 60317-12:2010 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 12: POLYVINYL ACETAL ENAMELLED ROUND COPPER WIRE, CLASS 120
    I.S. EN 60317-38:2014 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 38: POLYESTER OR POLYESTERIMIDE OVERCOATED WITH POLYAMIDE-IMIDE, ENAMELLED ROUND COPPER WIRE, CLASS 200, WITH A BONDING LAYER
    I.S. EN 60317-3:1996 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 3: POLYESTER ENAMELLED ROUND COPPER WIRE, CLASS 155
    I.S. EN 60317-7:1996 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 7: POLYIMIDE ENAMELLED ROUND COPPER WIRE, CLASS 220
    I.S. EN 60317-36:2014 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 36: SOLDERABLE POLYESTERIMIDE ENAMELLED ROUND COPPER WIRE, CLASS 180, WITH A BONDING LAYER
    I.S. EN 60317-8:2010 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 8: POLYESTERIMIDE ENAMELED ROUND COPPER WIRE, CLASS 180
    I.S. EN 60317-37:2014 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 37: POLYESTERIMIDE ENAMELLED ROUND COPPER WIRE, CLASS 180, WITH A BONDING LAYER
    I.S. EN 60317-11:1995 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 11: BUNCHED SOLDERABLE POLYURETHANE ENAMELLED ROUND COPPER WIRES, CLASS 130, WITH SILK COVERING
    NF EN 60317-12 : 2010 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 12: POLYVINYL ACETAL ENAMELLED ROUND COPPER WIRE, CLASS 120
    I.S. EN 60317-35:2014 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 35: SOLDERABLE POLYURETHANE ENAMELLED ROUND COPPER WIRE, CLASS 155, WITH A BONDING LAYER
    EN 61347-1:2015 LAMP CONTROLGEAR - PART 1: GENERAL AND SAFETY REQUIREMENTS (IEC 61347-1:2015)
    I.S. EN 60317-2:2012 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 2: SOLDERABLE POLYURETHANE ENAMELLED ROUND COPPER WIRE, CLASS 130, WITH A BONDING LAYER (IEC 60317-2:2012 (EQV))
    EN 61347-2-5:2001/corrigendum:2010 LAMP CONTROLGEAR - PART 2-5: PARTICULAR REQUIREMENTS FOR D.C. SUPPLIED ELECTRONIC BALLASTS FOR PUBLIC TRANSPORT LIGHTING
    DIN EN 60317-7 : 95 AMD 1 97 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 7: POLYIMIDE ENAMELLED ROUND COPPER WIRE, CLASS 220
    EN 60317-20:2014 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 20: SOLDERABLE POLYURETHANE ENAMELLED ROUND COPPER WIRE, CLASS 155 (IEC 60317-20:2013)
    EN 60317-21:2014 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 21: SOLDERABLE POLYURETHANE ENAMELLED ROUND COPPER WIRE OVERCOATED WITH POLYAMIDE, CLASS 155 (IEC 60317-21:2013)
    EN 60317-36:2014 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 36: SOLDERABLE POLYESTERIMIDE ENAMELLED ROUND COPPER WIRE, CLASS 180, WITH A BONDING LAYER (IEC 60317-36:2013)
    EN 60317-51:2014 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 51: SOLDERABLE POLYURETHANE ENAMELLED ROUND COPPER WIRE, CLASS 180 (IEC 60317-51:2014)
    EN 60317-26:1996/A2:2010 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 26: POLYAMIDE-IMIDE ENAMELLED ROUND COPPER WIRE, CLASS 200
    EN 61347-2-6:2001/corrigendum:2010 LAMP CONTROLGEAR - PART 2-6: PARTICULAR REQUIREMENTS FOR D.C. SUPPLIED ELECTRONIC BALLASTS FOR AIRCRAFT LIGHTING
    EN 60317-34 : 1997 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - POLYESTER ENAMELLED ROUND COPPER WIRE, CLASS 130
    EN 60317-8:2010 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 8: POLYESTERIMIDE ENAMELLED ROUND COPPER WIRE, CLASS 180
    EN 60317-13:2010 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 13: POLYESTER OR POLYESTERIMIDE OVERCOATED WITH POLYAMIDE-IMIDE ENAMELLED ROUND COPPER WIRE, CLASS 200
    EN 60317-7:1994/A2:1998 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 7: POLYIMIDE ENAMELLED ROUND COPPER WIRE, CLASS 220
    EN 60317-35:2014 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 35: SOLDERABLE POLYURETHANE ENAMELLED ROUND COPPER WIRE, CLASS 155, WITH A BONDING LAYER (IEC 60317-35:2013)
    EN 60317-11 : 2000 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - BUNCHED SOLDERABLE POLYURETHANE ENAMELLED ROUND COPPER WIRE, CLASS 130, WITH SILK COVERING
    EN 60317-42:1997/A1:2010 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 42: POLYESTER-AMIDE-IMIDE ENAMELLED ROUND COPPER WIRE, CLASS 200
    EN 60317-2:2012 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 2: SOLDERABLE POLYURETHANE ENAMELLED ROUND COPPER WIRE, CLASS 130, WITH A BONDING LAYER (IEC 60317-2:2012)
    EN 60317-0-9 : 2015 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 0-9: GENERAL REQUIREMENTS - ENAMELLED RECTANGULAR ALUMINIUM WIRE (IEC 60317-0-9:2015)
    EN 60317-59 : 2016 Specifications for particular type of winding wires - Part 59: Polyamideimide enameled round copper wire, class 240
    EN 60317-19:1995/A2:2000 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 19: SOLDERABLE POLYURETHANE ENAMELLED ROUND COPPER WIRE OVERCOATED WITH POLYAMIDE, CLASS 130
    EN 60317-38:2014 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 38: POLYESTER OR POLYESTERIMIDE OVERCOATED WITH POLYAMIDE-IMIDE, ENAMELLED ROUND COPPER WIRE, CLASS 200, WITH A BONDING LAYER
    EN 60317-37:2014 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 37: POLYESTERIMIDE ENAMELLED ROUND COPPER WIRE, CLASS 180, WITH A BONDING LAYER (IEC 60317-37:2013)
    EN 60317-22:2004/A1:2010 Specifications for particular types of winding wires - Part 22: Polyester or polyesterimide enamelled round copper wire overcoated with polyamide, class 180
    EN 60317-23:2014 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 23: SOLDERABLE POLYESTERIMIDE ENAMELLED ROUND COPPER WIRE, CLASS 180 (IEC 60317-23:2013)
    EN 60317-46:2014 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 46: AROMATIC POLYIMIDE ENAMELLED ROUND COPPER WIRE, CLASS 240 (IEC 60317-46:2013)
    EN 61347-2-1:2001/A2:2014 LAMP CONTROLGEAR - PART 2-1: PARTICULAR REQUIREMENTS FOR STARTING DEVICES (OTHER THAN GLOW STARTERS) (IEC 61347-2-1:2000/A2:2013)
    EN 60317-1 : 1994 AMD 2 1998 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 1: POLYVINYL ACETAL ENAMELLED ROUND COPPER WIRE, CLASS 105
    EN 60317-55:2014 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 55: SOLDERABLE POLYURETHANE ENAMELLED ROUND COPPER WIRE OVERCOATED WITH POLYAMIDE, CLASS 180 (IEC 60317-55:2013)
    DIN EN 60317-3:1995-11 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 3: POLYESTER ENAMELLED ROUND COPPER WIRE, CLASS 155
    EN 60317-57 : 2010 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 57: POLYAMIDE-IMIDE ENAMELLED ROUND COPPER WIRE, CLASS 220
    EN 60317-30:1996/A2:2005 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 30: POLYIMIDE ENAMELLED RECTANGULAR COPPER WIRE, CLASS 220
    EN 61347-2-4:2001/corrigendum:2010 LAMP CONTROLGEAR - PART 2-4: PARTICULAR REQUIREMENTS FOR D.C. SUPPLIED ELECTRONIC BALLASTS FOR GENERAL LIGHTING
    EN 60317-4:1994/A2:2000 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 4: SOLDERABLE POLYURETHANE ENAMELLED ROUND COPPER WIRE, CLASS 130
    EN 60317-3 : 94 AMD 1 98 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 3: POLYESTER ENAMELLED ROUND COPPER WIRE, CLASS 155
    EN 60317-45 : 1998 SPECIFICATIONS FOR PARTICULAR TYPE OF WINDING WIRES - POLYESTER ENAMELLED ROUND COPPER WIRE, CLASS 130

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO 3:1973 Preferred numbers Series of preferred numbers
    IEC 60172:2015 Test procedure for the determination of the temperature index of enamelled and tape wrapped winding wires
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective