IEC 60793-1-2:1995
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Optical fibres - Part 1: Generic specification - Section 2: Measuring methods for dimensions
Hardcopy , PDF , PDF 3 Users , PDF 5 Users , PDF 9 Users
01-08-2001
22-11-1995
FOREWORD
Clause
1 Scope and object
2 Normative reference
3 Dimensional tests
4 Reference surface
5 Concentricity error
6 Tolerances
7 Operational definitions
8 Method IEC 793-1-A1 - Refractive index profile
8.1 Method IEC 60793-1-A1A - Refractive index
profile - Refracted near-field method
8.2 Method IEC 60793-1-A1B - Refractive index
profile, transverse interference method
9 Method IEC 793-1-A2 - End face geometry of optical
fibre determined from the near-field light
distribution
9.1 Object
9.2 Geometry parameters
9.3 Apparatus
9.4 Test sample
9.5 Procedure
9.6 Results
10 Method IEC 793-1-A3 - Side view light distribution
for primary coating
10.1 Object
10.2 Sample preparation
10.3 Apparatus
10.4 Procedure
11 Method IEC 793-1-A4 - Mechanical diameter measurement
11.1 Object
11.2 Scope
11.3 Test apparatus
12 Method IEC 793-1-A5 - Mechanical length measurement
13 Method IEC 793-1-A6 - Length measurement by delay
measuring of transmitted pulse and/or reflected pulse
13.1 Object
13.2 Principle
13.3 Sample
13.4 Apparatus
13.5 Procedure
13.6 Results
13.7 Documentation
14 Method IEC 793-1-A7 - Fibre elongation measurement
method
14.1 Object
14.2 Description
14.3 Apparatus
14.4 Procedure
14.5 Results
15 Method IEC 60793-1-A8 - Length measurement of an
optical fibre by the phase-shift method
15.1 Object
15.2 Scope
15.3 Apparatus
15.4 Sampling and specimens
15.5 Procedure
15.6 Calculation and interpretation of results
15.7 Documentation
Annex A (informative) Determination of group index
Figures
Gives the measureing methods applicable to environmental tests of optical fibres. The methods are to be used for inspection of optical fibres for commercial puposes. They establish uniform requirements for geometrical characteristics of optical fibres.
DevelopmentNote |
Supersedes IEC 60793 PT1 (1992)
|
DocumentType |
Standard
|
Pages |
107
|
PublisherName |
International Electrotechnical Committee
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
Standards | Relationship |
NEN IEC 60793-1-2 : 1999 AMD 2 2000 | Identical |
BS EN 61290-2-2:1998 | Optical fibre amplifiers. Basic specification Test methods for optical power parameters. Electrical spectrum analyzer |
NF ISO 14881 : 2004 | |
I.S. EN 187105:2002 | SINGLE MODE OPTICAL CABLE (DUCT/DIRECT BURIED INSTALLATION) |
06/30148633 DC : DRAFT APR 2006 | EN 60794-3-20 - OPTICAL FIBRE CABLES - PART 3-20: OUTDOOR CABLES - FAMILY SPECIFICATION FOR SELF-SUPPORTING AERIAL TELECOMMUNICATION CABLES |
97/202499 DC : 0 | |
02/205756 DC : DRAFT MAY 2002 | IEC 60794-4. ED 2.0 - OPTICAL FIBRE CABLES - PART 4: SECTIONAL SPECIFICATION - AERIAL OPTICAL CABLES ALONG ELECTRICAL POWER LINES |
BS EN 61290-2-1:1998 | Optical fibre amplifiers. Basic specification Test methods for optical power parameters. Optical spectrum analyzer |
CSA ISO/IEC 9314-4 : 2002 | INFORMATION TECHNOLOGY - FIBRE DISTRIBUTED DATA INTERFACE (FDDI) - PART 4: SINGLE-MODE FIBRE PHYSICAL LAYER MEDIUM DEPENDENT (SMF-PMD) |
EN ISO 14881:2005 | Integrated optics - Interfaces - Parameters relevant to coupling properties (ISO 14881:2001) |
BS EN 187105:2002 | Single mode optical cable (duct/direct buried installation) |
NF EN 187105 : 2002 | SINGLE-MODE OPTICAL FIBRE CABLE (DUCT/DIRECT BURIED INSTALLATION) |
CSA ISO/IEC 9314-4 : 2002 : R2015 | INFORMATION TECHNOLOGY - FIBRE DISTRIBUTED DATA INTERFACE (FDDI) - PART 4: SINGLE-MODE FIBRE PHYSICAL LAYER MEDIUM DEPENDENT (SMF-PMD) |
07/30172946 DC : 0 | BS EN 60793-1-47 IEC 60793-1-47 - OPTICAL FIBRES - PART 1-47: MEASUREMENT METHODS AND TEST PROCEDURES - MACROBENDING LOSS |
CSA ISO/IEC 9314-4 : 2002 : R2010 | INFORMATION TECHNOLOGY - FIBRE DISTRIBUTED DATA INTERFACE (FDDI) - PART 4: SINGLE-MODE FIBRE PHYSICAL LAYER MEDIUM DEPENDENT (SMF-PMD) |
ISO/IEC 9314-9:2000 | Information technology Fibre Distributed Data Interface (FDDI) Part 9: Low-cost fibre physical layer medium dependent (LCF-PMD) |
BS EN 61290-6-1:1998 | Optical fibre amplifiers. Basic specification Test methods for pump leakage parameters. Optical demultiplexer |
ISO/IEC 9314-4:1999 | Information technology Fibre Distributed Data Interface (FDDI) Part 4: Single Mode Fibre Physical Layer Medium Dependent (SMF-PMD) |
DIN EN ISO 14881:2005-05 | Integrated optics - Interfaces - Parameters relevant to coupling properties (ISO 14881:2001) |
CEI EN 61290-6-1 : 1999 | OPTICAL FIBRE AMPLIFIERS - BASIC SPECIFICATION - TEST METHODS FOR PUMP LEAKAGE PARAMETERS - OPTICAL DEMULTIPLEXER |
BS IEC 60793-2:1998 | Optical fibres Product specifications |
CEI EN 61290-2-2 : 1999 | OPTICAL FIBRE AMPLIFIERS - BASIC SPECIFICATION - PART 2-2: TEST METHODS FOR OPTICAL POWER PARAMETERS - ELECTRICAL SPECTRUM ANALYZER |
07/30148629 DC : 0 | BS EN 60794-3-10 - OPTICAL FIBRE CABLES - PART 3-10: OUTDOOR CABLES - FAMILY SPECIFICATION FOR DUCT AND DIRECTLY BURIED OPTICAL TELECOMMUNICATION CABLES |
IEC 60793-1-5:1995 | Optical fibres - Part 1: Generic specification - Section 5: Measuring methods for environmental characteristics |
BS EN ISO 14881:2005 | Integrated optics. Interfaces. Parameters relevant to coupling properties |
ISO 14881:2001 | Integrated optics Interfaces Parameters relevant to coupling properties |
05/30128522 DC : DRAFT JAN 2005 | IEC 60793-1-47 - OPTICAL FIBRES - PART 1-47: MEASUREMENT METHODS AND TEST PROCEDURES - MACROBENDING LOSS |
BS ISO 14881:2001 | Integrated optics. Interfaces. Parameters relevant to coupling properties |
IEC 60793-1-3:2000 | Optical fibres - Part 1-3: Generic specification - Measuring methods for mechanical characteristics |
CEI EN 61290-2-3 : 1999 | OPTICAL FIBRE AMPLIFIERS - BASIC SPECIFICATION - PARTS 2-3: TEST METHODS FOR OPTICAL POWER PARAMETERS - OPTICAL POWER METER |
I.S. EN ISO 14881:2005 | INTEGRATED OPTICS - INTERFACES - PARAMETERS RELEVANT TO COUPLING PROPERTIES |
EN 187105:2002 | Single mode optical cable (duct/direct buried installation) |
IEC 60794-1:1996 | Optical fibre cables - Part1: Generic specification (Revision to IEC 794-1) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.